Navigation

  • Page 1

    SINUMERIK 840D/840DiSINUMERIK 810D/FM-NCShort Guide10.2000 EditionUser DocumentationProgramming

  • Page 2

  • Page 3

    SINUMERIK 840D/840DiSINUMERIK 810D/FM-NCShort GuideProgramming10.00 EditionValid forControlSoftware versionSINUMERIK 840D6SINUMERIK 840DE (Export version)6SINUMERIK 840Di1SINUMERIK 840DiE (Export version)1SINUMEbcK 810D4SINUMERIK 810DE (Export version)4SINUMERIK FM-NC3

  • Page 4

    SINUMERIK® documentationPrinting historyBrief details of this edition and previous editions are listed below.The status of each edition is shown by the code in the "Remarks" column.Status code in the "Remarks" column:A .... New documentation.B .... Unrevised reprint with new ...

  • Page 5

    10.00General Information Siemens AG 1998. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition0-5IntroductionHow to use thisbookletThis booklet is a programming guidedescribing all the main programming steps.The aim is to provide the operator with some ...

  • Page 6

    General Information10.00 Siemens AG 2000. All rights reserved.0-6SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionStructure of the descriptionsThe system used in these descriptions is based on thefollowing scheme:Programming of the functionMeaning of the parametersExpla...

  • Page 7

    10.00General Information Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition0-7List of sections1. What is at the Beginning of the Program1-9Absolute and incremental dimensions, G90, G91................................................1-...

  • Page 8

    General Information10.00 Siemens AG 2000. All rights reserved.0-8SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionBore 4, CYCLE88.................................................................................................6-70Bore 5, CYCLE89............................

  • Page 9

     Siemens AG 2000. All rights reserved.1-9SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition1. What is at the Beginning of the ProgramAbsolute and incremental dimensions, G90, G911-10Zero offset, G54 to G571-12Selection of working plane G17 to G191-14

  • Page 10

    1. What is at the Beginning of the Program10.001-10 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionAbsolute and incremental dimensions, G90, G91ProgrammingN5 G0 G90 X25 Y15 Z2 LFN20 G1 G91 X80 F300 LFG90Absolute dimension input, al...

  • Page 11

    10.001. What is at the Beginning of the Program Siemens AG 2000. All rights reserved.1-11SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionAbsolute and incremental dimensions, G90, G91 (cont.)ProgrammingN5 G0 G90 X25 Z1N10 G1 Z-7.5 F0.2N20 G1 X40 Z-15N30 G1 G91 Z-10N40 G...

  • Page 12

    1. What is at the Beginning of the Program10.001-12 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionZero offset, G54 to G57ProgrammingN30...LFN40 G54 LFN50 G0 X30 Y75LFOther zero offsets: G55...G57, G505…G599ParametersX,Y,ZCoordin...

  • Page 13

    10.001. What is at the Beginning of the Program Siemens AG 2000. All rights reserved.1-13SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionZero offset, G54 to G57 (cont.)ProgrammingN10 G54N20 G0 Z0.2ParameterZCoordinates of the zero offsets (definition ofworkpiece coordi...

  • Page 14

    1. What is at the Beginning of the Program10.001-14 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionSelection of working plane G17 to G19ProgrammingN10 G0 X50 Z50 G17 D1 F1000 LFCommandWorking planeInfeed axisG17X/YZG18Z/XYG19Y/ZXPr...

  • Page 15

    10.001. What is at the Beginning of the Program Siemens AG 2000. All rights reserved.1-15SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionSelection of working plane, G17 to G19 (cont.)ProgrammingN10 G0 X10 Z20 G18 D1 F200In the basic setting, G17 is preset for milling (...

  • Page 16

    1. What is at the Beginning of the Program10.001-16 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition

  • Page 17

     Siemens AG 2000. All rights reserved.2-17SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition2. Programming Motion CommandsRapid traverse, G02-18Linear interpolation, G12-20Circular interpolation, G2/G32-22Radius programming, G2/G32-24Circular interpolation through interm...

  • Page 18

    2. Programming Motion Commands10.002-18 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionRapid traverse, G0ProgrammingN10G0X0 Y0Z3 LFParametersX, Y, ZCoordinates of the target pointZYXFast tool positioning in rapid traverse for milli...

  • Page 19

    10.002. Programming Motion Commands Siemens AG 2000. All rights reserved.2-19SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionRapid traverse, G0 (cont.)ProgrammingN20G0X25 Z1ParametersX, ZCoordinates of the target pointZX255060N80N20357.5Fast tool positioning in rapid t...

