Navigation

  • Page 1

    Laser engraving machineJinan Ruofen Laser Machinery Co.,LtdWebsite: actionURI(http://www.ruofencnc.com):www.ruofencnc.comService Contact information :Email: actionURI(mailto:service@ruofencnc.com):service@ruofencnc.comSkype:lifancncPlease send us your Order No. , we will do our best service for y...

  • Page 2

    1.去除机器上所有的包装,木箱,薄膜 等 (小心钉子 ,注意安全)Remove all the package recover the machine like the wood ,plastic filmand so on (be careful for the nails )2.打开机器上的大盖,侧门,及前门 ,取出里面的所以发货配件 :冷水机/水...

  • Page 3

    Exhaust fan pipe

  • Page 4

    Air pumpwrenchSoftdogCableChillerWater pump

  • Page 5

    Exhaust fanExhaust fanRotary axisLaser tube

  • Page 6

    3.打开机器前盖,剪掉 x 轴和 y 轴皮带上面的扎带,并取出光盘等,手轻轻移动激光头,移动到台面的中间位置。when you open the front door ,please cut the tie on the belt of the X-axisand Y-axi, get the CD , you can move the laser head to the center of thewo...

  • Page 7

    (2) 激光管上面有出光口和反射端,将出光口靠近第一反光镜(低压端),全反射端在另一头(高压端),全反射端在另一头(高压端)低压线接在激光管出光口这一端,高压线接在全反射端。There is two ends of the laser tube ,one is ...

  • Page 8

    (3) 有保护套的带上保护带,没有保护套的多缠防水高压胶带,激光管出光口是出水口。在上面,激光管全反射端是进水口,在下面,接上硅胶管,原则是低进高出。If it have the plastic protective sleeve , please cover the protective tape ,If ...

  • Page 9

    The installation method of the water chiller / water pump:(1)冷水机 :将冷水机的进/出水口,分别用硅胶管连接在机器上的出/进水口,并且连上航空插头(水保护线)water chiller: you should connect the water inlet and water outlet of waterchiller to the wat...

  • Page 10

    (2)水泵 :将水泵的出水口用硅胶管连接到机器上的进水口,并且用另一根硅胶管直接连接到机器的出水口,一端投入水箱中。water pump : use the silicone tube connect the water outlet of the waterpump with the water inlet of the laser machine . Then u...

  • Page 11

    The installation method of the air pump :Connect the air outlet of the airpump with the air inlet of the laser machine . (Air inlet )7.安装风机 :将风机的抽风口与机器上的伸缩管连接。

  • Page 12

    The installation method of the dust collector : Connect the exhaust port ofthe dust collector with the telescopic pipe of the laser machine .

  • Page 13

    8. 安装地线 :一定要安全接地,找一根线一头连到机器的接地端子,另一头接在钢筋上,埋在地上,钢筋要埋入地面 1.5 米,如果在潮湿的地方,钢筋埋入地面可以浅一些。The installation method of the Ground :must connect the ground securi...

  • Page 14

    9. 重新检查安装的配件是否正确安装,也要检查电源部分,接线头是否有掉落的和碰坏的You should check the parts of the machine is right installation , theElectrical accessories and line is whether drop , damage .10. 机器上要求使用 220v 的电压 ,如当地...

  • Page 15

    First you supply the power to the water chiller ,you should check thesilicone tube what make water , special water flow is whether normal .12. 连接电源 :将正确电压 220v 连到机器上的电源进口,打开急停和电锁,看通电是否正常,都打开后 ,在控制面板上...

  • Page 16

  • Page 17

    13. 将加密狗插到电脑上,并且将光盘里的内容拷贝到电脑上,用蓝色数据线将设备的板卡和电脑连接,给设备通电,正确安装软件。plug the softdog in the computer , copy the data of the CD to thecomputer ,use the blue data cable to connect the computer...

  • Page 18

    14. 打开电脑桌面的 Lasercut 图标,在这区域的任意位置话一个 40*40 圆形,加工方式是切割, 速度是 100 ,功率为 1 ,下载到机器里 , 将激光头移到适当位置,点 TEXT ,看能否正常走边框,如正常,点 START ,开始工作 。Open the Las...

  • Page 19

  • Page 20

  • Abstract

    First you supply the power to the water chiller ,you should check thesilicone tube what make water , special water flow is whether normal .12. 连接电源 :将正确电压 220v 连到机器上的电源进口,打开急停和电锁,看通电是否正常,都打开后 ,在控制面板上面按“前后左右 ”键,看激光头能否正常移动。Connect the power : connect the 220v power to the laser power , open theurgent stop and the power locks in order to see whether it is the normalpower ,press ESC twice ,then you can press the up-down-right-left on theLeetro or Philicam control panel to see the laser head is normal move .

x