Navigation

  • Page 1

    NCT®Turning ControlsCollection of Part Program Examples

  • Page 2

    Produced and developed by NCT Ipari Elektronikai kft.H1148 Budapest Fogarasi út 7 : P. O. Box: H1631 Bp. pf.: 26F Phone: (+36 1) 467 63 00 F Fax:(+36 1) 363 6605E-mail: nct@nct.huHome page: www.nct.hu

  • Page 3

    3 © Copyright NCT 06.07.19The Publisher reserves all rights for thecontents of this Manual. No reprinting, evenin extracts, is permissible unless our writtenconsent is obtained. The text of this Manualhas been compiled and checked with utmostcare, yet we assume no liability for p...

  • Page 4

    4Table of Contents1 Contour Definition by Programming Angle ..................................... 52 Contour Definition by Rounding ............................................. 63 Contour Definition by Angles and Rounding .................................... 74 Contour Definition by Chipping ......

  • Page 5

    Collection of Part Program Examples5O20O60O68O80243648Z?7560°OX?O4230°Diagram 11 Contour Definition by Programming Angle%O7001(EXAMPLE 01)N100 G0 X200 Z200N110 T101N120 G0 X82 Z6N130 G92 S3500N140 G96 S150 F0.5 M3 M8N150 G79 X-1 Z5N160 Z3N170 Z1N180 Z0N190 G0 X82 Z2N200 G71 U1 R0.5N210 G71 P230...

  • Page 6

    Collection of Part Program Examples6O20OX?O48O8012245260R6R8R440°Diagram 22 Contour Definition by Rounding%O7002(EXAMPLE 02)N100 G0 X200 Z200N110 T101N120 G0 X82 Z6N130 G92 S3500N140 G96 S150 F0.5 M3 M8N150 G79 X-1 Z5N160 Z3N170 Z1N180 Z0N190 G0 X82 Z2N200 G71 U1 R0.5N210 G71 P230 Q310 U0.3 W0.3...

  • Page 7

    Collection of Part Program Examples7OX?O10O802548Z?7535°60°R10R20R15Diagram 33 Contour Definition by Angles and Rounding%O7003(EXAMPLE 03)N100 G0 X200 Z200N110 T101N120 G0 X82 Z6N130 G92 S3500N140 G96 S150 F0.5 M3 M8N150 G79 X-1 Z5N160 Z3N170 Z1N180 Z0N190 G0 X82 Z2N200 G71 U1 R0.5N210 G71 P230...

  • Page 8

    Collection of Part Program Examples84X45°O60O40O10O8088Z?36785X45°75°Diagram 44 Contour Definition by Chipping%O7004(EXAMPLE 04)N100 G0 X200 Z200N110 T101N120 G0 X82 Z6N130 G92 S3500N140 G96 S150 F0.5 M3 M8N150 G79 X-1 Z5N160 Z3N170 Z1N180 Z0N190 G0 X82 Z2N200 G71 U1 R0.5N210 G71 P230 Q310 U0....

  • Page 9

    Collection of Part Program Examples95. ábra5 Contour Turning - Thread Turning - RecessingThis program involves an entire part program. Spindle setting and head surface roughing isexecuted from line N120 to N190 by means of roughing cycle G79. In this cycle aquadrangular cutting path takes form b...

  • Page 10

    Collection of Part Program Examples10N410 to N680. This part shows, that the recessing cutter works with two separatecompensations so that the difference between the two compensations is exactly the cutterwidth. The recessing cutter is best to be a little - the double of smoothing allowance - thi...

  • Page 11

    Collection of Part Program Examples11%O7008(EXAMPLE 08)N100 G0 X200 Z200N110 T101N120 G0 X62 Z10N130 G92 S3500N140 G96 S150 M8 M3N150 G79 X-1 Z5 F0.2N160 Z3N170 Z1N180 Z0N190 G0 X62 Z2/1 N200 G71 U1 R0.5/1 N210 G71 U0.3 W0.3 F0.5 P250Q370N220 G0 X200 Z200N230 T202N240 G0 X16 Z10N250 G42 X8 Z2N260...

  • Page 12

    Collection of Part Program Examples12O90R3.5R1R1R7.5O410°R2.58°30'O90.32O953526.511.6Diagram 66 Contour Definition - with Head Roughing Cycle and Intersection PointCalculation%O7009(EXAMPLE 09)N100 G0 X200 Z200N110 T101N120 G0 X98 Z6N130 G92 S3500N140 G96 S150 F0.5 M3 M8/1 N150 G72 W1 R0.5/1 N1...

  • Page 13

    Collection of Part Program Examples13O20O40O60O80O1002040508090150160Diagram 77 Contour Turning with Roughing Cycle%O7012(EXAMPLE 12)N100 T101N110 G0 X40 Z10N115 G92 S2500N120 G96 S150 M3 M8 F0.3N130 G0 X100 Z1N140 G71 U1 R0.5N150 G71 U0.3 W0.3 F0.5 P170 Q270N160 G1 X20 Z10N170 G42 X20 Z2N180 G1 ...