  • Page 20

    2. Programming Motion Commands10.002-20 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionLinear interpolation, G1ProgrammingN10 G0 G90 X10 Y10 Z1 S800 M3 LFN20G1Z-12 F500 LFN30 X30 Y35 Z-3 F700 LFParametersX, Y, ZCoordinates of the t...

  • Page 21

    10.002. Programming Motion Commands Siemens AG 2000. All rights reserved.2-21SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionLinear interpolation, G1 (cont.)ProgrammingN10 G17 S400 M3N20G0X40 Y-6 Z2N30G1Z-3 F40N40 X12 Y-20ParametersX, Y, ZCoordinates of the target poin...

  • Page 22

    2. Programming Motion Commands10.002-22 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionCircular interpolation, G2/G3ProgrammingN5 G0 G90 X35 Y60 LFN10G3 X50 Y45 I0 J-15 F500 LFParametersX, Y, ZCoordinates of the circle end pointI, ...

  • Page 23

    10.002. Programming Motion Commands Siemens AG 2000. All rights reserved.2-23SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionCircular interpolation, G2/G3 (cont.)ProgrammingN10 G0 X12 Z0N20G1 X40 Z-25 F0.2N30G3 X70 Z-75 I-3.335 K-29.25ParametersX, Y, ZCoordinates of th...

  • Page 24

    2. Programming Motion Commands10.002-24 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionRadius programming, G2/G3ProgrammingN20 G90 G0 X68 Z102N30 G90 G3 X20 Z150 CR=48 F300 LFParametersCRCircle radiusCR+Traversed angle ó 180°CR-T...

  • Page 25

    10.002. Programming Motion Commands Siemens AG 2000. All rights reserved.2-25SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionCircular interpolation through intermediate point, CIPProgrammingN10 CIP X87 Y20 I1=60 J1=35 LFParametersX, Y, ZCoordinates of the circle end po...

  • Page 26

    2. Programming Motion Commands10.002-26 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionCircular interpol. through interm. point, CIP (cont.)ProgrammingN90 G1 X40 Z-25N100 CIP X70 Z-75 I1=93.33 K1=-54.25ParametersX, ZCoordinates of ...

  • Page 27

    10.002. Programming Motion Commands Siemens AG 2000. All rights reserved.2-27SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionThread cutting, G33ProgrammingN20G33 Z22 K2 LFParametersZ, XThread end pointKThread lead for cylindrical threadIThread lead for face threadIThre...

  • Page 28

    2. Programming Motion Commands10.002-28 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionRigid tapping, G331/G332ProgrammingN40SPOS=0 LFN50G331 Z-50 K2 S500 LFN60G332 Z5 K2LFSPOS=0Change spindle to position control and put intopositi...

  • Page 29

    10.002. Programming Motion Commands Siemens AG 2000. All rights reserved.2-29SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionTapping with floating tapholder, G63ProgrammingN10G63 Z-50 M3 S...F...LFN20G63 Z4 M4F...LFG63For the retraction movement, you programanother blo...

  • Page 30

    2. Programming Motion Commands10.002-30 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionPolar coordinates G110, G111, G112ProgrammingN30G111 X40 Y35 Z40LFN40G3 RP... AP...LFG110Definition of pole, referred to tool position lastprogr...

  • Page 31

     Siemens AG 2000. All rights reserved.3-31SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition 3. Tool Offsets and CompensationsTool call3-32Cutter radius path compensation, G41/G423-33Tool nose radius compensation, G41/G423-34Activating/deactivating the collision detectio...

  • Page 32

    3. Tool Offsets and Compensations10.003-32 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition Tool callProgrammingN10 G18 T17 D8 LFT...Call tool numberD...Call tool offset, activate tool lengthcompensationTo make sure that the tool of...

  • Page 33

    10.003. Tool Offsets and Compensations Siemens AG 2000. All rights reserved.3-33SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition Cutter radius path compensation, G41/G42ProgrammingN10 G1 G17 G41 D8 X... Y... Z... F500 LFG41Call for cutter path compensation, tool intrav...

  • Page 34

    3. Tool Offsets and Compensations10.003-34 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition Tool nose radius compensation, G41/G42ProgrammingN5 G90 G0 G18 G41 D... X... Y... Z... LFG41Call for radius compensation, tool motion intrav...

  • Page 35

    10.003. Tool Offsets and Compensations Siemens AG 2000. All rights reserved.3-35SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition Activating/deactivating the collision detectionProgrammingN10 G41 X...Y...Z... CDON LFCDON Collision detection onCDOF Collision detection of...

  • Page 36

    3. Tool Offsets and Compensations10.003-36 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition Approach and exit the contour, NORM/KONTProgrammingKONT G41 G450 X... Y... Z... LFNORMThe tool travels directly along a straight lineand is ...

