Navigation

  • Page 1

    GE Fanuc AutomationComputer Numerical Control ProductsSeries 0 / 00 / 0-Matefor Machining CenterParameter ManualGFZ-61410E/03November 1996

  • Page 2

    GFL-001Warnings, Cautions, and Notesas Used in this PublicationWarningWarning notices are used in this publication to emphasize that hazardous voltages, currents,temperatures, or other conditions that could cause personal injury exist in this equipment ormay be associated with its use.In situatio...

  • Page 3

    Applicable modelsThe models covered by this manual, and their abbreviations are:\Product NameAbbreviationsFANUC Series O-MCO-MCFANUC Series 0-MF0-MFSeries 0FANUC Series 0-GSC0-GSCFANUC Series 00-MC00-MCSeries 00FANUC Series OO-GSC00-GSCFANUC Series O-Mate MCO-Mate MCSeries O-MateFANUC Series O-Ma...

  • Page 4

    CONTENTSFUNCTION PARAMETERS (FOR MACHINING SERIES) ............................................ 11.Settingparameters .................................................................................22.Parameters related to the reader/punch interface and remote buffer ................................

  • Page 5

    FUNCTION PARAMETERS (FOR MACHINING SERIES)(1)(2)(3)(4)(5)(6)(7)(8)(9)(10)(11)(12)(13)(14)(15)(16)(17)W)(19)(20)(21)(22)(2%(24(25)(26)(27)(28)(29)(30)W)(32)(33)(34)(35)(36)(37)NOTES(I)(2)Setting parametersParameters related to the reader/punch interface and remote bufferParameters related to contr...

  • Page 6

    1) Setting parameters (l/l)No.1 Symbol 1Description0000 1REVX, Y, 4 1 The mirror image of each axis is disabled/enabled.0000 1TVON 1 When a program is registered, a TV check is not executed/is executed.0000 1IS0 1 The code system used to output a program is EIA/ISO.0000 1INCH1 The least input inc...

  • Page 7

    (2) Parameters related to the reader/punch interface and remote buffer (l/l)No.SymbolDescription0002#0STP2(I/0=0) The stop bit is l/2.0012#0STP2 (I/0=1)0050#0STP2 (l/0=2)0051 #OSTP2 (l/0=3)0002#2ASR33(I/0=0) FANUC PPR etc./20+nA current interface0012#0ASR33 (l/0=1)0002#3RSASCI(l/0=0) The input/ou...

  • Page 8

    (3) Parameters related to controlled axes and the increment system (l/l)No.SymbolDescription0001 #OSCWThe least command increment (output unit) for a linear axis is one millimeter/inch.7001 #Osews0003#0 to #3ZM*(X to 4) The direction of a reference position return and initial direction are positi...

  • Page 9

    (4) Parameters related to coordinate systems (l/l)No.SymbolDescription0010#7APRSAt a manual reference position return, automatic coordinate system setting is not7010#7APRSS executed/is executed.0024#6CLCLAt a manual reference position return, the local coordinate system is not canceled/iscanceled...

  • Page 10

    (5) Parameters related to the stroke limit (l/l)No.SymbolDescription0008#6OTZNA Z-axis stored stroke check is executed/is not executed.0015#4LM2The signal for switching the second stored stroke limit is disabled/enabled.The inhibited area of the third stored stroke limit is the inside/outside.002...

  • Page 11

    (6) Parameters related to the feedrate (2/2)No.0393#4SymbolDescriptionHLCLMPIn helical interpolation, the feedrate is not clamped/is clamped to the maximum cuttingfeedrate.I_0393#5 )STOVO 1 If the cutting feedrate override is 0% in rapid traverse, a stop does not occur/occurs.0397#2 1OVR255 1 The...

  • Page 12

    (7) Parameters related to acceleration/deceleration control (l/2)No.1 Symbol 1Description0020#5 1NCIPS 1 A position check is executed/is not executed.0045#3LSUPFor cutting feed, exponential acceleration/deceleration is executed/linear acceleration/deceleration after interpolation is executed.0045...

  • Page 13

    17) Parameters related to acceler ation/deceleration control (2/2)No.( SymbolDescription0865 1---a--Critical angle between two blocks for automatic corner decelerationTime constant for exponential acceleration/deceleration of cutting feed (for look-ahead control)0877 1------Time constant for line...

  • Page 14

    (8) Parameters related to servo motors (212)No.SymbolDescription\0265- - - - - -Time interval for leveling the current value display on the servo adjustment screen0405 -_----Maximum position deviation for which manual reference position return is assumed tobe possible0452 to 0457- - - - - -(X to ...

  • Page 15

    (9) Parameters related to DI/DO (l/l)No.SymbolDescription0001#2DCSThe START key on the MDI panel is connected through the machine/is not connectedthrough the machine.0001#5DECI(X to 4) At a reference position return, deceleration occurs when the decelerationsignal is set to O/l.7001#5DECIS (5, 6)...

  • Page 16

    (10) Parameters related to the CRT/MDI, display, and editing (2/4)No.0015#10015#60018#50018#70019#60019#70023#0 to #60028#00028#20028#30029#60030#40032#20032#30032#70035#0 to #30038#30040#00040#40045#00045#10046#40048#10048#20048#50048#7SymbolDescriptionNWCHThe amount of tool wear compensation is...

  • Page 17

    (IO) Parameters related to the CRT/MDI, display, and editing (3/4)No.SymbolDescription0050#1NOFMKWhen a sequence number is searched for, the format is checked/is not checked.0056#0NOCNDWhen the length of part program storage is 120 or 320 m, or if the background editingfunction is provided, memor...

  • Page 18

    (IO) Parameters related to the CRT/MD& display, and editing (4/4)No.ISymbolDescriptionThe wear offset protection state is based on bit 0 (NOINOW) of parameter No.0078/program protection signal KEY cG122#3>.The geometry offset protection state is based on bit 1 (NOINOG) of parameter No.0078...

  • Page 19

    (11) Parameters related to programming (l/l).No.SymbolDescription0010#4PRG9Editing of subprograms from 09000 to 09999 is not inhibited/is inhibited.0011#6GO1The mode selected at power-on is GOO/GOl.0015#7CPRDIf a decimal point is omitted, the selected unit is the least input increment/mm, inch,de...

  • Page 20

    (13) Parameters related to spindle control (l/2)No.SymbolDescription0003#5GSTBy SCR (G120, #5), spindle orientation is executed/a gear-change is executed.0012#6G84SIf the G74 or G84 cycle is specified, the gear is changed at a point specified through Sanalog output gearshange method A or B/at a p...

  • Page 21

    (13) Parameters related to spindle control (2/2)No.ISymbol 1Description0556 1-w-c-- I Maximum spindle speed for the constant surface speed control function~~ _. ~~ ___ ~~0576 ---_-- Permissible error in the number of error pulses between two spindles in the mode of(simple) synchronous control of ...

  • Page 22

    (15) Parameters related to canned cycles (1 /I)INo.1 Symbol 1Description1 0002#4, #5 1PMXYI , 21 Axis and direction on and in which the tool is retracted in canned cycle G76 or G870011#4MCFWhen positioning of G81 terminates, the signal to specify an external operation func-tion is not output/is o...

  • Page 23

    116)Parameters related to rigid tapping (2/2)No.1 Symbol 1Description0388#3 1RGORT 1 When rigid tapping is started, a spindle reference position return is not made/is made.- ?I388#5 1SIG [ At a gear-change, the SIND signal is disabled/enabled.~_~ _0388#6CHKERCDuring spindle rotation, the position...

