Navigation

  • Page 1

    GE Fanuc AutomationComputer Numerical Control ProductsLaser C1000 / C2000 / C4000―Model Efor CE MarkOperator's ManualGFZ-70314EN/01May 2001

  • Page 2

    GFL-001Warnings, Cautions, and Notesas Used in this PublicationWarningWarning notices are used in this publication to emphasize that hazardous voltages, currents,temperatures, or other conditions that could cause personal injury exist in this equipment or maybe associated with its use.In situatio...

  • Page 3

    B-70314EN/01 PREFACEp-1PREFACEThis manual covers the following models:ModelAbbreviationFANUC LASER C1000-MODEL EC1000-EFANUC LASER C2000-MODEL EC2000...

  • Page 4

    B-70314EN/01 TABLE OF CONTENTSc - 1TABLE OF CONTENTSPREFACEPREFACEPREFACEPREFACE.....................................................................................................

  • Page 5

    TABLE OF CONTENTS B-70314EN/01c - 23.4BASE OF OSCILLATOR........................................................................................................................ 5...

  • Page 6

    B-70314EN/01 TABLE OF CONTENTSc - 35.3.4Exhaust Pump Filter ............................................................................................................. 1005.4AG...

  • Page 7

    B-70314EN/01 1.OVERVIEW- 1 -1 OVERVIEWIn this manual, we have tried as for as possible to address all issues.However, space restrictions prevent us from desc...

  • Page 8

    1.OVERVIEW B-70314EN/01- 2 -1.1 MANUAL CONTENTSThis manual consists of the following chapters and appendixes:1.OVERVIEWChapter 1 covers the configuration of ...

  • Page 9

    B-70314EN/01 1.OVERVIEW- 3 -1.2 APPLICABLE MODELSThis manual covers the following models:ModelAbbreviationFANUC LASER C1000-MODEL EC1000-EFANUC LASER C2000-M...

  • Page 10

    1.OVERVIEW B-70314EN/01- 4 -1.3 RELATED MANUALSThe following manuals are available for the FANUC LASER C1000/C2000/C4000-MODEL E :DESCRIPTIONSB-63192ENCONNEC...

  • Page 11

    B-70314EN/01 1.OVERVIEW- 5 -1.4 FOR SAFE OPERATIONThis manual contains precautions which must be observed duringoperation of the laser oscillator, to ensure ...

  • Page 12

    1.OVERVIEW B-70314EN/01- 6 -1.5 NOTES ON READING THIS MANUALThe functions of a laser machining system depend not only on thelaser oscillator, but also on the...

  • Page 13

    B-70314EN/01 2.SAFETY- 7 -2 SAFETYC1000-E, C2000-E, and C4000-E produce the rated output laserpower of 1000W, 2000W, and 4000W. The CO2 laser beam is ...

  • Page 14

    2.SAFETY B-70314EN/01- 8 -2.1 LASER BEAM1)Potential hazardsLaser oscillator emits CO2 laser beam(10.6 µm), which is highpower and invisible.•Being ...

  • Page 15

    B-70314EN/01 2.SAFETY- 9 -3)Position of laser beam emissionFig.2.1(a) is the position of panel that laser beam exposure isoccurred without panel in C1...

  • Page 16

    2.SAFETY B-70314EN/01- 10 -Fig.2.1(a) Laser beam exposure position without panel as operating (C1000-E)Fig.2.1(b) Laser beam exposure position without...

  • Page 17

    B-70314EN/01 2.SAFETY- 11 -Fig.2.1(d) The position of laser beam delivery (C1000-E)

  • Page 18

    2.SAFETY B-70314EN/01- 12 -Fig.2.1(e) The position of laser beam delivery (C2000-E)Fig.2.1(f) The position of laser beam delivery (C4000-E)

  • Page 19

    B-70314EN/01 2.SAFETY- 13 -2.2 HIGH VOLTAGE1)Potential hazardsThere is RF voltage of 3 to 4kVo-p in the cabinet of the laseroscillator.There is 200 VA...

  • Page 20

    2.SAFETY B-70314EN/01- 14 -Fig.2.2(a) Position of high voltage in C1000-E (Front, maintenance side)Fig.2.2(b) Position of high voltage in C1000-E (Bac...