  • Page 37

    10.003. Tool Offsets and Compensations Siemens AG 2000. All rights reserved.3-37SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition Programmable contour travel mode, G450/G451ProgrammingN10 G41 G450 X... Y... Z... LFG450Transition circle, the tool travels aroundworkpiece ...

  • Page 38

    3. Tool Offsets and Compensations10.003-38 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition

  • Page 39

     Siemens AG 1998. All rights reserved.4-39SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition4. Programming Aids Assist the ProgrammerOverview of frame concept4-40Translating/rotating the coordinate system, TRANS/ROT 4-42Mirroring on the coordinate axes, MIRROR4-44Increas...

  • Page 40

    4. Programming Aids Assist the Programmer10.004-40 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionOverview of frame conceptProgrammingFor the three-dimensional description of the workpiececoordinate system, the following functions ...

  • Page 41

    10.00 4. Programming Aids Assist the Programmer Siemens AG 1998. All rights reserved.4-41SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionOverview of fr...

  • Page 42

    4. Programming Aids Assist the Programmer10.004-42 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionTranslating/rotating the coordinate system, TRANS/ROTProgrammingN30...G54 LFN40G90 TRANS X40 Y40 Z30 LFN50G90 AROT Z 30 LFTo switch o...

  • Page 43

    10.00 4. Programming Aids Assist the Programmer Siemens AG 1998. All rights reserved.4-43SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionTranslating/ro...

  • Page 44

    4. Programming Aids Assist the Programmer10.004-44 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionMirroring on the coordinate axes, MIRRORProgrammingN10MIRROR X0 LFSwitch off MIRROR (without defining axis)In all cases, the complete...

  • Page 45

    10.00 4. Programming Aids Assist the Programmer Siemens AG 1998. All rights reserved.4-45SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionIncreasing/red...

  • Page 46

    4. Programming Aids Assist the Programmer10.004-46 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition

  • Page 47

     Siemens AG 2000. All rights reserved.5-47SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) - 10.00 Edition5. Programming Preparatory FunctionsFeedrate programming, G93 to G975-48Exact stop, G9/G605-49Feedrate in continuous path mode, G64, G6415-50Programming the spindle motion5-51

  • Page 48

    5. Programming Preparatory Functions10.00.5-48 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) - 10.00 EditionFeedrate programming, G93 to G97ProgrammingN5 G90 G00 X... Y... Z... LFN10G94 F500 G01...M3 LFG93 FFeedrate in 1/min (inverse time feedrate...

  • Page 49

    10.00.5. Programming Preparatory Functions Siemens AG 2000. All rights reserved.5-49SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) - 10.00 EditionExact stop, G9/G60ProgrammingG601 Exact positioning fineG602 Exact positioning coarseG603 Exact positioning at end of interpolationG9Exact ...

  • Page 50

    5. Programming Preparatory Functions10.00.5-50 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) - 10.00 EditionFeedrate in continuous path mode, G64, G641ProgrammingG64 Continuous path modeG641 Block transition with contour transition rounding.The ro...

  • Page 51

    10.00.5. Programming Preparatory Functions Siemens AG 2000. All rights reserved.5-51SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) - 10.00 EditionProgramming the spindle motionProgrammingN05 SETMS(2) LFN10 G1 F300 X70 Y20 S270 M3 LFParametersS, SnSpindle speed in rpmM3, Mn=3 Clockwise...

  • Page 52

    5. Programming Preparatory Functions10.00.5-52 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) - 10.00 Edition

  • Page 53

     Siemens AG 2000. All rights reserved.6-53SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 Edition6. Subroutine Technique and CyclesSubroutine technique6-55The use of cycles6-57Explanation of parameters6-58Drilling, centering, CYCLE816-62Drilling, counterboring, CYCLE826-63Deep...

  • Page 54

    6-54 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionHole circle, HOLES26-73Elongated holes on a circle, LONGHOLE6-74Slots on a circle, SLOT16-75Circumferential slot, SLOT26-76Rectangular pocket milling, POCKET16-77Circular pocket mi...

  • Page 55

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-55SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionSubroutine techniqueProgrammingN40 G0 X500 Y500 Z500 LFN50 L230 P2 LFL...Subroutine callP...Number of repeats (max. 9999)Sub...

  • Page 56

    6. Subroutine Technique and Cycles10.006-56 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionSubroutine technique (cont.)ProgrammingN10 TRANS X0 Z150N20 L20N30 TRANS X0 Z140N40 L20N50 TRANS X0 Z130N60 L20L...Subroutine callXZMW1401301...