  • Page 24

    (17) Parameters related to scaling and coordinate system rotation (l/l)No,ISymbol 1Description0036#0to #2 [SCL*l Scaling for each axis is disabled/enabled.0036#7 1SCR 1 The unit of scaling magnification is O.OOOOl/O.OOl .0041 #ORINAn angle of coordinate system rotation is always specified in the ...

  • Page 25

    121)Parameters related to custom macro (l/I)No.1 Symbol 1DescriptionI0011#5 1SBKM1 By a macro statement, a single-block stop is not made/is made.I0040#1DPOSUPIf data is output by the DPRINT command, leading zeros are output as space charac-ters/as they are.I-- 0040#5 )TMCR1 A T code is processed ...

  • Page 26

    (23) Parameters related to graphic display (l/l)No.0046#50058#00058#1SymbolDescriptionGRPOSOn the screen of a solid drawing or tool path drawing, the current position is not dis-played/is displayed.SGORGIf the coordinate system is changed during drawing, drawing is executed on the samecoordinate ...

  • Page 27

    (25) Parameters related to tool life management (l/l)INo.1 Symbol 1Description1 0039#0, #I 1GST*1 Number of tool groups that can be registered0039#2 1LCTM1 The tool life is specified in terms of the number of times used/time period.0039#3TLSKIf the tool skip signal TLSKP (G140, #0) is input, the ...

  • Page 28

    (28) Parameters related to the software operator’s panel (l/l )0017#0 1OPGl0017#1 1OPG20017#2OPG3‘OPG40017#4OPG50017#5 1OPG6-~0017#6 1OPG7013005137 1 ------0140 to0203 ( ------DescriptionOn the software operator’s panel, the mode is not selected/is selected.On the software operator’s pane...

  • Page 29

    131)Parameters related to PMC axis control (1 /I)No.1 Symbol 1Description----3024#0~IGNPMvaxis control is enabled/disabled._~0030#0, #I 1EAC* ( Axis setting for executing PMC axis control (specification A)0032#47032#4PNGMLKOn a PMC axis, a machine lock is enabled/disabled.PNGMLKS0032#6 1EACSB 1 P...

  • Page 30

    (32) Parameters related to the surface grinding machine (slanted axis control) (l/l)No.SymbolDescription0077#4ZRTMlWhen a manual reference position return is performed on the Y-axis, movement oc-curs on the Z-axis/does not occur on the Z-axis.0077#5AGLSTSlanted axis control is not executed/is exe...

  • Page 31

    :36) Parameters related to the DNo.1 SymbolDescription0390#7 1NODC3During DNC operation, reading is executed for each block/until the buffer is filled.0320 1 ------Time-out period of the no-response timer0321 ( ------Time-out period of the EOT signal timer0323 1 ------0324 1. -.i----0325 _-_---l0...

  • Page 32

    Setting parameter[SETTING I](1) REVX:REVY:Specify whether to enable a mirror image for the X/Y-axis.1: Enable0: DisableNote) If a mirror image is enabled for an axis, the movement of the axis is reversed during automatic operation except for amovement from the middle point to the reference positi...

  • Page 33

    [SETTING 21(8)PWE: ’ Specifies whether to enable parameter writing.1: Enables.0: Disables.(9)REV4:Specifies whether to enable a mirror image for the fourth axis.1: Enable0: Disable(IO) TAPEF:Specifies the type of a tape format.1:Fl O/F1 1 format after conversion0:FSO standard format without con...

  • Page 34

    Parameter description[Ol. Setting method]1) Preparation(A) Select the MDI mode.(B) Press the function button [DGNOS/PARAM] to display the parameter setting screen.(C) Key in address “No.” and value “0” in the stated order, then press the [INPUTJ button; the setting parameter screen willap...

  • Page 35

    [03. Cautions]1) If a parameter with “POWER OFF” is rewritten, the P/S 000 alarm (turn off the power) occurs. In this case, it is necessaryto turn off the power. This also applies when the programmable parameter input (GIO) function is used to rewrite theparameter.2) Always set undefined para...

  • Page 36

    c00017RDRNDECIIOFRS43DCSPRODsew,6543210RDRNDECIIOFRS43DCSPRODsew1:0:1:0:1:0:1:0:1:0:Dry run is effective for rapid traverse.Dry run is not effective for rapidtraverse.Decelaration signal “ 1” in refernce pointreturn indicates deceleration.Decelaration signal “0” . in refernce pointreturn ...

  • Page 37

    STP2 1:In the reader / puncher interface, the stop bitis set by 2 bits.0:In the reader / puncher interface, the stop bitis set by 1 bit.(Effective when the setting paramerter I /O is0.)(Note)The band rate is set by parameter No.0552.r-l0003HSLE1 LCPGSTOVRIZM4ZMZZMYZMX7G543210PSG2, 1 Gear ratio of...

  • Page 38

    DMRX to DMR4 Setting of detective multiplierSetting codeDetective multiplier654Analog servoDigital servo000l/21 I20011101013/20 1 11 0 01 0 11 1 01 1 1223/2 ’5/23327/244GRDX to GRD4 Capacity of reference counterSetting codeCapacity of reference counterAnalog servoExcept for 0.1 ,U0.1 ,U detecto...

  • Page 39

    Relationship among DMR, CMR and GRD. (In case of System series M)Metric systemMoving distanceCountingper 1 revolution(detectionof motorunit)(Pulse coder)(pm)12 mm1IO mm18mm16 mm15 mm14mm13 mm12 mm11 mm0.5CommandDetect multiplyCapacity ofmultiplyratio (DMR)referenceratioPulsePulsePulsecounter(CMR)...

  • Page 40

    0008EILK OTZN ROVE ADW2 ADWi ADWO,76543210EILK 1:interlock is performed for each axis.(FANUCPMC-MODEL Lisnecessary.)0: interlock is performed for all axesor for Z axis only(it needs that No. 012 ZILK = 1).OTZN 1:Z axis stored strok check is notFIN signal is ignored, because X < TFINdone.0: Z a...

  • Page 41

    l-l0010APRSPRG9OFFVY EBCLISOT76543210APRS 1:Automatic coordinate system settingis conductedwhen manual reference point returnis perfomed.0: Automatic coordinate system settingis notconducted.,PRG9 1:The subprograms withprogramnumber9000to9999areprotected.Thefoilowingeditfunction are disabled.(1)(...

  • Page 42

    ADNW 1:Select B type for feed rate.0: Select A type for feed rate.(A type)(1) JOG feed rateJOG feed rate of additional (rotary)axis is the same as that of basicaxes (X, Y, Z).(2) Cutting feed upper limit feed’ rateTangential speed is clamped atparameter value for all axis.(B type)(1)(2)(3)(4)AD...

  • Page 43

    FXCS 1:0:ASR33 1:0:ZILK 1:0:RemarksSTP2 1:0:In canned cycleG74 or G84, spindleCW/CCW rotatioin is performed without MO5code output.In canned cycle G74 or G84, spindle CW /CCW rotation is performed after MO5 signaloutput.The 20mA current interface is used as thereader / puncher interface.FANUC PRR...

  • Page 44

    1:The cursor does not blink.0PG31:0:The cursor blinks.0016,NPRD SUPM0:532NPRD1:Input and display with dicimal point isOPG2 I:ineffective.0:Input and display with decimal point iseffective.0:1:Start-up Btype is effec-tive in cuttercompensation C.OPGl1:0:Start-up Atypeiseffectivecompensation C.For ...

