Navigation

  • Page 1

    CNC Z32 NUMERICAL CONTROLLER ALARMS USER MANUAL This manual contains information destined exclusively to the users of D.Electron products for the correct usage of the equipment supplied. It is forbidden to copy any part of this manual or pass it to thirds for ot...

  • Page 2

  • Page 3

    CNC Z32 Numerical Controller Alarms – M291GB i INDEX 1 5,. 5, 5,DESCRIPTION..................................................................................................................... 5,1 5, 5,2. 5, 5,SERIOUS 5, SYSTEM 5, ERRORS 5,.....................................................

  • Page 4

  • Page 5

    CNC Z32 Numerical Controller Alarms – M291GB 1 1. DESCRIPTION This manual describes all the Z32 alarms valid at the issue date of the manual. WARNING These information and data may change depending on the version of the Z32 software. Therefore, they may be no longer effective in the case of suc...

  • Page 6

    CNC Z32 Numerical Controller Alarms – M291GB 2 errorgen 00001110 Exclusively for FlorenZ-Linux systems, 2 mS interrupt overlap. It is originated by a too slow processor or (most likely) by an inadequate video driver. errorgen 00001200 This alarm may come when a simulation of the Z32 is done und...

  • Page 7

    CNC Z32 Numerical Controller Alarms – M291GB 3 errorgen 00080000 Generated when a Z32 software version with serial emulator is installed, without the appropriate key or with a key not enabled. errorgen 03000000 Indicates a software malfunction that should be notified to D.Electron. errorgen 050...

  • Page 8

    CNC Z32 Numerical Controller Alarms – M291GB 4 CN0702 - NODES CONNECTED TO Z-LINK INFERIOR TO THE SETUP In the peripheral fiber optic system (DE1065 and DE 1075 master-link boards) the number of connected nodes is defined in the setup. If the number of physical nodes is inferior to calibration,...

  • Page 9

    CNC Z32 Numerical Controller Alarms – M291GB 5 CN1502 - ABSOLUTE AXIS, FRACTIONARY, ABSOLUTE TRAVEL TOO SHORT (< 10 AXIS TURNS) This alarm refers to absolute axes, cyclic, without end-of-travel, having a mechanical gear-ratio such that in an absolute travel of the transducer are contained a ...

  • Page 10

    CNC Z32 Numerical Controller Alarms – M291GB 6 CNC102 - PROCESS 2 TO 5 SOFTWARE OPTION Alarm related to the software options. It appears when activating the Process 2 to 5 without having installed the correct license that enables them. CNC202 - GANTRY AXES SOFTWARE OPTION Alarm related to the s...

  • Page 11

    CNC Z32 Numerical Controller Alarms – M291GB 7 The most probable reasons are: - The power supply of the master-link is turnad OFF - The Ethernet cable is disconnected or is faulty CN0407 - DRIVER INTERNAL ERROR 4 Internal alarm: it must never come. If present, please contact D.Electron. CN0507 ...

  • Page 12

    CNC Z32 Numerical Controller Alarms – M291GB 8 CN1307 - TRANSMISSION TIMEOUT 0 Indicates an excessive delay in the data transmission channel 0 between the Linux PC and the Master-Link board. It comes from severe communication problems between the Linux PC and the Master-link board. It may be or...

  • Page 13

    CNC Z32 Numerical Controller Alarms – M291GB 9 communication) are very similar one to another: they may interchange following almost casual rules. CN1807 - MASTER-LINK CMOS BATTERY LOW Indicates that the lythium battery used on the master-link for the CMOS memory back-up is discharged or faulty...

  • Page 14

    CNC Z32 Numerical Controller Alarms – M291GB 10 This error is mainly originated by hardware problems: servodrive OFF, optical fibre not connected or faulty, heavy electrical noise, faulty servodrive. CN2507 - WRONG CONNECTION WITH Z-STAR2 N. 4 Indicates an error in the connection between master...

  • Page 15

    CNC Z32 Numerical Controller Alarms – M291GB 11 CN0308 - ZSTAR: CONNECTION ERROR TO ZBOX NR. 1,2 This alarm appears when the first and the second Z-Box’s are not communicating in the right way with the master-link. The connection error can be caused by hardware problems, like not connected o...

  • Page 16

    CNC Z32 Numerical Controller Alarms – M291GB 12 CN1C09 04 + 08 + 10 etc. CNFF09 - Z-STAR: WRONG Z-LINK BEHAVIOUR Error in the DE1108 (Z-Star) board: the Z-Link in not working in the right way with loss of communication cycles. 3.5 CN..10 - CMOS alarms The alarms type CNxx10 refer to the perman...

  • Page 17

    CNC Z32 Numerical Controller Alarms – M291GB 13 CN0410 - Z32 file checksum error Indicates that one or more Z32 files had a checksum error upon powering on. The area subjected to checksum error will be replaced by diesis marks ####... CN0810 – Error: parameters PRM[ ] It is shown in the start...

