Navigation

  • Page 1

    Dec. 2010 Ver1 robert.appleton@doosan.com - 1 - Communications Instructions for DOOSAN, FANUC Controls  Ethernet & RS-232 for; 18i, 21i, 0ib and c 30i Series & 0id

  • Page 2

    Dec. 2010 Ver1 robert.appleton@doosan.com - 2 - Table of Contents  Section 1 .............................................................................................................. 3 Ethernet Set-up for the PC ........................................................................

  • Page 3

    Ethernet Set-up for the PC Dec. 2010 Ver1 robert.appleton@doosan.com - 3 - Section 1 Ethernet Set-up for the PC Doosan Turning centers and Machining Centers that are equipped with FANUC controls, Ethernet port and the “Embedded Ethernet” function can be connected either to a local area...

  • Page 4

    Ethernet Set-up for the PC Dec. 2010 Ver1 robert.appleton@doosan.com - 4 - Hardware requirements  Personal Computer equipped with LAN connection and Windows operating system (Windows 97 through Windows 7), or a PC workstation connected to a local area network.  LAN Cable a) Cable type ...

  • Page 5

    Ethernet Set-up for the PC Dec. 2010 Ver1 robert.appleton@doosan.com - 5 - “Accessories”. At the command prompt, type in the command as shown, below: In case of Windows XP or later, type in: ipconfig (enter) In case of Windows - other than XP -, type in: winipcfg (enter) The system wi...

  • Page 6

    Ethernet Set-up for the PC Dec. 2010 Ver1 robert.appleton@doosan.com - 6 - The tile shown below will appear. First you must select the root directory. To do this click the “…” button at the end of the dialog box underneath the “Root Directory”, a window will pop up and you can br...

  • Page 7

    Ethernet Set-up for the PC Dec. 2010 Ver1 robert.appleton@doosan.com - 7 - This will display the tile shown below. Check boxes as desired then click save. Close the tile. Do not close the program.

  • Page 8

    Ethernet NC setup for 18i, 21i, 0ib, c Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 8 - Section 2 Ethernet NC setup instructions for 18i, 21i, 0ib, 0ic Controls 1. Go to the NC. Select MDI-mode. Set “parameter write enable”=1.  On the same page, set the I/O-channel =9  Pr...

  • Page 9

    Ethernet NC setup for 18i, 21i, 0ib, c Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 9 - settings are incorrect or the network cables are not connected an alarm will appear: “DATA NOT FOUND” 4. In “EDIT”-mode, the system is ready to transfer programs or other NC-data to and f...

  • Page 10

    Ethernet NC setup for 31i, 32i Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 10 - Section 3 Ethernet NC setup instructions for 31i, 32i Controls Note: 31i shown, 32i controls are similar  For a 2 path machine, select the Lower Path on the Control Panel  Select MDI on the C...

  • Page 11

    Ethernet NC setup for 31i, 32i Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 11 -  Settings for the LAN can be found by pressing the [System] Hard key then pressing the [+] soft key repeatedly until the Screen above appears. Press [EMBED PORT] The MAC Address (Media Access Contr...

  • Page 12

    Ethernet NC setup for 31i, 32i Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 12 - The Host Name (IP Address). (The Host computer is the computer running the FTP Server software, (PC)) FTP means File Transfer Protocol. This computer will direct all traffic between the two Systems. ...

  • Page 13

    Ethernet NC setup for 31i, 32i Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 13 -  Press [OPRT]  Finally Press [PING FTP1] This will check the communications of the configuration, If the connections and settings are correct, the host computer will respond with the (response i...

  • Page 14

    Ethernet NC setup for 0iD Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 14 - Section 4 Ethernet NC setup instructions for 0i_d Controls Note: 0itd 10” Screen shown, 8” controlls are similar  Select MDI on the Control Panel  Settings for the LAN can be found by pressing ...

  • Page 15

    Ethernet NC setup for 0iD Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 15 - The MAC Address (Media Access Control) are most often assigned by the manufacturer of a network interface card (NIC) and are stored in its hardware. This number cannot be changed. The IP address of the Eth...

  • Page 16

    Ethernet NC setup for 0iD Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 16 -  Fill out the HOST NAME (IP ADDRESS) with the IP address from the PC (Host) 169.254.241.70  Port Number 21  User Name, if any (Must match the PC configuration)  Password, If any (Must match the ...

  • Page 17

    Ethernet NC setup for 0iD Controls Dec. 2010 Ver1 robert.appleton@doosan.com - 17 -  Go to [Program] , and select the [EMB ETHER] to see the Directory from the Host PC (This is the Folder that was selected from the FTP Server during setup of the PC side.) The status of the FTP I/O can...

  • Page 18

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 18 - Section 5 RS-232 Set-up, PC Configuration HyperTerminal can be found in the accessory folder of all MS Windows computers prior to Windows Vista. For Windows Vista and later, please follow the instructions in t...

  • Page 19

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 19 - A USB to serial adapter is required for most new computers today. Windows 7 will most likely find the drivers it needs, if not, a source for USB to Serial drivers can be found at: http://www.prolific.com.tw/eng...

  • Page 20

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 20 - RS-232 C Interface Wiring (For use with “DC Codes”)

  • Page 21

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 21 - RS-232 C Interface Wiring (No Hand Shake)

  • Page 22

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 22 - A usb to RS-232 adapter may be needed to connect modern PCs or laptops to the CNC Machine. These can be obtained from many internet and local sources. These adapters have been tested and provide the necess...

  • Page 23

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 23 - Communication with CNC via RS 232C using Hyper Terminal 1 It is strongly recommended that a working connection between the PC and Machine be established using the methods contained in this text before using an...

  • Page 24

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 24 - Make sure that this data is compatible with the communication parameters as set at the CNC (as per notes, above). When data entry is completed, click: “OK”. 4. Now, the main communication page is displayed...

  • Page 25

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 25 - On the PC the program text will now be rolling diagonally across the screen. This is normal. If the text consists of a lot of unusual looking characters the communications parameters are not set as instructed. (...

  • Page 26

    RS-232 Set-up, NC Configuration Dec. 2010 Ver1 robert.appleton@doosan.com - 26 -  Never click on “Send file” Notes on changing the communication settings for Hyper Terminal 1. Hang up (disconnect) the line. 2. On top of the Hyper Terminal tile, click on “Properties” 3. For cha...

  • Page 27

    Appendix Dec. 2010 Ver1 robert.appleton@doosan.com - 27 - Appendix Revision History: Version 1.0 December 1, 2010

x