Navigation

  • Page 1

    CNC S4000CNC S3000PROGRAMMINGFUNCTIONS

  • Page 2

    he programming functions listed on the following pages areavailable only on the CNC models whose symbols appear belowthe blue band containing the definition of the function.The correspondence of these symbols with the different modelsis indicated in the key reproduced at the bottom of each page.C...

  • Page 3

    1S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G00 (G0)Axis rapid positioningG00 AxisAxis R(or, alternatively,)Enabled: only in the block in which it is programmed.GENERAL G-FUNCTIONSG01 (G1)Linear interpolationG01 AxisEnabled: (default) until aor ais programmed.G02G03G02 (G2)Clockwise...

  • Page 4

    2S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G09 (G9)Deceleration at block endG09 X... Y... Z...Enabled: only in the block in which it is programmed.General G-FunctionsG10 First point or circle that defines a straight lineG10 X... Y... [I...]X,Y:I:circle center or supportingpoint coo...

  • Page 5

    G14G14Cancels MASTER-SLAVE axes (G15)(Only with Master-Slave option)G15 MASTER-SLAVE axes (Only with Master-Slave option)G15 SLAVE MASTER [I...]SLAVE:MASTER:I:G14name of “SLAVE” axis.name of “MASTER” axis.scale (I=1 by default).until ais programmedEnabled:.G16 Axis exchangeG16 Axis1 Axis2...

  • Page 6

    4S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035General G-FunctionsG19Enabled: until aor ais programmed.G17G18G19Plane selection (YZ is the machining plane, X is theperpendicular axis)G21 ChamferG21 J...J:Chamfer value (distance fromthe vertex).only in the block in which it isprogrammed...

  • Page 7

    General G-Functions5S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G25G25 Cancels G26G26G26Enabled: until ais programmed.G25G26 Axis reversal compensation (default on)G27First point of a SPLINEcurve linking a series of at least 5 pointsG27 X... Y... [I...] [Q...] [D1=1]X, Y:I:Q:D1=1:G29...

  • Page 8

    6S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035General G-FunctionsG31 [I...] [Q...] [D14=...]I:Q:D14:G30minimum speed, (I=0 by default).multiplication factor for machine acceleration (Q=1 by default).corner rounding coefficient (between 2 and 6). The higher the value ofD14, the softer ...

  • Page 9

    General G-Functions7S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G40 [K...] [X... Y...]K:K1:K2:KX, Yselects profile exit mode:automatic profile exit with a straight line perpendicular to thelast programmed element.automatic profile exit with a semicircle tangent to the lastprogrammed ...

  • Page 10

    8S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035General G-FunctionsD0=1:D1=1:D2=1:G666G40:an alternative to Q. Enables a tool/profile collision control. Thiseliminates the profile elements that, because of the radius offset,would cause a change of tool direction and possible gouging. To...

  • Page 11

    General G-Functions9S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G49 Kn [I...]Kn:I:I:G49recall cutter compensation (n).finish stock value.cutter radius.until aor a T for tool change is programmed.G49 I...Enabled:G49 Defines cylindrical mill radiusG26G50G50 Cancels the offset / rotatio...

  • Page 12

    10S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035General G-FunctionsG52 [X...] [Y...] [Z...] [I]X, Y, Z:I:G52coordinates of the new origin with respect to the main originincremental coordinates of the new origin (with respect to the lastprogrammed origin).until awithout parameters is pr...

  • Page 13

    General G-Functions11S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G26G56Enabled: until another mirror function or ais programmed.G53G56Z-mirror machining(change sign to Z coordinates)G26G57Enabled: until another mirror function or ais programmed.G53G57XY-mirror machining(change sign t...

  • Page 14

    General G-Functions12S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G62 K...K:K1:K2:type of coordinates.absolute coordinates.incremental coordinates, with respect to circle starting point.G62Type of coordinates for the definitionof circle center in G2/G3G26G67G67 Cancels G68/G69 static ...

  • Page 15

    General G-Functions13S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G68 [A...] [B...] [C...] [X...] [Y..] [Z...] [D1=...]ABC:X, Y, Z:D1=...G67,,Enabled:table rotation values. The system calculates the new position of thetool with respect to part zero after the rotation of the table.disp...

