Navigation

  • Page 1

    Haas Technical Publications ES0246 Rev AXAug 2015Lifting InstructionsMILLS, LATHES, UMC, AND ROTARIESOverviewThis document provides lifting instructions for Haas machines.ContentsImportant Information ....................................................2VF-1/2/VM-2 ..................................

  • Page 2

    ES0246 Rev AXAug 2015Page 2 of 29Haas Technical PublicationsLifting InstructionsImportant InformationPlease read these instructions in their entirety before attempting to lift the machine.WARNINGIT IS IMPERATIVE THAT PREPARATION AND LIFTING OF THE MACHINE BE PERFORMED BY PROFESSIONAL RIGGERS. THE...

  • Page 3

    ES0246 Rev AXAug 2015Page 3 of 29Haas Technical PublicationsLifting InstructionsVertical Machining CentersVF-1 / VF-2 Series / VM-2 Lift PlacardRefer to the lifting placard for small VMCs. Attach the lifting bracket and chains as shown. Ensure that the chains do not contact the sheet metal enclos...

  • Page 4

    ES0246 Rev AXAug 2015Page 4 of 29Haas Technical PublicationsLifting InstructionsVF-3 / VF-4 Lift PlacardRefer to the lifting placard for the VF-3 and VF-4. Attach chains to the lifting points as shown. Ensure that the chains do not contact the sheet metal enclosure or electrical cables. Note the ...

  • Page 5

    ES0246 Rev AXAug 2015Page 5 of 29Haas Technical PublicationsLifting InstructionsVF-3YT / VF-5 Series / VM-3 Lift PlacardRefer to the lifting placard for the VF-3YTs, VF-5s, and VM-3. Attach chains to the lifting points as shown. Ensure that the chains do not contact the sheet metal enclosure or ...

  • Page 6

    ES0246 Rev AXAug 2015Page 6 of 29Haas Technical PublicationsLifting InstructionsLarge VMC Lift PlacardRefer to the lifting placard for large VMCs. Attach chains to the lifting points as shown. Ensure that the chains do not contact the sheet metal enclosure or electrical cables. Note the use of sp...

  • Page 7

    ES0246 Rev AXAug 2015Page 7 of 29Haas Technical PublicationsLifting InstructionsVF-6 to 12 / VM-6 Lifting Hardware Details1. The lifting bracket can be found beneath the step enclosure. Remove the two steps located on the sides of the Y-axis way cover. 1. Removescrews2. Slide stepout2. The brack...

  • Page 8

    ES0246 Rev AXAug 2015Page 8 of 29Haas Technical PublicationsLifting InstructionsMini Mill Lift PlacardHaas Automation does not provide a lifting kit for the Mini Mill. The lifting features are built into the machine. It is the machine rigger’s responsibility to provide the means to lift and po...

  • Page 9

    ES0246 Rev AXAug 2015Page 9 of 29Haas Technical PublicationsLifting InstructionsToolroom Mills Lift PlacardHaas Automation does not provide a lifting kit for the Toolroom Mill. The lifting features are built into the machine. It is the machine rigger’s responsibility to provide the means to lif...

  • Page 10

    ES0246 Rev AXAug 2015Page 10 of 29Haas Technical PublicationsLifting InstructionsToolroom Mills Lift PlacardHaas Automation does not provide a lifting kit for the Toolroom Mill. The lifting features are built into the machine. It is the machine rigger’s responsibility to provide the means to li...

  • Page 11

    ES0246 Rev AXAug 2015Page 11 of 29Haas Technical PublicationsLifting InstructionsDT/DM-1 Lift PlacardRefer to the lifting placard for the DT-1 and DM-1. Attach lifting chains and hooks to the lifting points as shown. Ensure that the chains do not contact the sheet metal enclosure or electrical ca...

  • Page 12

    ES0246 Rev AXAug 2015Page 12 of 29Haas Technical PublicationsLifting InstructionsDT-1 Lifting Hardware Details1. Loosen, but do not remove, the top row of screws for the Y-axis way cover. 2. Remove the two lower screws.RemoveLoosen3. Remove the two bolts on the front sides of the Y-axis way cove...

  • Page 13

    ES0246 Rev AXAug 2015Page 13 of 29Haas Technical PublicationsLifting Instructions4. Lift up the Y-axis way cover over the linear guides and push the cover toward the table.5. Install the eyebolts and necessary shackles. 6. Remove the 3 roof panels shown for lifting strap attachment access. Attac...

  • Page 14

    ES0246 Rev AXAug 2015Page 14 of 29Haas Technical PublicationsLifting InstructionsHorizontal Machining CentersEC-400 / 500 Lift PlacardRefer to the lifting placard for EC-400/500. Attach chains to the lifting points as shown. Ensure that the chains do not contact the sheet metal enclosure or elect...