  • Page 45

    NXMP2,. NYMP2, NZMP2, NZMP4MHPGB1: Multi-handle function is specification B.1: Handle feedmagnificaitonxl 00is0: Multi-handle function is specification A.ineffective for X, Y, Z and 4th axes,(For specification A/B, see connectingrespectively.manual.0: Handle feed magnification xl 00 is effectivef...

  • Page 46

    ABSX, Y, Z, 4, 7, 8INOUT1: Reference point position in absolute pulsecoder is settled.0: Reference point position in absolute pulsecoder is not settled.(It is automatically set to “1” whenmanualreference point return is executed.Do notchangethesettingwithoutchanging the detector.)Set 0 withou...

  • Page 47

    MMDL 1:0:DACTF 1:0:PRCMSG 1:0:PRCPOS 1:0:l-l0029Modal status is displayedinMDIoperation B.Modal status is not displayed in MDIoperation B.Actual speed is displayed on the currentpositon display screen and program checkscreen.Not displayed.On the program check screen, a messagefrom PMC is displaye...

  • Page 48

    LGCM 1:0:Low - and high- speed gear changingspeedrpmdepends onparameterSPDMXL (No. 585). When gear 3 - stepis used, low and medium - speed gears,and medium - andhigh- speed gearschanging speed on parameter SPDMXL(No. 585) and SPDMXH (No. 586).Gear changing speed rpm shall be therespective maximum...

  • Page 49

    No.Parameter*ContentsI RSCMD3 DEVFL3III/O device to be usedI 0I 0I Bubble cassette, PPRI05040505050605070508050905100511SERRX (X) Limitation value of position.deviationamountduringmovement of X axis.SERRT (Z) Limitation value of pdousz,o;deviationamountmovement of Y (Z) axis.SERRZ (3)Limitation v...

  • Page 50

    LCTM1: Designates the tool life by time.0: Designates the tool life by frequency.GSTl/GST2:Designate the number of registerable groups intool group setting.I IGST2 GSTlNo. of groups INo. of tools/groupI2 1 I 1 l- 16 1 l-16 t001 - 321-8011 -641-41 1 0 1 l-128 I l- 2 I76 5 4 3 2 1 00040LOCC COMC TM...

  • Page 51

    LSUP 1:rl0042ASTCD76 5 4 3 2 101OG43cEQCD j--j---~-.1SHPCDASTCD, EQCD, SHPCD:Set ihe hole pattern of *, =, # of EIA codes incustom macro B in sequence, using El-bit data.00454HSIFCLERCCINP Lsuf’ RWDCU RALRDL7HSIFCLERCCINP61:0:1:0:1:0:5 43 2 10M/S/T/B code processing shall be a high-speed interf...

  • Page 52

    NPRV 1:0:EFMLlO 1:0:S3JOG 1:0:RDIK1:0:DILK1:0:rl0050The each axis interlock signal shall be valid,only in manual operation.The each axis interlock signal shall be invalid.4NFEDRSASCISTP276543210Even when no position coder is provided, theper-revolution feed command shall be valid.(The per-revolut...

  • Page 53

    NODIC 1:0:l-l0053The current position display of PMC axiscontrol shall be the same as in standardspecifications, not in accordance with thedecimal point position of increment systeml/10.The current position display of PMC axiscontrol is in accordance with the decimalpoint position of increment sy...

  • Page 54

    MSKT1: At interruption, an absolute coordinate is setto a skip coordinate.0: At interruption, an absolute coordinate is notset to a skip coordinate.0057,MBCLRFXYHOT3 CROUTMICb.76543210MBCLR1: MDI-B program is cleared by the resetFXY1:HOT31:CROUTIn B/D PRINT, after the data is outputted in IS0MIC0...

  • Page 55

    EDPX,EDPY,EDPZADLIN7,ADLIN8For the command in the plus direction of X, YThis sets the linear axis/rotary axis of 7th and 8thand Z axes :axes.1: External deceleration is valid for rapidtraverse and cutting feed.0: External deceleration is valid only for rapidtraverse.1: Rotary axis0: Linear axisC8...

  • Page 56

    VALPC 1:0:(Note)M198PPRSTINI:MTDSPIr-l00641:0:Optional gear ratio is used between thespindle and the position coder in rigid tapping.Optional gear ratio is not used between thespindle and the position coder in rigid tapping.When VALPC = 1, the optional gear ratiobetween the spindle and the positi...

  • Page 57

    0101r-l0108CMRY176543210SPLOWSpindle speed during constant speed spindlerotation, or spindle speed at gear shift. (when0102parameter No. 0003, GST = 1 ),CMRZ7654321010103Setting value =speed at gear shiftx 4095Max. motor speedCMR4c76543210CMRX, CMRY, CMRZ, CMR4 :Command multiply for X, Y, Z and 4...

  • Page 58

    I0117IH4NO + HZNO1HZNOIn case of multi-handle B specification, whichmanual pulse generator is used for the Z axis isspecified.Setting value:12to32H4NOIn case of multi-handle B specifi-cation, whichmanual pulse generator is used for the 4th axis isspecified.Setting value: 12 to 32Setting method2nd...

  • Page 59

    (Example) When setting t to + X, 4 to-X, -+ to + Z and0135+- to - Z, set as follows.UPKY=l,DWNKY = 2,RGTKY = 3,BACKYLFTKY = 4,b) In case of M seriesSpecify the JOG move axis and direction on thesoftware operator’s panel corresponding to keys.r, 5-t-5 +, J,YURKY to LTUKYSet the jog feed axes and...

  • Page 60

    The names of general purpose switches (SIGNAL 0- SIGNAL 7) on the software operator’s panel in thefollowing figure are set as follows.OPERATOR’ S PANEL 01234 N5678SIGNAL0 :H OFF ONSIGNAL1 :OFFHONSIGNAL2 :OFFmONSIGNAL3 :n OFF ONSIGNAL4 :HOFF ONSIGNAL5 :HOFF ONSIGNAL6 :IOFF ONSIGNAL7 :AUTOChara...

  • Page 61

    Character-to-codes Correspondence TableCharacterCodeCommentCharacterCodeCommentA0656054B0667055C0678056D0689057E069032SpaceF070!033 .Exclamation markG071II034Quotation markH072#035SharpI073$036Dollar symbolJ074%037PercentK075&038AmpersandL0769039ApostropheM077(040Left parenthesisN078>041Ri...

  • Page 62

    r-l02040214POSTN 1l-l0205POSTN20206POSTN3r-l0207POSTN411POSTNl to 4Approach amount for single direction positioningof X-axis, Y-axis, Z-axis and 4th axis Settingvalue : 0 to 255 Unit 0.01 mm (metric output)Setting value : 0 to 255 Unit 0.001 inch(inchoutput)(Note)In increment system l/l 0, the un...

  • Page 63

    MCDCNTr-l0220When the preset M code is executed, thetotal number of machined parts and thenumber of machined parts are counted.Setting value: 1 to 255(0 is equivalent tono setting.98 and 99cannot be set.)r-l0229UMGCDSISet up to 10 G codes calling custom macro.UMGCDO:UMGCDl:UMGCD2:UMGCD3:UMGCD4:UM...