  • Page 21

    B-70314EN/01 2.SAFETY- 15 -Fig.2.2(c) Position of high voltage in C2000-E (Front, maintenance side)Fig.2.2(d) Position of high voltage in C2000-E (Bac...

  • Page 22

    2.SAFETY B-70314EN/01- 16 -Fig.2.2(e) Position of high voltage in C4000-E (Front, maintenance side)Fig.2.2(f) Position of high voltage in C4000-E (Bac...

  • Page 23

    B-70314EN/01 2.SAFETY- 17 -2.3 SAFETY ENCLOSURE (AT YOUR WORK STATION)1)Potential hazardsCO2 beam is delivery from oscillator. Direct or scattered bea...

  • Page 24

    2.SAFETY B-70314EN/01- 18 -2.4 FIRE1)Potential hazardsWhen you work with the laser oscillator or machine, hotfragments or slag can scatter from your w...

  • Page 25

    B-70314EN/01 2.SAFETY- 19 -2.5 TOXIC FUME1)Potential hazardsSome materials such as certain plastics can emit toxic fumewhen they burn under the laser ...

  • Page 26

    2.SAFETY B-70314EN/01- 20 -2.6 HIGH TEMPERATURE1)Potential hazardsWhen you touch a part of high temperature, your skin burn.2)Safety recommendationsTh...

  • Page 27

    B-70314EN/01 2.SAFETY- 21 -Fig.2.6(a) Position of high temperature in C1000-E (Front, maintenance side).Fig.2.6(b) Position of high temperature in C10...

  • Page 28

    2.SAFETY B-70314EN/01- 22 -Fig.2.6(c) Position of high temperature in C2000-E (Front, maintenance side).Fig.2.6(d) Position of high temperature in C20...

  • Page 29

    B-70314EN/01 2.SAFETY- 23 -Fig.2.6(e) Position of high temperature in C4000-E (Front, maintenance side).Fig.2.6(f) Position of high temperature in C40...

  • Page 30

    2.SAFETY B-70314EN/01- 24 -2.7 WARNING LABELSFig.2.7(a)-(f) show the location of the warning labels indicating thehigh voltage and laser beam path.Fig...

  • Page 31

    B-70314EN/01 2.SAFETY- 25 -Fig.2.7(a) Location of the warning sticker (C1000-E:Front side).Fig.2.7(b) Location of the warning sticker (C1000-E:Back si...

  • Page 32

    2.SAFETY B-70314EN/01- 26 -Fig.2.7(c) Location of the warning sticker (C2000-E:Front side).Fig.2.7(d) Location of the warning sticker (C2000-E:Back si...

  • Page 33

    B-70314EN/01 2.SAFETY- 27 -Fig.2.7(e) Location of the warning sticker (C4000-E:Front side).Fig.2.7(f) Location of the warning sticker (C4000-E:Back si...

  • Page 34

    2.SAFETY B-70314EN/01- 28 -Detail of warning sticker(1) Warning logotype (C1000-E)(1) Warning logotype (C2000-E, C4000-E)

  • Page 35

    B-70314EN/01 2.SAFETY- 29 -(2) Warning logotype(3) Label for defeasible non-interlocked protective housing(4) Label for defeasible non-interlocked pro...

  • Page 36

    2.SAFETY B-70314EN/01- 30 -(6) Aperture label(7) Label of non-interlocked protective panel(8) Identification label

  • Page 37

    B-70314EN/01 2.SAFETY- 31 -(9) Address label(10) High voltage warning label(11) Supply voltage label(12) Label of over-current protective

  • Page 38

    2.SAFETY B-70314EN/01- 32 -(13) Label of motor and transformer (C1000-E)(13) Label of motor and transformer (C2000-E)(13) Label of motor and transform...

  • Page 39

    B-70314EN/01 2.SAFETY- 33 -(14) Label of warning light(15) Maintenance label(16) Certification label(17) Short-circuit interrupting capacity of main b...

  • Page 40

    2.SAFETY B-70314EN/01- 34 -(18) Label for regurating the atmospheric gases in the oscillatorhousing(19) Label for cooling water and laser gas

  • Page 41

    B-70314EN/01 2.SAFETY- 35 -2.8 HIGH-PRESSURE GASDo not allow any dangerous or high-pressure gas to get into theoscillator housing. The oscillator cabi...

