Navigation

  • Page 1

    SINUMERIK 840D/810D/FM-NC12.98 EditionShort GuideOperationUser Documentation

  • Page 2

    User DocumentationSINUMERIK840D/810D/FM-NCSINUMERIKOverview of SINUMERIK 840D/810D/FM-NC Documentation (12.98)BrochureCatalog OrderingInfo NC 60.1 *)Technical Info.NC 60.2Description of Functions Drive Functions *)Description of Functions– Basic Machine *) – Extended Functions– Special Fu...

  • Page 3

    SINUMERIK 840D/810D/FM-NCShort GuideOperation12.98 EditionValid forControlSoftware versionSINUMERIK 840D5SINUMERIK 840DE (Export version)5SINUMERIK 810D3SINUMERIK 810DE (Export version)3SINUMERIK FM-NC3

  • Page 4

    SINUMERIK® documentationPrinting historyBrief details of this edition and previous editions are listed below.The status of each edition is shown by the code in the "Remarks" column.Status code in the "Remarks" column:A .... New documentationB .... Unrevised reprint with new O...

  • Page 5

    12.98General information© Siemens AG 1998. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition0-5IntroductionMMC100.2MMC103ValidityUnless stated otherwise, this operator’s guide applies tothe SINUMERIK 840D/810D and SINUMERIK FM-NCcontrolsHow to use thisbo...

  • Page 6

    General information12.980-6© Siemens AG 1998 All rights reservedSINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition

  • Page 7

    12.98Contents© Siemens AG 1998. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition0-7List of SectionsOperator Control1Set-up2Manually Controlled Operation3Part Programming4Program Management5Automatic Mode6Alarms and Messages7

  • Page 8

    Contents12.980-8© Siemens AG 1998 All rights reservedSINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition

  • Page 9

    © Siemens AG 1998 All rights reserved.1-9SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1. Operator Control1.1 Key assignments slimline operator panel OP 0311-101.2 Key assignments slimline operator panel OP 0321-111.3 Key assignments operator panel1-121.4 Key assignments e...

  • Page 10

    1. Operator Control03.961-10© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.1 Key assignments slimline operator panel OP 031MMC100.2MMC103ABCDEFGHIJ7(89/KLMNO123-[PQRST= 0.+]UZ?!–-<>$"VWXY,\End1..n1 24 5683456*)7 1Machine ...

  • Page 11

    03.961. Operator Control© Siemens AG 1998 All rights reserved.1-11SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.2 Key assignments slimline operator panel OP 032MMC100.2MMC10324563QWERTYUIOPZXCVBNM,ASDFGHJKLCtrlAltDel1..nEnd689345012=/+-*/Del798101 1Machine area key 2Reca...

  • Page 12

    1. Operator Control03.961-12© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.3 Key assignments operator panelMMC100.2MMC103Meaning of the key symbols:The keys marked with * correspond to the US layout. 1..n GROUPCHANNEL *Switch over c...

  • Page 13

    03.961. Operator Control© Siemens AG 1998 All rights reserved.1-13SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.4 Key assignments external machine control panelMMC100.2MMC103Machine control panel for turning machinesMachine control panel for milling machines1423567814235...

  • Page 14

    1. Operator Control03.961-14© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.4 Key assignments external machine control panelMMC100.2MMC103 REPOS*Repos REFPOINT*Ref 3Incremental travel 4Program control RESET*Reset SINGLEBLOCK*Single...

  • Page 15

    03.961. Operator Control© Siemens AG 1998 All rights reserved.1-15SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.4 Key assignments external machine control panelMMC100.2MMC103 6Spindle controlSpindle override SPINDLESTOP*Spindle stop SPINDLESTART*Spindle start 7Feed con...

  • Page 16

    1. Operator Control03.961-16© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.5 Graphical user interfaceMMC100.2MMC103M0M0M0H0.000000H0.000000H0.000000M0M0+ X 900.000 mm 0.000 - Y -156.000 mm 0.000 + Z 230.000 m...