  • Page 64

    0247MACRETMACRET:M-code to disable custom macro inter-ruption.Set value: 0 - 2550248M198MM198M:M-code to call the program registered in aprogram by the method other than Ml 98.Set value: 1 - 255(Note)When the set value is 0, it is equivalent to nosetting.10250BRATE2,..0251BRATE3BRATE2:BRATE3:Baud...

  • Page 65

    r-l0256SVAXZSVAX4SVAX7SVAX8Set the servo axis number to output the 3(Z)-axis command.Set the servo axis number to output the 4thaxis command.Set the servo axis number to output the 7thaxis command.Set the servo axis number to output the 8thaxis command.Setting value 1 to 6.IMCODEIPOFFMCODE:M-code...

  • Page 66

    cc 0269 0270 0271 Set Value 4 3 1(The X axis is the high speed axis, SO 2cannot be set.)0275CMR70276CMR8,CMR7, CMR8:Set the command multiply of the 7th and 8thaxes, respectively.Remarks:Refer to the parameter Nos. 0100 - 0130.0279PSELP4PSELP4:Y 90285DPAX7M code for counting the number of times th...

  • Page 67

    (Example) When TLCSAM = 0Tape formatP004L0500 ;TO101 ;TO105 ;TO108 ;TO206 ;TO203 ;TO202 ;TO209 ;TO304 ;TO309 ;POO5L1200 ;TO405 ;Meaning1(1)1(2)3 (3)Tools having the same tool numberin group 4 are used 500 times orfor 500 minutes in total along theprogram steps group (1) to (3).When the group is s...

  • Page 68

    SERRX, SERRY, SERRZ, SERR4(1)Limitation value of position deviation amountduringmovement for X, Y, Z and 4th axis,respectively.Setting range: 0 to 32767 (detection unit)(Example) When’ the rapid traverse rate is 10 m/min.and the position gain is 30, the error iscalculated by: Conversion of 10 m...

  • Page 69

    r-l0516l-l0521PSANGNS4/S5 digits control (Analog output)PSANGNSets the data for adjusting the gain of analogouptut.Setting range: 700 to 1250Standard settingvalue : 1000(Adjusting method)(1)Set the standard setting value 1000.(2) Designate the maximum S analog value(1 OV).(3)Measure the output vo...

  • Page 70

    10529FEEDT*FEEDTTime constant of the exponentialacceleration/deceleration in cutting feed andjog feed.Setting range:0 to 4000 unit: msec Set this to “O”, whenthe exponential acceleration/ deceleration isnot used.0530FEDFLFEDFLThe lowerfeed rate in exponentialacceleration/deceleration.Setting ...

  • Page 71

    q Spindle speed A with low gear when the commandvoltage is 10 V (parameter No. 541). Spindle speed B with high (or middle) gear when the(Note 1) Unit becomes 1 /lO in increment system 1 /lo.(Note 2) Set a backlash compensation value with adetection unit when an arbitrary commandmultiply is used.S...

  • Page 72

    rl0543l-l0548SPDMIN / GRMX4IGRMXl to4GRHMINGRLMAXSPDMAXThe spindle speed cone-sponding to gears 1to 4 when the spindle speed command is1 OV.(for constant surface speed control)Setting range: 1 to 19999 (unit: rpm)Setting of the lower limit of the spindle speedwhen using high speed gear. (middle s...

  • Page 73

    l-l0552r-l0555IBRATEOIBRATE 0This sets the baud rate when thereader/puncher interface is used.(Effective when the setting parameter I/O is0.)Relation between the setting value and thebaud rate is as follows:Baud rate501001101502003006001200240048009600rl0553IBRATElIBRATElThis sets the baud rate w...

  • Page 74

    if AX <CRCDL and AZ (AY) < CRCDL,(Note)the smallmovement is ignored. This preventsthe workpiece from being affected by stoppingthe tool at the corner.r-l0559RPDJXr-l0560RPDJY0561RPDJZrl0562RPDJ4(Note 1)(Note 2)If “0” is set to these parameters, the setvalues of parameter No. 0518, 0519,...

  • Page 75

    l-l0567IFEDMADFEDMADUpper limit of feed rate of all axes in case offeed rate 6 specification.Setting range:6 to 15000 unit: deg/min (rotary axis)6 to 15000 unit: mm/min (mm output)6 to 600 unit: inch/min (inch output)(Note)In increment system 1 /I 0, unit is the same.I0568IRPDFLADIRPDFLADLow spee...

  • Page 76

    r-l0586SPDMXHSPDMXHSets the spindle motor speed rpm at the timeof medium- and high-speed gear changewhen 3-step gears are used.Spindle changing speedSetting value =x 4095Spindle max. speedSetting value: 1 to 40950589PSGSPR0590PSGSPLL-G-lPSGSPBSet the escape value (d) during deep hole drilling in ...

  • Page 77

    rl0599r-l0607TLCNEGIPFLJGZTLCNEGr-l0600Tool life management ignore No.Setting value : 0 to 9999PARTRQr-l0601Sets the number of machined parts required.Setting value : 0 to 9999PEXPJXl-l0602PEXPJYI0603PEXPJ3I-ET-lPEXPJ4PEXPJX- PEXPJ4Sets exponential acceleration/decelerationr-l0605time constant se...

  • Page 78

    SFttSFttNote)ITPSMXii?z5f=FDTTPFBS____TPSMXStandard threadI fKeep the inclination of theacceleration/deceleration.Actual timeconstantF-_-mmSActual leadBecauses the time constant is produced byproportional calculation even in the case ofexponential-type aceleration/deceleration, there willbe a sma...

  • Page 79

    LPGMSLoop gain multiplier of the spindle in the rigidtapping for the high speed range. This has alarge influence upon the thread accuracy.Make fine adjustment to obtain the optimumvalue by performing the cutting test andmatching with the loop gain.Data type: Word typeSet value: 1 - 32767Set value...

  • Page 80

    rl0620l-l0622ITPESZTPERZTPERZ: Limit value of position deviation during movement ofZ axis in the rigid tapping modeData type: Word typeSet value: 0 - 32767Unit: Detection unitWhen a one-tenth resolution detector is used, theunit becomes ten times the detection unit.I I0621TPERSTPERSLimit value of...

  • Page 81

    Position \r-l0625EL@La=1.667 [V] (motor of 6000rpm at 10 [V] )=720°(Spindle is rotated one turn byone spindle motor rotation.)= La/4096= 720”/4096 = 0.17578’=720”(Spindle must make two rotations= 360” x 2 for rotating the positioncoder one turn.)4096 =Detection pulse perposition coder ro...

  • Page 82

    0635PLNTC.PLNTC?0636Set the time constant of linear acceleration/deceleration after interpolation of cutting feedfor all axes.When the set value is 0, theacceleration/deceleration type is exponential.Set value: 8 - 1024 Unit: msec9PEXDECPEXDECExternal deceleration speed (command to allaxes).Set v...

  • Page 83

    0649 1r-l0657ISTPE7PEAFLX1 0650 11 0658 1STPE8PEAFLYSTPE7, STPE8Position deviation limit values in stop of7th and 8th axes.Set value: 0 - 32767Detection unitl-l0651PEFDTX1 0652 1PEFDTY0659cPEAFLZ0660PEAFL4r-l0661PEAFL70653PEFDTZ0662PEAFL80654PEFDT4PEAFLX - 8Lower limit speeds (FL) at exponentiala...