  • Page 42

    2.SAFETY B-70314EN/01- 36 -2.9 KEY CONTROLAll the laser products have to comply with the various kinds of lasersafety regulations, which include the u...

  • Page 43

    B-70314EN/01 2.SAFETY- 37 -2.10 SHUTTER LOCKThe shutter lock is prepared because it dose not put out the laser beamby mistake. If you do not put out t...

  • Page 44

    2.SAFETY B-70314EN/01- 38 -2.11 EMERGENCY STOP BUTTONPress the emergency stop button when it is dangerous and breaksdown. The oscillator is stopped di...

  • Page 45

    B-70314EN/01 2.SAFETY- 39 -2.12 WARNING LIGHT (OPTIONAL)Laser oscillator is equipped with the warning light optionally. Thelight is flashed during dis...

  • Page 46

    2.SAFETY B-70314EN/01- 40 -2.13 INAPPOSITE USE OF LASER OSCILLATORInapposite use and the result are described in each explanation place.Inapposite maj...

  • Page 47

    B-70314EN/01 3.INSTALLATION- 41 -3 INSTALLATION

  • Page 48

    3.INSTALLATION B-70314EN/01- 42 -3.1 CONDITION3.1.1 Environmental Conditions(1) Ambient+5 to 30°C(2) Temperature driftMax 1.1°C/min(3) Humidity< 75% (relative)(4...

  • Page 49

    B-70314EN/01 3.INSTALLATION- 43 -3.1.4 Cooling Water(1) Cooling water specificationThe quality of cooling water is specified in the table below. Iftap water is used,...

  • Page 50

    3.INSTALLATION B-70314EN/01- 44 - CAUTIONIn winter or in a cold district, when the oscillator is ata rest and the ambient temperature gets to or belowthe freezing poi...

  • Page 51

    B-70314EN/01 3.INSTALLATION- 45 -3.2 TRANSPORTATION3.2.1 Lifting Laser OscillatorIn lifting the laser oscillator, be sure to use the four eyebolts screwedinto the top...

  • Page 52

    3.INSTALLATION B-70314EN/01- 46 -3.2.2 Packing1)ClampWhen shipped from FANUC, the two components of the laserlisted below are in the clamped position. Because this is...

  • Page 53

    B-70314EN/01 3.INSTALLATION- 47 -Fig.3.2.2(a) Clamp layout (C1000-E)

  • Page 54

    3.INSTALLATION B-70314EN/01- 48 -Fig.3.2.2(b) Clamp layout (C2000-E)

  • Page 55

    B-70314EN/01 3.INSTALLATION- 49 -Fig.3.2.2(c) Clamp layout (C4000-E)

  • Page 56

    3.INSTALLATION B-70314EN/01- 50 -2)WaterBe sure to drain water in the oscillator at shipment.Refer to the maintenance manual for draining. CAUTIONIf water remains in ...

  • Page 57

    B-70314EN/01 3.INSTALLATION- 51 -3.3 STORAGEThe various kinds of clamps should be used only during thetransportation. Especially the clamps used for resonator should ...

  • Page 58

    3.INSTALLATION B-70314EN/01- 52 -3.4 Base of oscillatorIn laser oscillator, the two type of that is the four taps and hole areprepared in the base as shown in the fig...

  • Page 59

    B-70314EN/01 3.INSTALLATION- 53 -Fig.3.4(c) Cabinet base (C1000-E)Fig.3.4(d) Cabinet base (C2000-E, C4000-E)

  • Page 60

    3.INSTALLATION B-70314EN/01- 54 -3.5 MAINTENANCE AREAThe maintenance areas of laser oscillator series are shown in thefigures below.The customer is requested to prepa...

  • Page 61

    B-70314EN/01 3.INSTALLATION- 55 -Fig.3.5(b) Maintenace area (C2000-E : Short type)Fig.3.5(c) Maintenace area (C2000-E : Long type)

  • Page 62

    3.INSTALLATION B-70314EN/01- 56 -Fig.3.5(d) Maintenace area (C4000-E : Short type)Fig.3.5(e) Maintenace area (C4000-E : Long type)

  • Page 63

    B-70314EN/01 3.INSTALLATION- 57 -3.6 WATER CONNECTION3.6.1 ChillerMake the cooling water re-circulate in the closed loop using a chillerunit.The cooling requirements ...