  • Page 16

    General G-Functions14S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035L:KLKLnumber of the internal subprogram (from L=0 to L=99) or name of theexternal subprogram (LNAME:)The programming order of theandparameters must beabsolutely respected. Therefore, first program parameterandthen .Warn...

  • Page 17

    General G-Functions15S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035D0=1D0=2D0=3D1= :D2= :D3= :D4= :D6= :D7= :D8=1:D9= :from the center toward the border, with Z increments onlyfrom the center toward the border, with increments in X, Y, Zdefines a special use of G77 for milling profiled...

  • Page 18

    General G-Functions16S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035D1=:D2=:pocket starting depth.pass depth.D3=:D4=:D6=:D7=:D9=:D10:D10=0D10=1D11:D11=0 (D12)=D11=1 (D12)=D11=2 (D12)=D12=: D11pocket bottom depth.clearance distance (default value D4 = 2 mm).wall taper rate (default value...

  • Page 19

    General G-Functions17S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035D5=:D6=:D7=:D9=:radius value for tool automatic approach and exit during the finishpass (default value D5 = I).wall taper rate (default value D6=0 - vertical wall).percentage of feed rate variation during depth incremen...

  • Page 20

    18S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035General G-FunctionsG82[X... Y...] Z... I... J... [Q...] [K...] [F...][D0=...] [D7=1] [D8=...] [D9=1] [D10=...][D11=...] [D12=...] [D13=...] [D14=...]G82 Deep mixed drilling cycleX, Y:Z:hole coordinates.hole bottom plane.I:J:QKFD0=depth in...

  • Page 21

    General G-Functions19S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035X, Y:Z:hole coordinates.hole bottom plane.I:J:Qdepth increment prior to (tool)return for chip discharge.hole starting plane and toolretraction plane for chipdischarge.:Z - axis clearance plane.G83 [X... Y...] Z... J... ...

  • Page 22

    D8:multiplication coefficient of the tapping rise speed with spindle andtransducer (default D8=1).D9=1: never mind where the machine is, the cycle is execute in XYposition, without to programming XY (D9=0 by default).until a new fixed cycle or ais programmed.Enabled:G80General G-Functions20S4060D...

  • Page 23

    General G-Functions21S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G89[X... Y...] Z... J... [I...] [K...] [Q...] [F...] [S...][D9=1] [D10=...] [D14=...] [D15=...][D16=...] [D17=...] [D18=...] [D19=...][D20=...] [D21=...] [D22=...] [D23=...]G89Differentiated drilling fixed cycle(Only fo...

  • Page 24

    D9=1D10=: never mind where the machine is, the cycle is executed in XY position,without to program XY (D9=0 by default).: rapid detachment value after each performed increase I (D10=0 bydefault).no detach, K pause every I mm.D10 detach, K pause every I mm.D10 mm detach without pausing K after I m...

  • Page 25

    General G-Functions23S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G93 F...F:G92G93 G94 G95Enabled: until a, or a,,with new F-values is programmed.new feed rate.G93 Feed rate defined as inverse of block execution timeG92 FF:G92G93 G94 G95the new feed rate overrides all F functions prog...

  • Page 26

    General G-Functions24S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Metric system programmingwith CNC inch configurationG201 J... [K...]J:KK1K2G200:cylinder radius in millimeters.specifies the unit of measure for the rotary axis coordinates:degrees (default).millimeters.until ais progra...

  • Page 27

    General G-Functions25S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G721 I... J... K... [Q...] [D0=...]IJKQQ1Q2D0D0=1D0=2:::::distance between points (alternative to J).number of points (alternative to I).identifier of the profile stored with G711 (from 31 to 40).processing mode for the...

  • Page 28

    26S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035General G-FunctionsG730G730 Cancels G731 (Only for S3000 Series CNCs)IJQD0D0=1D0=0D1=::::::lowest feed rate allowed (I=200 mm/min by default).angle below which no feed rate compensation is applied (J=7 bydefault).multiplication factor for...

  • Page 29

    General G-Functions27S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G734G734 Spiral milling: executionD0=D0=1D0=0D1=D8=:::request for graphic display of the tool path. (If not programmed,D0=1).: display off.: display on.geometric filter on the programmed points. All the points whosedist...