  • Page 84

    ,0664GRPMDlGRPMDSet the number of teeth of the 2nd stage gearin the spindle when the gear ratio is optionalin the rigid tapping mode.Data type: WordSet value: 1 - 327679(Note)Valid when VALPC (parameter No.63) = 1.0665GRPHI1-GRPHISet the number of teeth of the 3rd stage gearin the spindle when th...

  • Page 85

    l-l0671TPLGHTPLGHLoop gain for position control of the spindleand Z- axis of each gear in the rigid tappingmode. Set the position control loop gain ofthe 3rd stage gear.Data type: WordSet value: 1 - 9999Unit: 0.01 msec-1rl0700ILTlXlIl-l0701-- -LTlYIII-E-lILTl ZIIrl0703ILTl41Il-l0704LTl X2Il-l0705...

  • Page 86

    Example) LTl Zl = -1 and LTlZ2 = 1the Z axis stroke becomes infinite.I I0714(Note 1) For the axis whose stroke is infinite, theincremental command can be specified. If theabsolute command is specified, the absoluteregister may overflow and it is not operatednormally.(Note 2) These parameters cann...

  • Page 87

    r-l0733l-l0740PSCRT3IABSYPPSCRT2, PSCRT3Set the magnifications of Y and Z axes whenthe magnify command is not specified inscaling.Set value: + 1 - + 99999Unit:0.001 magnification0.00001 magnification(Note)When PRM No.63 bit 6 ESCAL = 1 (mirrorimage, each axis scaling is valid), be sure toset a va...

  • Page 88

    r-l0749LT2Z2l-l0750ILT242ILT2Xl U-242Check stroke limit using these parameters,not parameter Nos. 0700 to 0707 whenEXLM2 (G129.6) signal is ON.(Note)Valid only when parameter No. 915LM2 = 1.r-l0751ILT2X2IL-l-2 clclII Apex No. of square areaRepressnts the axisSet the stroke limit represented above...

  • Page 89

    rl0760IZOF2S2II I0761IZOF2S3Irl0762IZoF2S4IZOFISI to 42nd work zero-point offset amount of X-axis,Y-axis, Z-axis and 4th axis in sequence.(G55)Setting value: 0 to + 99999999Unit 0.001 mm (Metric output)0 to +99999999Unit 0.0001 inch (inch output)Normally, data are inputted from the workcoordinate...

  • Page 90

    ZOF5S1 to 4(Note)rl07755th work zero-point offset amount of X-axis,Y-axis, Z-axis and 4th axis in sequence.(G58)Setting value :0 to If: 99999999Unit 0.001 mm (Metric input)0 to + 99999999Unit 0.0001 inch (Inch input)Normally, data are input from the workcoordinate system setting screen.Unit becom...

  • Page 91

    REF4X -REF44Sets distance of 4th reference point on X axisto 4th axis from 1st reference pointFlDFl to 9Feedrate for Fl digit commands Fl to F9 insequenceSetting value :I-l07990 - 15000 Unit: 0.1 mm/min (Metric output)0 - 6000 Unit: 0.1 inchlmin (Inch output)When the manual pulse generator is rot...

  • Page 92

    l-l0822u-3 III1I Number of the vertex of square area..ILT181- indicates an axis.Set the stroke limit indicated by the above.r-l0823Set value: 0 - + 99999999Unit: 0.001 mm (metric output)Set value: 0 - + 99999999ILT172IUnit: 0.0001 inch (inch output)Set by the distance from the reference point.Whe...

  • Page 93

    Setting of pitch error compensa-tion amountfor Z axis. (for M series), 3rd axis (for Tseries)Setting range : 0 to + 7.ABS8PABS7P, ABS8PCounter data values at the reference pointreturn position when the absolute pulse coderis used. This value is automatically set at thecompletion of manual referen...

  • Page 94

    70017005DECISsewsL7654321076DECIS1:Machine decelerates when decelerationsignal is 1 inreference point return.0:Machine decelerates when decelerationDMR6GRD6DMR5, DMR6signal is 0 in reference point return.GRDS, GRD6sews1:Minimum command increment is theinch system (Machine inch system).0:Minimum c...

  • Page 95

    PMLlSPML2SMultiplier00Xl01x210x411x8,,7021SUB1APC6APC57654321APC5/APC6 1:When the absolute pulse coderis mounted for 5th/6th axes.0:When the absolute pulse coderis not mounted for 5th/ 6th axes .SUB11:PMC axis control is the 5th axis.10detectordetector0:PMC axis control is the 5th/6th axes.v7022A...

  • Page 96

    I I7130r-l7508IDSPSUBIIGRDSSII’7131r-l7509DSPSUB2GRDSGIDSPSUBI, 2 Set the axis names of the 5th/6th axes insequence.The setting code shall be in accordance withthe general switch code on the operator’spanel. Usable characters:(X, Y, Z, U, V, W, A, B, C, H, 0 - 9, 0, N D,-94(Note)When displayi...

  • Page 97

    r-l7522rLINT5Ir-l7523ILINT6ILINTS, 6Time constant of liner acceleration anddeceleration for 5th/6th axes respectively.l-l7529IFEEDTSIFEEDTSTime constant of cutting feed exponentialacceleration/deceleration (5th/6th axes incommon.)rl7530r--FEDFLSIIZRNFLSIZRNFLSLow feedrate at reference point retur...

  • Page 98

    El17658EAFLGEAFLGCutting feed exponential acceleration/decelerationlowerLimit speed (FL) in orderSetting value :0.6-l 5000Unit :mm/min (mm outupt)Setting value : 0.6-6000Unit:0.1 inch/min (inch output)However, when 0 is set the value becomesNo.7530.I I7700LTI 51cLTI 61r-l7704ILTI 52Irl7705LTI 62L...

  • Page 99

    In the following, parameter numbers of each axis are to beindicated by*.r-l8000DGPRM76 5 4 3 2 10DGPRM While the power is turned on, the standardvalues of parameters related to Digital Servo are0: to be set1: not to be setWhen this parameter is set to 0 after setting themotor type, the standard v...

  • Page 100

    8021Load inertia ratio (LDINT)Parameter inputData type: Word axis typeData unitData range: 1 to 32767When Digital Servo is to be used, calculate the inertia ratioof the load inertia and motor rotor inertia according to thefollowing expression and setit for each axis.Load inertia ratio =Load inert...

  • Page 101

    Parameters which can be determined byn the motor to be applied.(Data type: Word axis type) (1)Parameter .AC servo motor to be appliedNo.5-O4-o3-o2-o1-o0.80402414606693224698288041-527-1461-2126-1103-1625-27828042-1873-2373-2374-2488-2503-2457804380104962672172268044-300-517-477-1330-1082-11278045...

  • Page 102

    Parameters which can be determined by the motor to be applied.(Data type: Word axis type) (2)ParameterAC servo motor to be appliedNo.51020M203030RSC1401720944808997014527058041-2781-3532-3074-3682-5576-27168042-3052-2622-2649-2646-2665-266980433596548245355-56748044-1789-3259-4103-2666-2516-33568...

  • Page 103

    Common parameters for each motor model(Data type: bit axis type)ParameterIDataNo.if7 #6 #5 #4 #3 #2 #l #080030000000I8004000110’10- 99 -

  • Page 104

    Table 1. Relation between override signal and manual constant feed rateI Condition of contact onParameter OVRI = 1IParameter OVRI = 0the machineManual constantManual constantOverridefeedrateOverridefeedrate“0V8valueMMINCHvalueMMINCHseriesseriesseriesseries0%Omm/Oinch/150%1260mm/ fjOinch/minminm...