  • Page 64

    3.INSTALLATION B-70314EN/01- 58 -3.6.2 Cooling Water TemperatureThroughout the year, set the chiller water temperature to 27°C ingeneral regions and 30°C in humid r...

  • Page 65

    B-70314EN/01 3.INSTALLATION- 59 -3.7 LASER GAS3.7.1 Gas BottleUse the gas bottle of the volume of 7m3. Store the necessary numberof bottles according to the operation...

  • Page 66

    3.INSTALLATION B-70314EN/01- 60 -•Always keep the piping materials clean. Do not allow foreignmatter to get in the pipe.•Use a pressure reducer that is free from ...

  • Page 67

    B-70314EN/01 3.INSTALLATION- 61 -3.8 LASER BEAMHere explanation are given for the convenience of designingmachines.3.8.1 Position and Tolerance of Laser Beam ExitThe ...

  • Page 68

    3.INSTALLATION B-70314EN/01- 62 -Table 3.8.1 Position of laser beam exitModelW1W2W3HC4000-ELong path length type420±565485921±53.8.2 Beam DivergenceThe beam diverge...

  • Page 69

    B-70314EN/01 3.INSTALLATION- 63 -3.9 ELECTRIC CONNECTIONThe following cables should be connected to the laser. Refer to theConnecting Manual of the controller (CNC).C...

  • Page 70

    3.INSTALLATION B-70314EN/01- 64 -Fig.3.9(c) Cable connection (C4000-E)

  • Page 71

    B-70314EN/01 3.INSTALLATION- 65 -3.9.1 Power Cable (L1, L2, L3)Use the cable with 4 cores.Conductor cross section must be more than 22mm2 (C1000-E), 35mm2(C2000-E, C4...

  • Page 72

    3.INSTALLATION B-70314EN/01- 66 -3.9.4 Other Signal Cables to the IF PCB1)Emergency stop signal input (ESP1, ESP2)This terminal is shorted usually.2)OFF prohibition s...

  • Page 73

    B-70314EN/01 3.INSTALLATION- 67 -3.9.5 Safety InterlockThe diagram of safety interlock circuit is shown in Figs.(a) to (c).Fig.3.9.5(a) Safety interlock circuit (C100...

  • Page 74

    3.INSTALLATION B-70314EN/01- 68 -Fig.3.9.5(b) Safety interlock circuit (C2000-E)

  • Page 75

    B-70314EN/01 3.INSTALLATION- 69 -Fig.3.9.5(c) Safety interlock circuit (C4000-E)

  • Page 76

    3.INSTALLATION B-70314EN/01- 70 -Meaning of signals1) PF1, PF2 :These are the voltage release terminals of a mainbreaker (QF1). Impress the voltage of 24VDC.PF1 :+24V...

  • Page 77

    B-70314EN/01 3.INSTALLATION- 71 -3.9.6 EMC CountermeasureCable shieldInstall the appended Cable Shield (A04B-0811-D021) in power cable.Fig.3.9.6 Cable shieldMain powe...

  • Page 78

    4.FUNCTIONS B-70314EN/01- 72 -4 FUNCTIONSThis chapter describes the internal structure, components, andoperating sequence of the laser oscillator.Contents of t...

  • Page 79

    B-70314EN/01 4.FUNCTIONS- 73 -4.1 INTERNAL STRUCTUREFigs.4.1(a) to (c) show the internal structure of the laser oscillator.Fig.4.1(a) Block diagram (C1000-E)

  • Page 80

    4.FUNCTIONS B-70314EN/01- 74 -Fig.4.1(b) Block diagram (C2000-E)

  • Page 81

    B-70314EN/01 4.FUNCTIONS- 75 -Fig.4.1(c) Block diagram (C4000-E)

  • Page 82

    4.FUNCTIONS B-70314EN/01- 76 -4.1.1 OutlineThe FANUC C1000/C2000/C4000-MODEL E consists of a laserresonator, laser excitation power supply, forced gas circulat...