  • Page 30

    28S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035General G-FunctionsQ:K1:number of the section profile (from Q1 to Q10). Q=1 by default.if the section profile contains the K1 parameter, passes are calculatedaccording to the I distance programmed in G736. If K1 is notprogrammed, passes w...

  • Page 31

    General G-Functions29S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G26G746G746 Defers G748 cycleABCD0=D0=1D0=0G740,,EnabledNote: axis name.:selects the operating mode:the table always rotates about the tool tip.(default) the table rotates about the point where the tool tipwas when the ...

  • Page 32

    General G-Functions30S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G751 [TRS X...] [TRS Y...] [TRS Z...][ROT X...] [ROT Y...] [ROT Z...][SCA X...] [SCA Y...] [SCA Z...]G751 Rotation/offset in spaceG78TRS X:TRS Y:TRS Z:ROT X:ROT Y:ROT Z:SCA X:SCA Y:SCA Z:G750X - axis offset by a given v...

  • Page 33

    General G-Functions31S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Q0Q1Q2an error signal (ERR 98) is displayed.all the points outside the limits are projected on the limits.all the points outside the limits are eliminated.(only with Q1)(only with Q1)F:D0=:D1=:D2=:D3=:D4:D4=0:D4=1:D5:D5...

  • Page 34

    G777 Z... J... I... [Q...] [D1=...] [D2=...][D3=...] [D4=...] [D5=...] [D6=...] [D7=1]Z:J:I:Q:pocket bottom depthstarting depth.pass depth.clearance height for tool rapid out moves (Q=J+2 by default).D1=:D2=:D3=:D4=:D5=:D6=:D7=1:.inclined pass angle (D1=0 by default).finish stock allowance (D2=0 ...

  • Page 35

    General G-Functions33S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G26G71G782 X... Y... Z... J... I... [Q...] [K...] [F...] D1=... D2=...[D3=...] [D4=...] [D5=...][D6=...] [D8=...] [D7=1][D10=...] [D11=...] [D12=...] [D13=...] [D14=...]X, Y, D1, D2, D3, D4, D5, D6Z, J, I, Q, K, F, D0, ...

  • Page 36

    General G-Functions34S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035X, Y, D1, D2, D3, D4, D5, D6Z, J, I, Q, K, F, D0, D7, D8G86parameters: refer to grid pattern machiningcycles.parameters: refer to.D8=:scaling factor for rapid positioning feed (value include between 0and 1; D8=1 by defa...

  • Page 37

    General G-Functions35S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035D4=angular distance between holes (if D4 is omitted, figures will be evenlydistributed over 360°).X,Y:D1=D2=D3=circumference centercoor-dinates.number of holes.circumference radius withsign. If the radius is positive,h...

  • Page 38

    General G-Functions36S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G791 X... Y... Z... J... [I...] [Q...] [K...] [F...]D1=... D2=... [D3=...] [D4=...] [D5=...][D8=...] [D10=...] [D11=...] [D13=...]X, Y, D1, D2, D3, D4, D5Z, J, I, Q, K, F, D8, D10, D11, D13G81parameters: refer to circum...

  • Page 39

    37S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035General G-FunctionsG795 X... Y... Z... J... [Q...] [K...] [F...]D1=... D2=... [D0=...] [D3=...] [D4=...] [D5=...] [D7=...]X, Y, D1, D2, D3, D4, D5Z, J, Q, K, F, D8G85parameters: refer to circumference pattern Drilling.parameters: refer to...

  • Page 40

    General G-Functions38S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Axis: name of the machine axis to which the compensation is to be applied.until cycle / program end.Enabled:G817 AxisG26G817Tool length offset on an axisnon-orthogonal to the machining planeEnabled: only in the block in...

  • Page 41

    General G-Functions39S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Axis1 Axis2Axis3, etc..:G850,Enabled:defines the axes to be offset. The axis displacement /handwheel turn depends on the selected handwheel pitch.until ais programmed.G851 Axis1 Axis2 Axis3 etc..G26G71G26G851 Part origi...

  • Page 42

    General G-Functions40S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G910G26G71G26G910 Cancels G911The block containing the wrong instruction will be partially executed:machining will be stopped when an axis reaches its travel limit and anerror message will be displayed.until ais program...