  • Page 18

    CNC Z32 Numerical Controller Alarms – M291GB 14 Should more than one axis be in alarm mode, the code displayed is the one referring to the axis with lowest logical number, and switches to the next available code when activity 7 (zero restart) is executed. Any CN..12 alarm is immediately display...

  • Page 19

    CNC Z32 Numerical Controller Alarms – M291GB 15 locate which axis triggered the error, pursuit errors must be displayed (see chapter “Operating Modes”, paragraph “Special Displays: Axes and Axis errors”). CN0313 The processor sent to the axis motion controller an incorrect command. This...

  • Page 20

    CNC Z32 Numerical Controller Alarms – M291GB 16 CN1113 Negative W axis in a SCARA manipulator. A SCARA manipulator’s peripheral axis assumes a negative value during movement. CN1213 and CN1313 Alarms relative to errors in DNC transmission from a host using codos type 16 commands (e.g. ZTERM)....

  • Page 21

    CNC Z32 Numerical Controller Alarms – M291GB 17 CN1C13 The CN1C13 alarm communicates that at least once, the AT data reading has been carried out with excessive delay (telegrams from the Z-SER linked drives to the Z32 CPU). As a consequence, this may provoke faulty axis readings (e.g. repeated ...

  • Page 22

    CNC Z32 Numerical Controller Alarms – M291GB 18 CN2813 This alarm appears when programming a movement involving more that 5 interpolating axes while it is active a function not compatible with movements involving more that 5 interpolating axes. CN2A13 This alarm appears (on all the active proce...

  • Page 23

    CNC Z32 Numerical Controller Alarms – M291GB 19 CN3513 Spindle head has undefined state. This alarm comes in machines equipped with head-exchanging system if a CN activity is requested (Automatic, MDI, JOG) before the PLC has defined what head is installed. Probable cause: the head exchanging s...

  • Page 24

    CNC Z32 Numerical Controller Alarms – M291GB 20 3.8 CN..14 - Machine programming and usage alarms These alarms indicate a programming error, a program permanent memory storage fault, or an incorrect usage of some activities. They are usually accompanied by a plaintext explanation on the command...

  • Page 25

    CNC Z32 Numerical Controller Alarms – M291GB 21 CN2414 - RETURN ERROR It is an error message related to a return from a series of rows, which should never happen. If it does, notify D.Electron. CN2514 - BASE ORIGINS ERROR Base origins are not correct; the file containing the current process’ ...

  • Page 26

    CNC Z32 Numerical Controller Alarms – M291GB 22 CN3414 - PREVIOUS OPEN In the profile programming the segment preceding the one shown on the command line is open (see also the geometry section in the programming manual). CN3514 - ROW TOO LONG The row displayed on the command line (alone or conc...

  • Page 27

    CNC Z32 Numerical Controller Alarms – M291GB 23 CN4B14 - TOO MANY PARAMETERS Too many two-character user parameters have been put in a part-program (e.g. HA, HB, HC, ... up to a maximum of sixty). CN4C14 - ANSWER ERROR CN4D14 - SUSPENDED BLOCKS INTERNAL ERROR CN4E14 - :L DISK FILE ERROR Related...

  • Page 28

    CNC Z32 Numerical Controller Alarms – M291GB 24 CN5B14 - <<FORMULA G116/17/18/22 + G43/G44/G45>> One of G43, G44 and G45 has been programmed while one of G116, G117, G118 or G122 is active. This situation triggers an alarm as it could lead to wrong measure calculations in relation t...

  • Page 29

    CNC Z32 Numerical Controller Alarms – M291GB 25 CN6114 - G128 INCOMPATIBLE FUNCTION Error related to the “process lock”, the specific running of multi-process or synchronised-axes machines. During the lock process, the part-program on correlated movements and activities. The following funct...

  • Page 30

    CNC Z32 Numerical Controller Alarms – M291GB 26 CN6E14 - LOOP WITHOUT DO A LOOP has been programmed without an open DO. CN6F14 - FPU INTERNAL ERROR This is an internal error that should never happen. If it does, notify D.Electron. CN7014 - G126/G127 WRONG DATA This alarm is related to the G1...

  • Page 31

    CNC Z32 Numerical Controller Alarms – M291GB 27 Internal errors (should never happen): 101 too many files to be opened 102 no file to be opened 103 not defined 104 global to local file assignment is inconsistent 105 write calling with file not opened for the calling in process 106 too long wr...

  • Page 32

    CNC Z32 Numerical Controller Alarms – M291GB 28 CN8214 - G800/1/2 PC FILE ERROR This alarm refers to G800, G801 and G802 functions for managing “canned cycle”, “positioning macros” and “machining macros” saved on hard-disk. This alarm appears when a cycle or a macro is called, but t...

  • Page 33

    CNC Z32 Numerical Controller Alarms – M291GB 29 CNEx14 - POSITIVE SOFTWARE END OF TRAVEL This alarm indicates that a movement has been programmed which would exceed the positive x axis end run, where x is the axis' logical number. This alarm supersedes the generic CN3114 END OF TRAVEL. CNFx14 ...

x