  • Page 17

    03.961. Operator Control© Siemens AG 1998 All rights reserved.1-17SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.5 Graphical user interfaceMMC100.2MMC103 6Mode 7Program name 8Channel operational messages 9Channel status display 10Information relating to the menu bar 11Wor...

  • Page 18

    1. Operator Control03.961-18© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.6 Operating areasMMC100.2MMC103The standard functions in the control are organized into thefollowing operating areas: Operating areasMAC...

  • Page 19

    03.961. Operator Control© Siemens AG 1998 All rights reserved.1-19SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.7 Operating principleMMC100.2MMC103The MMC 100.2 and MMC 103 provide a range of key andsoftkey assignments which have the same function in alloperating areas a...

  • Page 20

    1. Operator Control03.961-20© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.7 Operating principleMMC100.2MMC103Navigation in the menu window:?Change menu windows:Change the focus to theselected menu window. Scroll in the menu window:S...

  • Page 21

    03.961. Operator Control© Siemens AG 1998 All rights reserved.1-21SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.7 Operating principleMMC100.2MMC103Navigation in the directory tree:! Select directory/file:Position the cursor on thedesired directory/file.Open/close direct...

  • Page 22

    1. Operator Control03.961-22© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.7 Operating principleMMC100.2MMC103Edit inputs/values:If you want to editinputs/values, thecorresponding key is alwaysdisplayed automatically onthe right of th...

  • Page 23

    03.961. Operator Control© Siemens AG 1998 All rights reserved.1-23SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.7 Operating principleMMC100.2MMC103You can use the "Toggle" keyto select one of severaldefault values.3. Selection list (MMC 103):Display the presele...

  • Page 24

    1. Operator Control03.961-24© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.7 Operating principleMMC100.2MMC103Confirm/cancel input:OKConfirm input:Save the inputs and exit thecurrent menu (youautomatically return to thecalling menu).C...

  • Page 25

    03.961. Operator Control© Siemens AG 1998 All rights reserved.1-25SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition1.7 Operating principleMMC100.2MMC103Operation with the mouse:If you have installed a mouse,operation is facilitated asfollows:1 "click"1 click means:...

  • Page 26

    1. Operator Control03.961-26© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition

  • Page 27

    © Siemens AG 1998 All rights reserved.2-27SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2. Set-up2.1 Approach reference point2-282.2 Enter tool offsets2-292.3 Calculate tool offsets2-302.4 Enter/alter zero offset (MMC100.2)2-312.5 Enter/alter zero offset (MMC103)2-322.6 Sc...

  • Page 28

    2. Set-up03.962-28© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.1 Approach reference pointMMC100.2MMC103Caution:Position the axes if they are not already located at a safeposition.Always follow the axis movements directly on the mach...

  • Page 29

    03.962. Set-up© Siemens AG 1998 All rights reserved.2-29SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.2 Enter tool offsetsMMC100.2MMC103ParameterSelect "Parameter"operating area.TooloffsetSelect "Tool offset" menu.Choose the desiredfunction:T no.+T no...

  • Page 30

    2. Set-up03.962-30© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.3 Calculate tool offsetsMMC100.2MMC103ParameterSelect "Parameter"operating area.TooloffsetSelect "Tool offset" menu.Position cursor on desiredtool pa...

  • Page 31

    03.962. Set-up© Siemens AG 1998 All rights reserved.2-31SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.4 Enter/alter zero offset (MMC100.2)MMC100.2ParameterSelect "Parameter"operating area.ZerooffsetsSelect "Zero offsets" menu.OverviewSelect zero offse...

  • Page 32

    2. Set-up03.962-32© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.5 Enter/alter zero offset (MMC103)MMC103ParameterSelect "Parameter"operating area.ZerooffsetSelect "Overview of settablezero offsets" menu.Axes +Axes...