  • Page 14

    Collection of Part Program Examples14O20O100O40O60O80206080120160O40Diagram 88 Contour Definition%O7013(EXAMPLE 13)N100 T101N110 G0 X102 Z2N115 G92 S2500N120 G96 S100 M3 M8N130 G71 U1 R1N140 G71 U.2 W.2 F.2 P160 Q240N150 G0 X40 Z2N160 G42 X20 Z2 F.2N170 G1 Z-20 F.2N180 X40N190 X60 Z-60N200 G2 Z-8...

  • Page 15

    Collection of Part Program Examples15O20O100O60O40O8020304070100130150R50Diagram 99 Contour Definition%O7014(EXAMPLE 14)N100 G0 X200 Z200N110 T101N120 G0 X40 Z10N125 G92 S2500N130 G96 S100 M8 M3N140 G0 X82 Z2N150 G71 U1 R.5N160 G71 U.3 W.3 F.5 P190 Q280N170 G0 X100 Z100N180 T202N185 G96 S120N190 ...

  • Page 16

    Collection of Part Program Examples16O20O10020O60O204080110160R20Diagram 1010 Reflex Contour - Turned with Left Cutter%O7015(EXAMPLE 15)N100 G0 X200 Z200N110 T101N120 G0 X102 Z2N130 G92 S2500N140 G96 S100 M8 M3N150 G71 U1 R0.5N160 G71 U0.3 W0.3 F0.5 P180 Q240N170 G0 X40 Z10N180 G42 X20 Z2N190 G1 ...

  • Page 17

    Collection of Part Program Examples17O202030507080100130O40O80O100O40Diagram 1111 Contour Definition%O7016(EXAMPLE 16)N100 G0 X200 Z100N110 T101N120 G0 X100 Z10N130 G92 S2500N140 G96 S100 M8 M3N150 G71 U1 R0.5N160 G71 U0.3 W0.3 F0.5 P340 Q410N170 G0 X82 Z-70N180 G71 U0.3 F0.5 P430 Q480N190 G0 Z10...

  • Page 18

    Collection of Part Program Examples18Smoothing definition is kept on to be executed entirely, but in one step, independent ofroughing cycle.

  • Page 19

    Collection of Part Program Examples19O20O100O60O8020303525O401513015052525Diagram 1212 Cycles%O7017(EXAMPLE 17)N100 G0 X200 Z200N110 T101 (ROUGHING CUTTER)N120 G0 X98 Z6N130 G92 S3500N140 G96 S150 F0.5 M3 M8/1 N150 G72 W1 R0.5/1 N160 G72 P180 Q240 U0.3 W0.3F0.5 N170 G0 X200 Z200N180 T202 (SMOOTHI...

  • Page 20

    Collection of Part Program Examples20O24O8O3313101x45°O502x15°O32161616162x15°7.530°13. ábra13 Subprogram Technique%O7018(EXAMPLE 18)N100 G0 X200 Z200N110 T101 (SIDE CUTTER)N120 G0 X62 Z10N130 G92 S3500N140 G96 S150 M8 M3N150 G79 X-1 Z5 F0.2N160 Z3N170 Z1N180 Z0N190 G0 X200 Z200N200 G97 S100...

  • Page 21

    Collection of Part Program Examples21%O7019(EXAMPLE 19)N100 T202(ATM 8 DRILL)N110 S1000 M3 F0.2 M8N120 G0 X0 Z5N130 G1 Z-17N140 G4 P1N150 G0 Z100 N160 T303 (ATM 20 DRILL)N170 S1000 M3 F0.2 M8N180 G0 X0 Z5N190 G1 Z-10.5N200 G4 P1N210 G0 X0 Z10N220 T333 (ATM 20 DRILL)N230 G0 G42 X28 Z1.5N240 G1 X24...

  • Page 22

    Collection of Part Program Examples22Diagram 1414 Drilling cycles (Simple Drilling Cycle)%O7020(EXAMPLE 20)N100 G0 X200 Z200N110 T101 (SIDE CUTTER)N120 G0 X82 Z6N130 G92 S3500N140 G96 S150 F0.5 M3 M8N150 G79 X-1 Z5N160 Z3N170 Z1N180 Z0N190 G97 S500 N200 G0 X100 Z100N210 T303 (DRILL)N220 G17 G0 X0...

  • Page 23

    Collection of Part Program Examples23where the one-time drilling is programmed at address Q, then after lifting the distance the basepoint of previous drilling is to be approached at rapid traverse is specified at address E.In case the bore length demands automatic chip break, line N230 is modifi...

  • Page 24

    Collection of Part Program Examples24O20O100O60O802030#2#3O#5#4130150#3#3#6Diagram 1515 Parameter ProgrammingIn this example a recessing line is prepared. Number, width and depth of recessing maychange. When defining width, consider that the program first picks out most part of thematerial with a...

  • Page 25

    Collection of Part Program Examples25

x