  • Page 43

    41S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035IJQK:radius of the circle in mm of the circular mill path (if not programmedI=1).:profile increase in mm between circles (if not programmed J=1).:machining allowance (if not programmed Q=0).:machining mode selection:flush machining.not fl...

  • Page 44

    Copying G-Functions42S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035COPYING G-FUNCTIONSG877 Limits, mode and copying planeG877 PLANE K... J...PLANEK:K0K1K2J:J0J1J2J3J4J5J7J8J9J10J11:plane on which the polygon defining the copying area limits lies(XY or YZ or XZ).defines copying plane:=X...

  • Page 45

    43S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Copying G-FunctionsG880 Profile end in copying mode 11G880The profile to be copied shall be programmed between aandacode.G881G880G881 Copying cycle startG881 X... Y... I... K... Q... F...XYZ:I:K:Q:F:G888G888.or orEnabled:K1K2XYZXYZQ1:Q0.5...

  • Page 46

    44S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Copying G-FunctionsK:K0K1K2Q:D0=0:D0=1:D1=0:D1=1:D1=2:D1=3:AXES:XYXYZC:NAME:For the S3000 Series:For the S4000 Series:G882LNAME:DLG:NAME;LA:\NAME;LH:NAME;LNOME:L\DIR\NOME;point storing format:ASCII format (default).S3000 binary format (on...

  • Page 47

    45S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Copying G-FunctionsG884 [X...] [Y...] [Z...] [Q...]X,Y,Z:Q:(X... Y... or X... Z... or Y... Z...) coordinates of pass rotation center (pole)(pole inside copying limits).limit angle for copying cycle end. The default value is Q=180° withre...

  • Page 48

    46S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035G890Shall be programmed in MDI after thedefining the angle of rotation.G891G890 Zeroing deflections with inclined probesG891 [ROTX...] [ROTY...] [ROTZ...]ROTX...::ROTZ...:rotation about X-axis.rotation about Y-axis.rotation about Z-axis.R...

  • Page 49

    Logical Mathematical Operators47S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035LOGICALMATHEMATICAL OPERATORSDecisional operators=><>=<=<>equal togreater thanless thangreater than or equal toless than or equal todifferent fromEx.: {P24 <= P18}L22Parameters are identi...

  • Page 50

    48S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Character String EngravingCHARACTER STRING ENGRAVINGString position (on a straight line)P7P8P9=X-coordinate of the 1st stringcharacter=Y-coordinate of the 1st stringcharacter=string angleP8P7P9XY0 pieceBA12VZCharacter sizeP1P2P3P4= base= ...

  • Page 51

    49S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Character String EngravingThe programming format is:WRITEL = CHARACTER STRING (on a straight line)WRITEC = CHARACTER STRING (on a circumference)NOTE: to execute a writing machining inorit is necessary toprogram inand insert an axis exchan...

  • Page 52

    Storing Geometric Elements50S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035STORING GEOMETRIC ELEMENTSStoring pointsPoint defined by Cartesian coordinatesEp = G20 Xp YpEpYpXpOPoint defined by polar coordinatesG76Ep = G20 Xp YpG75EpYpXpOPoint defined by Cartesian coordinates referredto an...

  • Page 53

    Storing Geometric Elements51S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Point as intersection of two straight linesEp = G13 X… Y… J…,G13 X… Y… J…Ep = Er1, Er2EpYOXEr2Er1Point as intersection of two circlesEp1 =G20 X… Y… I…,G20X… Y… I…Ep2 =G20 X… Y… I…,G2...

  • Page 54

    52S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Storing Geometric ElementsStoring straight linesStraight line point - angleEr = G13 Xp Yp JrEr = G13 Ep JrErYpXpOEpJrXYStraight line circle - angleEr = G13 Xc Yc Ic JrEr = G13 Ec JrErYcXcOEcJrXYIcStraight line through two pointsEr = G10 X...

  • Page 55

    53S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Storing Geometric ElementsStraight line through a point and tangent to a circleEr = G10 Xp Yp,G11 Xc Yc IcEr = G10 Ep, G11 EcYpXpOEpXYYcXcEcIcErStraight line tangent to a circle andpassing through a pointEr = G10 Xc Yc Ic,G11 Xp YpEr = G1...