  • Page 83

    B-70314EN/01 4.FUNCTIONS- 77 -Protective housingAn enclosure that houses the above components. The housing,consisting of metal panels and doors, completely enc...

  • Page 84

    4.FUNCTIONS B-70314EN/01- 78 -4.2 COMPONENT DETAILSThe following describes the details of each component of the laseroscillator. Figs.4.2(a) to (f) show the in...

  • Page 85

    B-70314EN/01 4.FUNCTIONS- 79 -Fig.4.2(c) Internal structure of C2000-E (Front, maintenance side)Fig.4.2(d) Internal structure of C2000-E (Back side)

  • Page 86

    4.FUNCTIONS B-70314EN/01- 80 -Fig.4.2(e) Internal structure of C4000-E (Front, maintenance side)Fig.4.2(f) Internal structure of C4000-E (Back side)

  • Page 87

    B-70314EN/01 4.FUNCTIONS- 81 -(1) ResonatorThe resonator consists of an output coupler, rear mirror, foldingmirrors, discharge tubes, power sensor unit, etc. I...

  • Page 88

    4.FUNCTIONS B-70314EN/01- 82 -(10) Heat exchanger (outlet)Heat exchanger used to cool the laser gas that has been heated bycompression in the turbo blower, bef...

  • Page 89

    B-70314EN/01 4.FUNCTIONS- 83 -(17) Beam absorberWhile the laser oscillator is operating with the shutter closed, thelaser beam is guided into the beam absorber...

  • Page 90

    4.FUNCTIONS B-70314EN/01- 84 -(24) Interface PCBI/O LINK (serial interface). Because this is a serial interface,optical fiber cable can be used to enable long-...

  • Page 91

    B-70314EN/01 4.FUNCTIONS- 85 -4.3 OPERATION SEQUENCELaser oscillator is controlled by CNC. When you turn on the start key(run key), start sequence and calibrat...

  • Page 92

    4.FUNCTIONS B-70314EN/01- 86 -[SEQ0] POWER OFF stateThis is the state prior to power on where all the signals arein off state.[SEQ10] INITIAL stateAfter power ...

  • Page 93

    B-70314EN/01 4.FUNCTIONS- 87 -RUN OFF SequenceNo.Status of laser sequence30LSTR23Switch over to gas pressure of LRDY from gas pressure ofLSTR20LRDY1475 sec wai...

  • Page 94

    4.FUNCTIONS B-70314EN/01- 88 -4.4 LASER PROCESSING MACHINE SYSTEMThe material processing machine using FANUC LASERC1000/C2000/C4000-MODEL E is usually composed...

  • Page 95

    B-70314EN/01 4.FUNCTIONS- 89 -(4) Guide laser (Laser diode)A diode laser is used for coarse-control of the optical systemaxis after a light beam is output from...

  • Page 96

    5.MAINTENANCE B-70314EN/01- 90 -5 MAINTENANCEIn FANUC LASER C1000/C2000/C4000-MODEL E, periodicinspection items have been reduced, and adjustments have been madeeasy....

  • Page 97

    B-70314EN/01 5.MAINTENANCE- 91 -5.1 DAILY INSPECTIONTable 5.1 lists daily inspection items. Inspect the FANUC LASERC1000/C2000/C4000-MODEL E according to this table. ...

  • Page 98

    5.MAINTENANCE B-70314EN/01- 92 -5.2 PERIODIC MAINTENANCETable 5.2 shows the periodic maintenance items and the periods. Theoperation hour can be known from the indica...

  • Page 99

    B-70314EN/01 5.MAINTENANCE- 93 -5.3 DETAILS OF MAINTENANCEWhen opening the panels during maintenance, keep the power turnoff.5.3.1 Maintenance Panels and Oil Gauge Po...

  • Page 100

    5.MAINTENANCE B-70314EN/01- 94 -Fig.5.3.1(c) Maintenance panel (C4000-E)

  • Page 101

    B-70314EN/01 5.MAINTENANCE- 95 -The locations of the oil gages are shown in Figs.5.3.1(d) to (f). Theseoil gages can be checked through a window without having to ope...