  • Page 57

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-57SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionThe use of cyclesPreconditionThe machining plane (G17, G18, G19) feed and speedmust be defined before calling the cycle.Cycl...

  • Page 58

    6. Subroutine Technique and Cycles: Drilling Cycles10.006-58 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionExplanation of parametersParameterExplanationAFSLAngle for slot length (enter without sign)ANG1Flank angle 1: at the side o...

  • Page 59

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-59SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionExplanation of parameters (cont.)ParameterExplanationFDISDistance of first hole from reference point (enter without sign)FDP...

  • Page 60

    6. Subroutine Technique and Cycles: Drilling Cycles10.006-60 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionExplanation of parameters (cont.)ParameterExplanationPO3Second intermediate pointPO4End point of thread in the longitudinal ...

  • Page 61

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-61SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionExplanation of parameters (cont.)ParameterExplanationVARIMachining modeSLOT1, SLOT2, POCKET1, POCKET2:0=complete machining1=...

  • Page 62

    6. Subroutine Technique and Cycles: Drilling Cycles10.006-62 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionDrilling, centering, CYCLE81SequenceThe "Drilling, centering" cycle produces a simple hole.ProgrammingCYCLE81 (RTP...

  • Page 63

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-63SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionDrilling, counterboring, CYCLE82SequenceThe "Drilling, counterboring" cycle produces a simple hole.When the final ...

  • Page 64

    6. Subroutine Technique and Cycles: Drilling Cycles10.006-64 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionDeep hole drilling, CYCLE83SequenceThe "Deep-hole drilling" cycle produces holes up to the finaldrilling depth by ...

  • Page 65

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-65SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionRigid tapping, CYCLE84SequenceCYCLE84 produces tapped holes without using a floatingtapholder.This cycle can be applied only...

  • Page 66

    6. Subroutine Technique and Cycles: Drilling Cycles10.006-66 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionTapping with floating tapholder, CYCLE840SequenceWith this cycle, tapped holes can be produced with floatingtapholder• wit...

  • Page 67

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-67SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionBore 1, CYCLE85SequenceIn the "Bore 1" cycle, the inward and outward motions areperformed at a feedrate that must ...

  • Page 68

    6. Subroutine Technique and Cycles: Drilling Cycles10.006-68 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionBore 2, CYCLE86SequenceIn the "Bore 2" cycle, an oriented spindle stop is performedon reaching the drilling depth....

  • Page 69

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-69SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionBore 3, CYCLE87SequenceIn the "Bore 3" cycle, a spindle stop without orientation iseffected on reaching the final ...

  • Page 70

    6. Subroutine Technique and Cycles: Drilling Cycles10.006-70 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionBore 4, CYCLE88SequenceIn the "Bore 4" cycle, a dwell time is effected on reachingthe final drilling depth togethe...

  • Page 71

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-71SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionBore 5, CYCLE89SequenceIn the "Bore 5" cycle, the inwards and the upwardsmovements are performed at the F value pr...

  • Page 72

    6. Subroutine Technique and Cycles: Drilling Cycles10.006-72 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionRow of holes, HOLES1SequenceWith this cycle, a row of holes can be produced on astraight line.ProgrammingHOLES1 (SPCA, SPCO,...

  • Page 73

    10.006. Subroutine Technique and Cycles: Drilling Cycles Siemens AG 2000. All rights reserved.6-73SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionHole circle, HOLES2SequenceWith this cycle, a hole circle can be machined.ProgrammingHOLES2 (CPA, CPO, RAD, STA1, INDA, NUM)...

  • Page 74

    6. Subroutine Technique and Cycles: Milling Cycles10.006-74 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionElongated holes on a circle, LONGHOLESequenceWith this cycle, elongated holes can be produced arrangedon a circle.The width o...

  • Page 75

    10.006. Subroutine Technique and Cycles: Milling Cycles Siemens AG 2000. All rights reserved.6-75SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionSlots on a circle, SLOT1SequenceWith this cycle, slots can be produced arranged on a circle.The longitudinal axis of the slot...

  • Page 76

    6. Subroutine Technique and Cycles: Milling Cycles10.006-76 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionCircumferential slot, SLOT2SequenceWith this cycle, circular slots can be produced arranged ona circle.The SLOT2 cycle is a c...

  • Page 77

    10.006. Subroutine Technique and Cycles: Milling Cycles Siemens AG 2000. All rights reserved.6-77SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionRectangular pocket milling, POCKET1SequenceWith this cycle, rectangular pockets can be produced in anylocation in the machini...