  • Page 56

    54S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Storing Geometric ElementsStoring circlesCircle of known center and radiusEc1= G20 Xc1 Yc1 Ic1Ec2= G51 Xo Yo Jo,G20 Xc2 Yc2 Ic2Ec2= Eo, G20 Xc2 Yc2 Ic2Ec1EoYoXc1OXYYc1XoIc1Xc2Ic2Yc2Ec2JoCircle of known radius tangent to two straight lines...

  • Page 57

    55S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Storing Geometric ElementsCircle of known radius through two circlesEc3 = G20 Xc1 Yc1 Ic1,G21 Ic3,G20 Xc2 Yc2 Ic2Ec3 = Ec1, G21 Ic3, Ec2OXYErEc3Ic1Ec2Ec1Ic2Ic3Circle through a point and tangent to a straight lineEc = G20 Xp Yp, G21 Ic,G13...

  • Page 58

    56S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Storing Geometric ElementsCircle through three pointsEc = G10 Xp1 Yp1,G20 Xp2 Yp2,G11 Xp3 Yp3Ec = G10 Ep1, G20 Ep2,G11 Ep3Circle with center in a point and tangentto a straight lineEc = G21 Xct Yct,G13 Xr Yr JrEc = G21 Ect, ErCircle with ...

  • Page 59

    57S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Storing Geometric ElementsConcentric circles at a given distanceEc2 = Ec1 Qd1Ec3 = Ec1 Q-d2Concentric to a pre-defined circleEc2 = Ec1 I2Circle with reverse directionEc2 = -Ec1OXYEc2Ec1Circle with center in a point and tangent to a circle...

  • Page 60

    58S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Storing Geometric ElementsStoring origin offset/rotationCircle tangent to two elements in a point(belonging to one of the two elements)Ec2 = Er, G20 Xp1Yp1, Ec1OXYP1ErEc1Ec2Direct definitionEo = G51 Xp Yp JoOJoYpXXpYIndirect definitionEo ...

  • Page 61

    59S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Storing distanceDistance between two pointsEd = G20 Xp1 Yp1,G20 Xp2 Yp2Ed = Ep1, Ep2OXYEp2EdEp1Distance between a point and a stright lineEd = G20 Xp Yp,G13 Xr Yr JrEd = Ep, ErOXYErEdEpDistance between two straight linesEd = Er1, Er2Ed = ...

  • Page 62

    60S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035DISPLAY PARAMETERS$0$1 M...X...I...Y...J...$2 X... I... Y...J...K...Q...X...I...Y...J...K...Q...$3$4$3$5$6$7$8$9cancels the drawing on the screen, without modifying the currentparameters.setting of the display in two dimensions, where:pla...

  • Page 63

    61S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Display Parameters$10$11$12$13$20$21.$21K... I...blue.pink.white.black.cancelswhen the plan view mode is enabled, allows to perform a m a c h i n i n gsimulation by drawing a series of circles on the tool center path.Circles diameter is t...

  • Page 64

    62S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035Outputting P ParametersOUTPUTTING P PARAMETERSOPEN n, NAMEn=2NAME.000S4000:NAME.001 .002S3000:NAMENAMENAMEn=3NAMEn=4NAMEFORMAT n,STRING1 ####.###defines the name of the program into which theparameters will be stored, where:creation of th...

  • Page 65

    63S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035PRINT n, P...,P..., P...nFORMATP...P0P199CLOSEPRINTEnables the writing of a block in the program with theformatdefined by thefunction;are the parameters to be printed, fromto,separated by commas.closes the printing file. It must be progra...

  • Page 66

    64S4060DS4045PS3045PS4040GES3040GES4045S3045S4040S3040S3035IndexGeneral G-FunctionsCopying G-FunctionsLogical mathematical operatorsCharacter engraving stringsStoring geometric elements.............................Page1.............................Page 42....................Page 47..................

  • Page 67

  • Page 68

    SELCA S.p.A. - Corso Vercelli, 123 - 10015 IVREA (TO) ItalyTel. +39 0125 61.44.11 - Fax +39 0125 61.44.08www.selca.it - E-mail: marketing@selca.it

x