  • Page 105

    Table. 2Condition of rotary switchManual constant feedratelPositionParameter OVRI=OParameter OVRl= 1MM InputINCH Output“OV8“OV4“OV2*ov1*OV8“OV4“OV2*ov1MM InputINCH inputMM OutputINCH Output00 000Omm/minOinch/minOmm/minOinch/min10 0 00IO0.4251.020lolol 101 14 I 0.5 ( 35 I 1.4 I3...O. OrO...

  • Page 106

    Table. 3Condition of rotary switchManualParameter OVRI = 0Parameter OVRI = 1Positionconstant*0V8*ov4*ov2"OVl*0V8*ov4*ov2*ov1feedrate>00Odeg/min001000l14\I00c100200I*3000020400I 0 I 0 I‘5000037IIIIIII1III60 0005270 0 0 072800 0 01009000 0140q100000120011100 00270120 00 0370130 000520140 ...

  • Page 107

    Table 4ICondition of rotary switchParameterManual constantfeedratePositionParameter OVRI = 0Parameter OVRI = 1(PSU/min)*OV8 “OV4 “OV2 “OVI*OV8 “OV4 *OV2 *OVl00-00-0010(_3010_0_2000014300L9101 I I120-\lot000275000037IOlOl005270000728000010090’000140100000-2001100002701200OlOl370I1300.005...

  • Page 108

    Specifications of Additional Parameters.l This document is a description of the additional parameter applied in FANUC SeriesO-MC 0466/20 or later. Therefore, some parameters might not be applied in otherseries/edition.l Because the specification might be limited, please refer to each specificatio...

  • Page 109

    #7#6#5X4# 3#2#1#O,NO. 0002RSASC I1 :0 :1 :0 :1 :0 :RSASC I1 : ASCII code is used for reader/puncher interface.0 : ISO/EIA code is used for reader/puncher interface.(Note) This parameter is valid only when I/O on (SETTING 1) is set to “0”.1 :0 :1 :0 :1 :0 :1 :0 :NO. 0010EXOPE#7#6#5LEXOPE1 :0 :...

  • Page 110

    1 :0 :x7# 6#5#4# 3#2Xl#ClNO. 0012RSASC I1 :0 :1 :0 :1 :0 :RSASC I1 : ASCII code is used for reader/puncher interface.0 : ISO/EIA code is used for reader/puncher interface.(Note) This parameter is valid only when I/O on (SETTING 1) is set to “1”.1 :0 :1 :0 :1 :0 :1 :0 :#7#6#5#4#3#2111#ONO. 001...

  • Page 111

    1 :0 :#7#6x5#1#ONO. 0021NOFLUP(Note) It is necessary to turn off CNC power after changing these parameters.1 :0 :1 :0 :1 :0 :1 :0 :1 .OI1 :0 :NOFLUP When equipping absolute pulse coder,1 .: there is no coordinate running without axes motion at initial power-up.0 : there is coordinate running with...

  • Page 112

    1 :0 :1 :0 :#7#6#5#4#3#i2#l#ONO. 0030AXS4DLCDOFCDH(Note) It is necessary to turn off CNC power after changing these parameters.1 :0 :1 :0 :OFCDH1 : Tool offset memory C is used.0 : Tool offset memory C is not used.(Note) It is necessary to set parameter 036#6 (OFRD) to “1” when this parameter...

  • Page 113

    TYPE21 : The master printed circuit board is a high-speed master printed circuitboard (type 2).0 : The master printed circuit board is a normal master printed circuit board.(Note) This parameter is used for self-diagnosis. It does not have to be set by theuser.1 :0 :NOPCAL1 : If a PC alarm (600 t...

  • Page 114

    1 :0 :1 :0 :RGTPENO. 0046BGRELWhen releasing rigid tapping mode,1 : rigid tapping signal (RGTAP/RGTPN) off is not checked.0 : rigid tapping signal (RGTAP/RGTPN) off is checked.1 :0 :1 :0 :1 :0 :1 :0 :1 :0 :#7#6x5#4#3112#l#OBGREL1 :0 :1 :0 :1 :0 :1 :0 :When the amount of part program storage is 12...

  • Page 115

    #5#4#3#l#ONO. 0047ZSSTP8ZSSTP7ZSSTP4ZSSTP3ZSSTPZZSSTPlZSSTPlZSSTP2ZSSTP3ZSSTP4ZSSTP7ZSSTP81 : The single-revolution signal for the servo motor is input from theseparate pulse coder interface.0 : The single-revolution signal for the servo motor is input from the built-in pulse coder interface.1 :0...

  • Page 116

    #7#G#5#4#3#Z#1#ONO. 0050NOFMK1 :0 :NOFMK1 : Tape format check is not done during sequence No. search.0 : Tape format check is done during sequence No. search.1 :0 :1 :0 :1 :0 :1 :0 :1 :0 :1 .OINO. 0056NOCNDNOCNDWhen equipping tape storage memory 120/320m or back-ground edit,1 : condensing part pr...

  • Page 117

    NO. 0057x7#6#5#4#3#2#1SALNCALMNC#OPWNNCPWNNC1 : CNC screen is displayed after CNC power-up.0 : MMC screen is displayed after CNC power-up.(Note) This parameter is valid on 00-MC.ALMNC1 : Screen changes to CNC screen automatically when CNC alarm happens indisplaying MMC screen.0 : Screen stays in ...

  • Page 118

    OPMNDP1 : Operating monitor display is valid.0 : Operating monitor display is invalid.EXTSP1 : Program No.search and display are valid for the protected part programs byparameter PRGS.0 : Program No.search and display are inhibited for the protected partprograms by parameter PRG9.1 :0 :NO. 0062#7...

  • Page 119

    I OMDGN1 : Signals of I/O link and expanded R/D data are displayed on DGN screen.0 : Signals of I/O link and expanded R/D data are not displayed on DGN screen.1 .0:1 :0 :1 :0 :1 :0 :NO. 0065#7#6#5TAPDRN#4#3PSOT#2#l#OCZRN1 :0 :CZRNWhen using Cs contouring control of serial interface spindle,1 : G2...

  • Page 120

    NBD78When using Cs axis control or Cs contouring control,1 : 7th or 8th axis control is valid in spite of 4th or ‘7th axis control PCB.0 : number of control axes is same as axis control PCB.1 :0 :EPMSKP1 : Skip signal for PMC axis control is independent of CNC skip signal.0 : Skip signal for PM...

  • Page 121

    NO. 0071#7X6FSRSPDPCRAM#5 . #4SRLZSP#3#2#lX0I SRLPC(Note) It is necessary to turn off CNC power after changing these parameters.I SRLPC1 : Position coder cable is connected to M27 on memory PCB when using serialinterface spindle.0 : Position coder cable is connected to spindle amplifier when usin...

  • Page 122

    1 :0 :1 :0 :1 :0 :1 :0 :#7#6x5#4#3#2#l#ONO. 0075I ONULI NHNDSYNMlSYNMO .SYNMl SYNMO Master axis of simple synchronization of feed axisNo synchronizationX-axis(4th-axis is synchronized with X-axis. >10Y-axis(4th-axis is synchronized with Y-axis. >11Z-axis($th-axis is synchronized with Z-axis...