  • Page 102

    5.MAINTENANCE B-70314EN/01- 96 -Fig.5.3.1(f) Oil gauge of turbo blower and exhaust pump (C4000-E)

  • Page 103

    B-70314EN/01 5.MAINTENANCE- 97 -5.3.2 Turbo Blower OilCheck methodCheck the amount of oil in the turbo blower while referring to thefigure below. The oil level should...

  • Page 104

    5.MAINTENANCE B-70314EN/01- 98 -3.Clean the oil inlet, hexagonal-head screw, and O-ring by wipingwith clean cloth or paper. Make sure that these parts are free ofdust...

  • Page 105

    B-70314EN/01 5.MAINTENANCE- 99 -5.3.3 Exhaust Pump OilFig. 5.3.3 shows the location of the oil gauge. See also Fig. 5.3.4.Check methodWatch the oil gauge, and check t...

  • Page 106

    5.MAINTENANCE B-70314EN/01- 100 -5.3.4 Exhaust Pump FilterReplacement methodReplace the filter every 3000 hours of operation or every year of use,whichever is earlier...

  • Page 107

    B-70314EN/01 5.MAINTENANCE- 101 -5.4 AGINGIf the machine has not been unused for an extended period of time(three days or longer) or if the laser gas circulatory syst...

  • Page 108

    5.MAINTENANCE B-70314EN/01- 102 -5.4.2 Aging MethodThe oscillator control software provides an automatic aging function.If aging is required after consecutive holiday...

  • Page 109

    B-70314EN/01 5.MAINTENANCE- 103 -(4) Perform internal discharge with the following settings. Internaldischarge can be performed either automatically using theappropri...

  • Page 110

    5.MAINTENANCE B-70314EN/01- 104 -5.5 MAINTENANCE PARTSTo procure consumables, contact the machine builder or FANUCservice center, and tell the applicable specificatio...

  • Page 111

    B-70314EN/01 5.MAINTENANCE- 105 -5.5.2 Maintenance ToolsFollowing tools are recommended for maintenance.EquipmentEquipmentConditionApplicationAC voltmeterAccuracy: ±...

  • Page 112

    6.TROUBLESHOOTING B-70314EN/01- 106 -6 TROUBLESHOOTINGThe FANUC C series laser is provided with various sensors. They arealways monitored by a CNC. If the oscillator becomes abnor...

  • Page 113

    B-70314EN/01 6.TROUBLESHOOTING- 107 -6.1 CHECKING ON FAULTSAfter identifying the following items, call the FANUC service center.In some cases, a symptom is not actually a fault in...

  • Page 114

    6.TROUBLESHOOTING B-70314EN/01- 108 -6.2 RESPONDING TO ALARM MESSAGES ON THE SCREENSee a list of alarms in an appendix at the end of this manual.Alarm No. 4061Anomaly of AD conver...

  • Page 115

    B-70314EN/01 6.TROUBLESHOOTING- 109 -2. Confirming operation and investigating the cause of a faultConfirm the symptom, and call the FANUC service center.No.Cause of troubleSoluti...

  • Page 116

    6.TROUBLESHOOTING B-70314EN/01- 110 -3. SolutionNo.Cause of troubleSolution1External laser gas pipeabnormalImprove the external pipe. The pipeshould be installed in such a way tha...

  • Page 117

    B-70314EN/01 6.TROUBLESHOOTING- 111 -No.Cause of troubleSolution3Loose fixing parts ofelectrode4Gas circulating systemleakage of gas or water5The gas flow control valueis closedIt...

  • Page 118

    6.TROUBLESHOOTING B-70314EN/01- 112 -Alarm No. 4069Anomaly of power supply unit voltage of IF PCB(Refer to DGN = 960/bit 0)This alarm appears when there occurs the anomaly in the ...

  • Page 119

    B-70314EN/01 6.TROUBLESHOOTING- 113 -Alarm No. 4073Decrease of laser gas pressure (Refer to DGN = 960/bit 5)The pressure of the laser gas supplied to the laser oscillator ismonito...

  • Page 120

    6.TROUBLESHOOTING B-70314EN/01- 114 -Alarm No. 4076Laser output decrease (Refer to DGN = 906)This alarm is issued, if the monitored laser output is much lower thanthe specified la...