  • Page 15

    ES0246 Rev AXAug 2015Page 15 of 29Haas Technical PublicationsLifting InstructionsEC-400 / 500 Lifting Hardware Details1. Remove the top front panels of the machine.2. Before lifting the machine, remove the hole plugs and install four 1"-8 forged steel shoulder eyebolts, 1" steel washers...

  • Page 16

    ES0246 Rev AXAug 2015Page 16 of 29Haas Technical PublicationsLifting InstructionsEC-400 Pallet Pool Lift PlacardRefer to the lifting placard for the EC-400 pallet pool. Attach chains to the lifting points as shown. Ensure that the chains do not contact the sheet metal enclosure or electrical cabl...

  • Page 17

    ES0246 Rev AXAug 2015Page 17 of 29Haas Technical PublicationsLifting InstructionsEC-400 Pallet Pool Lifting Hardware Details1. Before lifting the machine, install four (4) 5/8" x 1-1/16" eyebolts and four (4) 5/8" lat washers. Note: The two left eyebolts are installed into blocks b...

  • Page 18

    ES0246 Rev AXAug 2015Page 18 of 29Haas Technical PublicationsLifting InstructionsEC-1600 Lift PlacardRefer to the lifting placard for EC-1600. Attach chains to the lifting points as shown. Ensure that the chains do not contact the sheet metal enclosure or electrical cables. The lifting kit for th...

  • Page 19

    ES0246 Rev AXAug 2015Page 19 of 29Haas Technical PublicationsLifting InstructionsEC-1600 Lifting Hardware Details1. Wheels can be used to help position the lifting beams beneath the EC-1600. The lifting kit (LK1600) is available from Haas Automation. 2. Position the lifting beams under the machi...

  • Page 20

    ES0246 Rev AXAug 2015Page 20 of 29Haas Technical PublicationsLifting InstructionsTurning CentersST-10 Series Lift PlacardRefer to the lifting placard for the ST-10 series lathes. Lifting hardware is not provided by Haas Automation. Attach chains and shackles as shown. Ensure that the chains do no...

  • Page 21

    ES0246 Rev AXAug 2015Page 21 of 29Haas Technical PublicationsLifting InstructionsST-10 Series Lifting Hardware Details1. Remove the top air duct panel and top right rear panel to access the lifting points.

  • Page 22

    ES0246 Rev AXAug 2015Page 22 of 29Haas Technical PublicationsLifting InstructionsST-20 / ST-25 / ST-30 / ST-35 / DS-30 Series Lift PlacardRefer to the lifting placard for the ST-20, ST-25, ST-30 and DS-30 series lathes. Attach chains to the lifting points as shown. Ensure that the chains do not c...

  • Page 23

    ES0246 Rev AXAug 2015Page 23 of 29Haas Technical PublicationsLifting InstructionsST-20 / ST-25 / ST-30 / ST35 / DS-30 Lifting Hardware Details1. To install the lift kit, remove the left side and two back panels.2. Loop the front lifting strap around the rib of the base casting as shown. Do not l...

  • Page 24

    ES0246 Rev AXAug 2015Page 24 of 29Haas Technical PublicationsLifting InstructionsST-40 / ST-45 Series Lift PlacardRefer to the lifting placard for the ST-40/40L and ST-45/45L lathes. Attach chains to the lifting points as shown. The lifting points are cast into the machine, not in a lift kit. Ens...

  • Page 25

    ES0246 Rev AXAug 2015Page 25 of 29Haas Technical PublicationsLifting InstructionsST-40 / ST-45 Lifting Hardware Details1. To access the lifting points, remove the top access panels.

  • Page 26

    ES0246 Rev AXAug 2015Page 26 of 29Haas Technical PublicationsLifting InstructionsUMC-750 Lift PlacardRefer to the lifting placard for the UMC-750. Attach chains to the lifting points as shown. Ensure that the chains do not contact the sheet metal enclosure or electrical cables.29-0929 Rev B© 201...

  • Page 27

    ES0246 Rev AXAug 2015Page 27 of 29Haas Technical PublicationsLifting InstructionsUMC-750 Lifting Hardware Details1. Remove the front lifting bracket before operating the machine.

  • Page 28

    ES0246 Rev AXAug 2015Page 28 of 29Haas Technical PublicationsLifting InstructionsRotariesLift the rotary table with the lift rings as shown to prevent damage to the gear set. Attach air supply to unit prior to lifting. All rotary tables (HRT's, TR's, TRT's and T5C's) use the 1/2-13 eyebolts for l...

  • Page 29

    ES0246 Rev AXAug 2015Page 29 of 29Haas Technical PublicationsLifting InstructionsMachines without Lifting FeaturesThe following machines do not have a lifting features. Contact a qualiied rigger to move the machine.OM-1AOM-2AOL-1TL-1TL-2TL-3TL-3BGR-512GR-710VS-3HS-3RBAR1006STBAR1508STBAR2008STBA...

x