  • Page 33

    03.962. Set-up© Siemens AG 1998 All rights reserved.2-33SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.5 Enter/alter zero offset (MMC103)MMC103Position the cursor on thedesired field and enter/alterthe value.Please note:Changes in the zero offset are updated at entry.

  • Page 34

    2. Set-up03.962-34© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.6 Scratching method/determine zero offset (MMC100.2)MMC100.2ParameterSelect "Parameter"operating area.Select "Jog" mode.ZerooffsetsSelect "Zero ...

  • Page 35

    03.962. Set-up© Siemens AG 1998 All rights reserved.2-35SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.7 Scratching method/determine zero offset (MMC103)MMC103MachineSelect "Machine" operatingarea.ScratchingActive level, active zero offsetand active tool are sel...

  • Page 36

    2. Set-up03.962-36© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.8 Program the setting dataMMC100.2MMC103ParameterSelect "Parameter"operating area.SettingdataSelect the "Setting data"menu.Define operating statesusi...

  • Page 37

    03.962. Set-up© Siemens AG 1998 All rights reserved.2-37SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition2.8 Program the setting dataMMC100.2MMC103! Position the cursor on thedesired field and change thevalue, orselect a new value using the"Toggle" key.

  • Page 38

    2. Set-up03.962-38© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition

  • Page 39

    © Siemens AG 1998 All rights reserved.3-39SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition3. Manually Controlled Operation3.1 Jog/Jog-Inc mode3-403.2 MDA mode3-423.3 Teach In mode3-43

  • Page 40

    3. Manually Controlled Operation03.963-40© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition3.1 Jog/Jog-Inc modeMMC100.2MMC103MachineSelect "Machine"operating area.JogSelect "Jog" mode."Reference point approach"...

  • Page 41

    03.963. Manually Controlled Operation© Siemens AG 1998 All rights reserved.3-41SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition3.1 Jog/Jog-Inc modeMMC100.2MMC103Select/enter incrementvalue for traversingposition ("Inc"): ... Traverse axes in definedincrements, orI...

  • Page 42

    3. Manually Controlled Operation03.963-42© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition3.2 MDA modeMMC100.2MMC103MachineSelect "Machine"operating area.MDASelect "MDA" mode.In "Teach In" mode, it is only pos...

  • Page 43

    03.963. Manually Controlled Operation© Siemens AG 1998 All rights reserved.3-43SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition3.3 Teach In modeMMC100.2MMC103MachineSelect "Machine"operating area.MDASelect "MDA" mode.Select "Teach In" submode.In ...

  • Page 44

    3. Manually Controlled Operation03.963-44© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition3.3 Teach In modeMMC100.2MMC1032. Manual input of coordinates:• Enter coordinates oftraversing positions and• enter additional functions(prepara...

  • Page 45

    © Siemens AG 1998 All rights reserved.4-45SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4. Part Programming4.1 Select/enable workpiece/part program4-464.2 Open/edit part program4-474.3 Create new workpiece/part program4-494.4 Execute workpiece/part program4-504.5 Copy/past...

  • Page 46

    4. Part Programming03.964-46© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4.1 Select/enable workpiece/part programMMC100.2MMC103ProgramSelect "Program"operating area.Select workpiece/part program:Work-piecesSelect the level:...

  • Page 47

    03.964. Part Programming© Siemens AG 1998 All rights reserved.4-47SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4.2 Open/edit part programMMC100.2MMC103ProgramSelect "Program"operating area.Open part program:Position the cursor on thedesired file in the directory...

  • Page 48

    4. Part Programming03.964-48© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4.2 Open/edit part programMMC100.2MMC103Edit part program:OverwriteToggle between insert andoverwrite mode.MarkblockMark the beginning of block. Copybloc...