  • Page 121

    B-70314EN/01 6.TROUBLESHOOTING- 115 -No.Cause of troubleSolution3Gas leakage from theinternal piping4Anomaly of pressuresensor5The gas flow control valveis not normal.6Anomaly of ...

  • Page 122

    6.TROUBLESHOOTING B-70314EN/01- 116 -Alarm No. 4081Anomaly of gas pressure control (Refer to DGN = 905)Pressing the RUN (pressure control start) button starts expelling airfrom th...

  • Page 123

    B-70314EN/01 6.TROUBLESHOOTING- 117 -Alarm No. 4083Shutter failure to openThis alarm occurs when the shutter does not reach the correct positionat a certain time (pre-flow time of...

  • Page 124

    6.TROUBLESHOOTING B-70314EN/01- 118 -Alarm No. 4088Discharge tube voltage drop (Refer to DGN 909.)This alarm is issued, if the voltage applied to the discharge tube dropslargely. ...

  • Page 125

    B-70314EN/01 6.TROUBLESHOOTING- 119 -Alarm No. 4100Turbo blower invertor abnormal (Refer to bit 0 of DGN 962.)This alarm is issued, if an invertor used to run the blower becomesab...

  • Page 126

    6.TROUBLESHOOTING B-70314EN/01- 120 -Alarm No. 4107External reflecting mirror not installedThis alarm is issued, if the beam reflecting unit is not attached with amirror or mirror...

  • Page 127

    APPENDIX

  • Page 128

    B-70314EN/01 APPENDIX A.EXTERNAL VIEW OF LASER OSCILLATOR- 123 -A EXTERNAL VIEW OF LASEROSCILLATORFig.A(a) External view of laser oscillator (C1000-E)

  • Page 129

    A.EXTERNAL VIEW OF LASER OSCILLATOR APPENDIX B-70314EN/01- 124 -Fig.A(b) External view of laser oscillator (C2000-E : short optical path length type)Fig.A(c) External view of laser oscillator (C2000-E : long optical path length type)

  • Page 130

    B-70314EN/01 APPENDIX A.EXTERNAL VIEW OF LASER OSCILLATOR- 125 -Fig.A(d) External view of laser oscillator (C4000-E : short optical path length type)Fig.A(e) External view of laser oscillator (C4000-E : long optical path length type)

  • Page 131

    B.SPECIFICATIONS APPENDIX B-70314EN/01- 126 -B SPECIFICATIONSItemContentsModelC1000-EC2000-EC4000-EPrincipleRF discharge excited fast axial gas flow CO2 laserStructureOscillator and Vacuumpum...

  • Page 132

    B-70314EN/01 APPENDIX C.ERROR CODE LIST- 127 -C ERROR CODE LISTNumberContentsAlarm level4061Anomaly in AD converter 1ALARM 14062Anomaly in AD converter 2ALARM 14063Anomaly in laser power supply ...

  • Page 133

    D.FANUC SERVICE NETWORK APPENDIX B-70314EN/01- 128 -D FANUC SERVICE NETWORKFANUC LTDHeadquarters and Service division :Oshino-mura, Yamanashi Prefecture, 401-0597, JapanPhone 555-84-5555Fax 555-84-5512Country code 8...

  • Page 134

    B-70314EN/01 APPENDIX E.GLOSSARY- 129 -E GLOSSARYNameMeaningAccess panelThat protective component of a housing or enclosure which, when removed orshifted, can cause exposure to ...

  • Page 135

    E.GLOSSARY APPENDIX B-70314EN/01- 130 -NameMeaningOperationLaser product's action covering all intended functions, not including maintenanceor service.Optical resonatorDevice in...

  • Page 136

    B-70314EN/01 INDEXi - 1INDEXAAAAAGING............................................................. 101Aging Method..............................

  • Page 137

    INDEX B-70314EN/01i - 2FOR SAFE OPERATION................................... 5FUNCTIONS .................................................... ...

  • Page 138

    B-70314EN/01 INDEXi - 3WARNING LIGHT (OPTIONAL) .................... 39WATER CONNECTION................................... 57

  • Page 139

    Revision RecordFANUC LASER C1000/C2000/C4000-MODEL E For Europe OPERATOR’S MANUAL (B-70314EN)01May, 2001EditionDateContentsEditionDateContents

  • Page 140

x