Navigation

  • Page 1

    1Plasma cutting machine user manualJinan Ruofen Laser Machinery Co.,LtdWebsite: actionURI(http://www.ruofencnc.com):www.ruofencnc.comService Contact information :Email: actionURI(mailto:service@ruofencnc.com):service@ruofencnc.comSkype:lifancncPlease send us your Order No. , we will do our best s...

  • Page 2

    2Plasma cutting machine install manualCONTENTS1. Install machine ………………………………………..Page32. Adjusting ……………………………………………… Page133. Maintenance…………………………………….………Page194. Other points ………………...

  • Page 3

    3SafetyPlasma Cutting Machine are designed and built with ample safetyconsideration. However, proper installing and operating the machine canincrease your safety.DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT CASUALLYWITHOUT READING THIS MANUAL THROUGHOUT.Attention:*Before connect all the lines...

  • Page 4

    42.Connect lines in the control boxPhoto 1.-Machine electric parts connectinginput three phase 380v andone zero wire,blue wire isN zero wire ,three blackwire is L fire wire .Connecttheplasmapower ,three phase 380v

  • Page 5

    5Photo 2.—Plasma Power connectAdjust currentCheck airCuttingArc lineMaterial holderconnectorSign linePlasma headconnector

  • Page 6

    6Photo 3- Material holderAttention:* Ground function.Must touch with material when working* This holder can put any place of the material.* During working process , Do Not touch this holder.Material holderThis is holderfor materialAir compressorAir compressor380v

  • Page 7

    7Photo 4—Air compressor power connectPhoto 5-Air compressor connector with plasma powerExhaust pressureat least 0.8MPaAir compressor connectwith plasma power

  • Page 8

    8Photo 6- Air compressor connect with plasma powerConnect the aircompressor

  • Page 9

    9Photo 7 -- Open green buttonOperating panelPower swithEmergency stop

  • Page 10

    10Photo 8 -- Operating systemAttention:If screen show is not English , you can press G G 3 , screen will show as follow ,youchoose English , it will be ok.Main menuU disk,uploadthe file

  • Page 11

    11Photo 9-- change English show3. Set up the parameterPress system

  • Page 12

    12

  • Page 13

    13Chapter 2AdjustingDuring work, there need adjust according different material.First step :Adjusting Air Pressure

  • Page 14

    14Photo 10. Air pressure adjustingAttention:* Need pull button up then adjusting. When finish, please put down this button.* High thickness material need higher air pressure40--63A : air pressure :0.3---0.6MPa100--200A: air pressure :0.5--0.7MpaStep 1.open Plasma powerStep 2.Press the button into...

  • Page 15

    15Step 3.Adjusting Air pressure on 0.5MpaStep 4. Press the button into Cutting (Photo 11)and start to workPhoto 11--Current AdjustingSecond Step: Adjusting Current according to differentPhoto 12--Current Adjusting ( See attachment suggestion)Attention:*Adjusting current when working according to ...

  • Page 16

    16Operation:After adjusting, now let’s start to operate.1.move plasma head to left bottom of working piecePress X+ X- Y+ Y- ,move the x axis and y axis left bottom ofworking piece .as picture Photo 13Photo 132.upload the file , plug the U disk , press EDIT on the screen ,then pressUSB, again pr...

  • Page 17

    17EditUSBFileInputENTER

  • Page 18

    183. Adjust torch height :This is height value,1-3mm about set 90,100mm about set 105.Long time pressthis buttonShow thisF buttonChangeworking speedTorch height upTorch height downStart button

  • Page 19

    19Chapter 3MaintenanceChange the ElectrodePull down the head of water pipe from plasma head*From Left direction to Right sideLoosen Big electrodeby spannerThen press this buttonTwo timesLast press thisbutton

  • Page 20

    20Loosen small electrode by spanner then put it out by hand.*Direction same as Big electrode.Other points :1. Put material flat before working2. Cleaning Rail and insert oil before work off3. Power off when change Nozzle and electrode4. Fulfill water into water pump during work process5. Adopt ...

  • Page 21

    21Looking forward your reply.AttachmentNo.1Material NameThicknessmmCurrentAmAir PressureMpaSpeed(M/Min)Steel0.3200.64.50.6250.541.0400.651.5500.642.0550.653.53.0700.653TitaniumSteel0.5200.550.8250.551.0300.554.81.5400.64.5Our Service Departments hereby as follow:Quality First ,Service First ,.Cus...

  • Page 22

    22

  • Abstract

    22

x