  • Page 123

    JZRN1 : Dogless reference point return is effective. (Note)0 : Dogless reference point return is ineffective.(Note)This parameter is applied to all axes. To set each axis individually, set thisparameter to 1, then set bits 0 to 5 of parameter No. 0391 as required.IOP1 : Soft-key “STOP” interr...

  • Page 124

    #7#6#5#4#3112#l#ONO. 0078EAXOVERDRNEOVRIENOINWZNOINMVNOINOGNO I NOWNO I NOWNOINOGNOINMVNO I NW2OVRIE1 : Changing wear offset values by using MD1 key is prohibited.0 : Changing wear offset values by using MD1 key is allowed.1 : Changing geometry offset values by using MD1 key is prohibited.0 : Cha...

  • Page 125

    1 :0 :1 :0 :IXTYP1 : The sequence of table index is type-B.0 : The sequence of table index is type-A.#7#6#5#4#3#2#1#ONO. 0080SPZNEGSPlNEG _MORCM2MORCMl(Note) It is necessary to turn off CNC power after changing these parameters.1 :0 :1 :0 :MORCMl1 : Spindle orientation whose position is specified...

  • Page 126

    KEY OGKEYMVKEYWZKEYPRMTCHK1 : The geometry offset protection state is based on program protection signalKEY <G122#3>.0 : The geometry offset protection state is based on bit 1 (NOINOG) ofparameter No. 0078.1 : The macro variable protection state is based on program protection signalKEY <...

  • Page 127

    x7#6#5#4#3x2#l#Ov1NO. 0387EFERPDSQDNC4SQDNC1 : Program restart is effective not only memory operation but DNC operation.0 : Program restart is effective only for memory operation.1 :0 :1 :0 :1 :0 :1 :0 :1 :0 :1 :0 :EFERPD1 : Rapid traverse rate for PMC axis control is specified in feedrate comman...

  • Page 128

    1 .OI#7#6#5#4#3#Z#l#ONO. 0389EADSLPRG8SPPRMSRVSET(Note) It is necessary to turn off CNC power after changing these parameters.SRVSET1 : Servo tuning/setting screen is not displayed.0 : Servo tuning/setting screen is displayed.SPPRM1 : The spindle adjustment screen is displayed.-0 : The spindle ad...

  • Page 129

    NREQ4NREQ7NREQ8NODC3NO. 0391JZRNXWhen machine coordinate of 4th-axis is not fixed at power-up with using absolutepu 1 se coder,1 : no alarm is displayed.0 : alarm 340 is displayed.When machine coordinate of 7th-axis is not fixed at power-up with using absolutepulse coder,1 : no alarm is displayed...

  • Page 130

    NO. 0392#7SRSZ#6#5X4SREPSRPE#3#2#1#O9SRLl1 :0 :1 :0 :SRLl1 : Bit length of a charactor on M-NET is 8 bits.0 : Bit length of a charactor on M-NET is 7 bits.1 :0 :SRPE1 : Parity check of a charactor on M-NET is done.0 : Parity check of a charactor on M-NET is not done.SREP1 : Parity bit of a charac...

  • Page 131

    DGNWEB1 : Changing PMC parameter from MD1 key is allowed regardless of PWE setting.0 : Changing PMC parameter from MD1 key is allowed only in PWE setting = 1.#7# 6#5X4# 3#2#1#Cl,NO. 0394CAKEYWKZRST1 :0 :1 :0 :1 :0 :1 :0 :1 :0 :1 :0 :WKZRST1 : Work coordinate is changed to G54 by reset operation.0...

  • Page 132

    1 :0 :FWBTY P1 : Linear acceleration/deceleration prior to interpolation is type B. (Note-l)0 : Linear acceleration/deceleration prior to interpolation is type A. (Note-2)(Note-l) Acceleration:Started at the start point of the feedrate changing block.Deceleration:Started from the block preceding ...

  • Page 133

    NOPS4 11 : Interference check is not performed for cutter compensation.0 : Interference check is performed for cutter compensation.1 :0 :1 :0 :1 :0 :SERNAI1 : Details of serial interface spindle alarm 409 are displayed on alarmscreen.0 : Details of serial interface spindle alarm 409 are not displ...

  • Page 134

    1 :0 :1 :0 :RPDFF1 : Feed forward control is applied to both cutting feed and rapid traverse.0 : Feed forward control is applied only to cutting feed.SFDEC1: The reference position shift function is enabled. (Note)0: The reference position shift function is disabled.(Note) When SFDEC is set to 1,...

  • Page 135

    FEDNUL 1 : “NULL” code is output as feed data during meaning information.0 : “SPACE” code is output as feed data during meaning information.OUTZRNWhen reference point return is operated during feed-hold status,1 : no alarm appears.0 : alarm 91 appears. (P/S 091)- 133 -

  • Page 136

    NO. 0249I M-code for Minus direction of table indexingIData Type: ByteData Range: 0 to 2550: Motion direction of table indexing is decided by command direction andparameter 079 IXINC.l-255 : M-code for moving minus direction in table indexing is set.When the M-code is commanded together with tabl...

  • Page 137

    NO. 0262Baud rate of M-NETData Type: ByteData Range: 0 to 4Standard value : 3Communication baud rate of M-NET is set.ValueBaud Rate024001480029600319200438400NO. 0265ITime interval of averaging servo current on servo tune screenIData Type: ByteData Range: 0 to 7Time interval of averaging servo cu...

  • Page 138

    NO. 0304M code for small-diameter peck drilling cycleData unit: CharactersData range: 3 to 999Description: This parameter specifies the M code for a small-diameter peck drillingcycle.NO. 0305Spindle speed change ratio for small-diameter peck drilling cycle(with load torque signal)NO. 0306Spindle ...

  • Page 139

    NO. 0310IAxis No. for 1st position switchINO. 03-19Axis No. for 10th posit ion switchData Type: ByteSetting Range: o, 1,239 4,798Axis No. for position switches from 1st to 10th are set in order. Setting value “0”indicates “Not Used”. Setting values 1,2,3,4,7 and 8 indicate X-axis, Y-axis,...

  • Page 140

    NO. 0325Maximum recieving charactor length after communication stop on DNC-2Data Type: ByteSetting Unit: charactorSetting Range : 10 to 255standard value : 255Maximum recieving charactor length after communication stop on DNC2 is set.“0” means the standard value.NO. 0327Number of macro variab...

  • Page 141

    The setting IO-charactor are displayed on CRT at power-up instead of CNC softwareseries/edition.(Note-l) Setting value is same as software operator’s panel general purpose switch.(Note-Z) Available charactor is numerals, alphabets, minus, period and space.(Note-31 When undefined charactors are ...

  • Page 142

    NO. 0351Charactor code-l of titletoNO. 0355ICharactor code-5 of title .IData Type: ByteThe setting 5-charactors are displayed on screen instead of program number.. (Note) Setting value is same as software operator’s panel general purpose switch.NO. 0356Charactor length of 1st line on “DIST TO...

  • Page 143

    .NO. 0378The override value for rigid tapping returnData unit: lOC%lData range: ‘0 to 20Description: This parameter specifies the override value for rigid tapping return.If 0 is set, no override is applied.(Note) This parameter is effective when bit 4 of parameter 0063 (RGDOV) is set to 1.NO. 0...

  • Page 144

    NO. 0402Time constant of rigid tapping during pulling-up motionData Type: WordData Unit: msecData Range: 0 to 4000Time constant of rigid tapping during pulling-up motion is set.When parameter 077#1 (CT3G) is set to “O”, this parameter is common with all gearselection. However, if parameter 07...