  • Page 49

    03.964. Part Programming© Siemens AG 1998 All rights reserved.4-49SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4.3 Create new workpiece/part programMMC100.2MMC103ProgramSelect "Program"operating area.Work-piecesPartprogramsSub-routinesSelect "Workpieces&quo...

  • Page 50

    4. Part Programming03.964-50© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4.4 Execute workpiece/part programMMC100.2MMC103ProgramSelect "Program" operatingarea. Work-piecesSelect workpiece:Mark the desired workpiecewith the...

  • Page 51

    03.964. Part Programming© Siemens AG 1998 All rights reserved.4-51SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4.5 Copy/paste, rename, delete, enableMMC100.2MMC103ProgramSelect "Program"operating area.Select the level and positionthe cursor on the desired filein...

  • Page 52

    4. Part Programming03.964-52© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4.5 Copy/paste, rename, delete, enableMMC100.2MMC103Delete program:DeleteDelete the program from thedirectory.Change enable:ChangeenableSet (x) or cancel ( ) en...

  • Page 53

    03.964. Part Programming© Siemens AG 1998 All rights reserved.4-53SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition4.6 Load/unload program (MMC 103)MMC103ProgramSelect "Program" operatingarea.Position the cursor on thedesired file in the directorytree.LoadLoad the p...

  • Page 54

    4. Part Programming03.964-54© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition

  • Page 55

    © Siemens AG 1998 All rights reserved.5-55SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5. Manage data5.1 Transfer data (MMC 100.2)5-565.2 Transfer data (MMC 103)5-595.3 Create new file/directory (MMC 103)5-615.4 Load/unload program (MMC 103)5-625.5 Copy/paste, delete (MMC...

  • Page 56

    5. Manage data03.965-56© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.1 Transfer data (MMC 100.2)MMC100.2ServicesSelect "Services"operating area.Read out data:Data outSelect "Data out" menu.Select interface:V.24-us...

  • Page 57

    03.965. Manage data© Siemens AG 1998 All rights reserved.5-57SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.1 Transfer data (MMC 100.2)MMC100.2Read in data:Data inSelect " Data in" menu.Select interface:V.24user• V.24 userV.24-PG/PC• V.24-PG/PCPosition the c...

  • Page 58

    5. Manage data03.965-58© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.1 Transfer data (MMC 100.2)MMC100.2StartOrganize data according tothe existing path:Path/workpiece from archivefileStore all files in the directory,irrespective of ...

  • Page 59

    03.965. Manage data© Siemens AG 1998 All rights reserved.5-59SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.2 Transfer data (MMC 103)MMC103ServicesSelect "Services"operating area.Read out data:Data outSelect "Programs/data"menu.Select data in the direc...

  • Page 60

    5. Manage data03.965-60© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.2 Transfer data (MMC 103)MMC103Read in data:Data inSelect "Programs/data"menu.Select data in the directorytree.Select source area:V.24• V.24 interfacePG...

  • Page 61

    03.965. Manage data© Siemens AG 1998 All rights reserved.5-61SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.3 Create new file/directory (MMC 103)MMC103ServicesSelect "Services" operatingarea.ManagedataSelect "Manage data" menu.New...Enter program name ...

  • Page 62

    5. Manage data03.965-62© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.4 Load/unload program (MMC 103)MMC103ServicesSelect "Services"operating area.ManagedataSelect "Manage data" menu.Position the cursor on thedesir...

  • Page 63

    03.965. Manage data© Siemens AG 1998 All rights reserved.5-63SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.5 Copy/paste, delete (MMC 103)MMC103ServicesSelect "Services"operating area.ManagedataSelect "Manage data" menu.Position the cursor on thesource...

  • Page 64

    5. Manage data03.965-64© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition5.6 Directory/file/archive properties (MMC 103)MMC103ServicesSelect "Services"operating area.ManagedataSelect "Manage data" menu.Position the curs...