  • Page 145

    NO. 0454Absolute counter value of Z-axis at ref,erence pointNO. 0455Absolute counter value of 4th-axis at reference pointNO. 0456IAbsolute counter value of 7th-axis at reference pointINO. 0457IAbsolute counter value of 8th-axis at reference pointIData Type: Word .These parameters are set automati...

  • Page 146

    NO. 0462Time constant of velocity loop on continuous feed without position loopData Type: WordData Unit: 1 msec/lOOOrpmData Range:,O to 32767Time constant of velocity loop on continuous feed without position loop by using PMCaxis control is set. The value is required acceleration time from 0 to 1...

  • Page 147

    NO. 0480Parameter 1 for setting the acceleration for linear acceleration/deceleration prior to interpolationData unitData rangeIncrement systemData unit,,Millimeter machine 1[mm/mini 1 6 to 15000 1 6 to 12000Inch machine0.1 [inch/min]6 to 60006 to 4800Description: This parameter specifies the max...

  • Page 148

    Data unitData rangeData rangeIncrement systemData unitIS-A, IS-BIS-CMillimeter machine 1[mm/m i n]6 to 150006 to 12000Inch machine0.1 [inch/min]6 to 60006 to 4800Description: This parameter specifies the difference between the feedrates of twoblocks, for each axis, for automatic corner decelerati...

  • Page 149

    Data unit: [mseclData range: 1 to 4000Description: This parameter specifies the time (time constant) required to reach thespeed specified with parameter 0485, in look-ahead control mode.(Note-l) Linear acceleration/deceleration prior to interpolat ion is not applied whenparameter 0485 and/or 0486...

  • Page 150

    Data unit-Data rangeData rangeIncrement systemData unitIS-A, IS-BIS-CMetric input1[mm/mi n]0 to 100000 to 12000Inch input0.01[ inch/min]0 to40006 to4800iDescription: These parameters specify the feedrate of retraction to the R position andthat of forward movement from the R position when address ...

  • Page 151

    Data Type: WordData Unit: 1 mm/min (metric output), 0.1 inch/min (inch output)Data Range: 6 to 15000 (metric output), 6 to 6000 (inch output)Measuring feedrate of tool length automatic measurement is set.NO. 0570NO. 0571NO. 0572NO. 0573NO. 0574NO. 0575I Capacity of reference counter for X-axisII ...

  • Page 152

    NO. 0612In-position width for cutting feed for 4th axisData Unit: Detection unitData Range: 0 to 32767Description: These parameters specify the in-position width for cutting feed, for thecutting feed and rapid traverse separate in-position check function.(Note-l) These parameters are effective wh...

  • Page 153

    Data Type: WordData Range: 700 to 1250Standard Value : 1000Gain adjustment value for D/A converter channel-l on Analog Input/Output Interface boardis set.NO. 0674IOffset compensation value for D/A converter channel-lIData Type: WordData Range: 0 to t1023Standard Value : 0Offset compensation value...

  • Page 154

    Data Type: WordData Unit: 1 mm/min (metric output), 0.1 inch/min (inch output)Data Range: 0 to 15000 (metric output), 0 to 6000 (inch output)Declaration end speed of error detect function is set. When command speed becomes lessthan the setting value, the next block starts.NO. 0685IFO speed of PMC...

  • Page 155

    Time constant of acc/dec in rigid tapping for low gear is set. When linear acc/dec(parameter 254 = 1) and parameter 037#6 (VALT)= 1 are selected, this parameterindicates required time from spindle speed 0 to parameter 694. Actual time constant. varys proportionally to the actual spindle speed. Wh...

  • Page 156

    Gear Ratio between Spindle and Position coderData Range1:10 to 74001:20 to 99991:40 to 99991:80 to 9999Maximun spindle speed of rigid tapping for middle gear is set.(Note-l) This parameter is effective only when both parameter 077#1 (CT3G) and 037#6(VALT) are set to Y”.(Note-Z) Maximum spindle ...

  • Page 157

    (Note) When “0” is specified, parameter 121 becomes effective instead of this parameter.T- -NO. 0797Lock for displaying part program No.9000 to 9999Data Type: 2 wordData Range: 0 to 99999999A number is set to prohibit displaying part programs which program number is from 9000to 9999. This par...

  • Page 158

    Data Type: 2 wordData Unit: Output incrementData Range: 0 to 999999997 and E values of tool length automatic measurement are set in order.(Note) In case of input increment l/10, data unit ids changed to l/10.NO. 0832ILimit angle of inserting rotary axis motion for normal direction controlIData ty...

  • Page 159

    NO. 0840IMaximum coordinate value of 1st position switchItoNO. 0849 1 Maximum coordinate value of 10th position switchIData type: 2 wordsData Unit: output incrementData Range: 0 to t99999999The maximum coordinate value of position switch from 1st to 10th is set in order.NO. 0850Minimum coordinate...

  • Page 160

    Data unit: 0. OOlCdeglData range: 0 to 180000Description: This parameter specifies the critical angle between two blocks forautomatic corner deceleration in look-ahead control mode.NO. 0865Critical angle between two blocks for automatic corner decelerationData unit: 0. OOl[degIData range: 0 to 18...

  • Page 161

    Data type: 2 wordsData Unit: input incrementData Range: 0 to 99999999The tolerance of circle radius between start point and end point is set. When thedifference of radius between start point and end point exceeds the specified value,alarm 20 will appear.NO. 0877Time constant for exponent ial acce...

  • Page 162

    Data range: 0 t 0 ?I99999999Description: Thisparameter specifies the first microclearance for return to the Rposition and the second and subsequent clearance of the cutting startpoint, for a small-diameter peck drilling cycle.NO. 0942I Approach speed for origin setting by pressing stopperIData Ty...

  • Page 163

    Data TypeData UnitData Range: 2 words: input increment: 0 to t99999999The distance from stopper to origin point for X,Y,Z and 4th-axis is set respectively.I-NO. 0952Time constant T2 for rapid traverse bell-shaped acceleration/decelerationfor X-axisNO. 0953Time constant T2 for rapid traverse bell-...

  • Page 164

    Data Type: 2 wordsData UnitData Range: detection unit of spindle: 0 to 32767Maximum spindle lag of rigid tapping for low, middle and high gear is set respectively.(Note) These parameter are effective only when parameter 388#6 (CHKERC) is set to “1”.NO. 0960Amount of return a or rigid tapping ...

  • Page 165

    NO. 0994NO.0995NO. 0996NO. 0997NO. 0998NO. 0999Machine position prior to power-off for the first axis~~~I Machine position prior to power-off for the second axisIMachine position prior to power-off for the third axisI Machine position prior to power-off for the fourth axisII Machine position prio...

  • Page 166

    NO. 7724Machine position prior to power-off for the sixth axisData unitIncrement systemIS-BIS-CMetric machine [mm]0.0010.0001Inch machine [inch]0.00010.00001Rotat ion axis [deg]0.0010.0001Data range: 0 to t999999999These parameters display the machine position prior to power-off. They are used fo...

  • Page 167

    INDEX<C‘>Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31<F>Function parameters (For machining series) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1<P>Parameter descr...

  • Page 168

    Parameters related to theParameters related to theParameters related to theParameters related to theParameters related to thePMC . . . . . . . . . . . . . . . ..?...........................26position switch function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23reader/punch int...

  • Page 169

  • Page 170

x