  • Page 65

    © Siemens AG 1998 All rights reserved.6-65SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6. Automatic Mode6.1 Select workpiece/program6-666.2 Start/stop/cancel program6-676.3 Repos − Reposition after interruption6-686.4 Overstore6-706.5 Display program level6-716.6 Progra...

  • Page 66

    6. Automatic Mode03.966-66© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.1 Select workpiece/programMMC100.2MMC103MachineSelect "Machine"operating area.AUTOSelect "Automatic" mode.ProgramoverviewSelect "Program...

  • Page 67

    03.966. Automatic Mode© Siemens AG 1998 All rights reserved.6-67SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.2 Start/stop/cancel programMMC100.2MMC103MachineSelect "Machine"operating area.AUTOSelect "Automatic" mode.Please check that:No alarms are ac...

  • Page 68

    6. Automatic Mode03.966-68© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.3 Repos − Reposition after interruptionMMC100.2MMC103After a program interrupt ("NC Stop") you can move the toolaway from the contour in the manual m...

  • Page 69

    03.966. Automatic Mode© Siemens AG 1998 All rights reserved.6-69SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.3 Repos − Reposition after interruptionMMC100.2MMC103MachineSelect "Machine"operating area.AUTOSelect "Automatic" mode.Continue machining.

  • Page 70

    6. Automatic Mode03.966-70© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.4 OverstoreMMC100.2MMC103MachineSelect "Machine"operating area.AUTOSelect "Automatic" mode.Overstore with singleblock:The program automatical...

  • Page 71

    03.966. Automatic Mode© Siemens AG 1998 All rights reserved.6-71SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.5 Display program levelMMC100.2MMC103MachineSelect "Machine"operating area.AUTOSelect "Automatic" mode.ProgramlevelDisplay block numbers form...

  • Page 72

    6. Automatic Mode03.966-72© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.6 Program correctionMMC100.2MMC103MachineSelect "Machine"operating area.AUTOSelect "Automatic" mode.The control has detected a system error i...

  • Page 73

    03.966. Automatic Mode© Siemens AG 1998 All rights reserved.6-73SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.7 Execution from V.24 (MMC 100.2)MMC100.2MachineSelect "Machine"operating area.ProgramoverviewSelect "Program overview"menu.Executionfrom ext...

  • Page 74

    6. Automatic Mode03.966-74© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.8 Load/unload program from hard disk (MMC 103)MMC103MachineSelect "Machine"operating area.ProgramoverviewSelect "Program overview "menu.Posit...

  • Page 75

    03.966. Automatic Mode© Siemens AG 1998 All rights reserved.6-75SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition6.9 Execution from hard disk (MMC 103)MMC103MachineSelect "Machine"operating area.ProgramoverviewSelect "Program overview"menu.Position the cur...

  • Page 76

    6. Automatic Mode03.966-76© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition

  • Page 77

    © Siemens AG 1998 All rights reserved.7-77SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition7. Alarms and Messages7.1 Alarms/messages7-78

  • Page 78

    7. Alarms and Messages03.967-78© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition7.1 Alarms/messagesMMC100.2MMC103DiagnosisSelect "Diagnosis"operating area.Display alarms:AlarmsDisplay alarms with "alarmnumber", "d...

  • Page 79

    03.967. Alarms and Messages© Siemens AG 1998 All rights reserved.7-79SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition7.1 Alarms/messagesMMC100.2MMC103Display messages:MessagesDisplay PLC error messagesand PLC operationalmessages.Caution:PLC error messages must always be ackn...

  • Page 80

    7. Alarms and Messages03.967-80© Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition

  • Page 81

    SIEMENS AGA&D MC ISSuggestionsCorrectionsP.O. Box 3180D-91050 ErlangenFederal Republic of Germanyfor Publication/ManualSINUMERIK 840D/810D/FM-NC(Fax ++49 9131/98-1145)User DocumentationFromNameShort GuideOperationOrder No.:6FC5298-5AA10-0BP0Edition:12.98Company/DepartmentAddress______________...

x