  • Page 78

    6. Subroutine Technique and Cycles: Milling Cycles10.006-78 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionCircular pocket milling, POCKET2SequenceWith this cycle, circular pockets can be produced.The cycle is a combined roughing/fi...

  • Page 79

    10.006. Subroutine Technique and Cycles: Milling Cycles Siemens AG 2000. All rights reserved.6-79SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionThread cutting, CYCLE90SequenceWith this cycle, internal and external threads can beproduced. The path in thread milling is b...

  • Page 80

    6. Subroutine Technique and Cycles: Turning Cycles10.006-80 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionRecessing cycle, CYCLE93SequenceThe recessing cycle allows symmetrical and asymmetricalrecesses to be produced for longitudin...

  • Page 81

    10.006. Subroutine Technique and Cycles: Turning Cycles Siemens AG 2000. All rights reserved.6-81SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionUndercut cycle, CYCLE94SequenceWith this cycle, undercuts to DIN 509 of forms E and F canbe produced with usual loading for a...

  • Page 82

    6. Subroutine Technique and Cycles: Turning Cycles10.006-82 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionStock removal cycle, CYCLE95SequenceWith the "Stock removal" cycle, a contour programmed in asubroutine can be pro...

  • Page 83

    10.006. Subroutine Technique and Cycles: Turning Cycles Siemens AG 2000. All rights reserved.6-83SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionThread undercut, CYCLE96SequenceWith this cycle, form A, B, C, D thread undercuts can beproduced in accordance with DIN 13 fo...

  • Page 84

    6. Subroutine Technique and Cycles: Turning Cycles10.006-84 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionThread cutting, CYCLE97SequenceWith the "Thread cutting" cycle, cylindrical and taperedoutside and inside threads c...

  • Page 85

    10.006. Subroutine Technique and Cycles: Turning Cycles Siemens AG 2000. All rights reserved.6-85SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 EditionChaining of threads, CYCLE98SequenceThis cycle allows production in longitudinal and facingoperations of several cylindrical ...

  • Page 86

    6. Subroutine Technique and Cycles: Turning Cycles10.006-86 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) –10.00 Edition

  • Page 87

     Siemens AG 2000. All rights reserved.7-87SINUMERIK 840D/810D/FM-NC Short Guide Programming (PAK) – 10.00 Edition7. Predefined Switching and Auxiliary FunctionsList of M commands7-88Forms7-89

  • Page 88

    7. Predefined Switching and Auxiliary Functions10.007-88 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PAK) – 10.00 EditionList of M commandsM0*Programmed stopM1*Optional stopM²*End of program (main program)M30*End of program as M2M17*End of subrout...

  • Page 89

    10.00 7. Predefined Switching and Auxiliary Functions Siemens AG 2000. All rights reserved.7-89SINUMERIK 840D/810D/FM-NC Short Guide Programming (PAK) – 10.00 EditionFormsYou can enter your own user-specific functions here.

  • Page 90

    7. Predefined Switching and Auxiliary Functions10.007-90 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PAK) – 10.00 EditionForms

  • Page 91

     Siemens AG 2000. All rights reserved.8-91SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 Edition8. Program KeyList of G functions8-92

  • Page 92

    8. Program Key10.008-92 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 1: Modal motion commandsNameNo.Meaningm/nDef.G01.Rapid traverse motionmG12.Linear interpolationmDef.G23.Circular interpolation clockwis...

  • Page 93

    8. Program Key10.00 Siemens AG 2000. All rights reserved.8-93SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 3: Write memoryNameNo.Meaningm/nDef.TRANS1.TRANSLATION: translation, programmablenROT2.ROTATION: rotation, programmablenSCALE3.SCALE: s...

  • Page 94

    8. Program Key10.008-94 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 7: Tool radius compensationNameNo.Meaningm/nDef.G401.No tool radius compensationmG412.Tool radius compensation left of contourmG423.Too...

  • Page 95

    8. Program Key10.00 Siemens AG 2000. All rights reserved.8-95SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 12: Block change criteria at exact stop (G60/G09)NameNo.Meaningm/nDef.G6011.Block change at exact stop finemDef.G6022.Block change at e...

  • Page 96

    8. Program Key10.008-96 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 17: Approach/retraction behavior, tool compensationNameNo.Meaningm/nDef.NORM1.Normal position at start/end pointmDef.KONT2.Travel aroun...

  • Page 97

    8. Program Key10.00 Siemens AG 2000. All rights reserved.8-97SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 22: Tool compensation typeNameNo.Meaningm/nDef.CUT2D1.2 1/2D tool compensationmDef.CUT2DF2.2 1/2D tool compensation relative to current...

  • Page 98

    8. Program Key10.008-98 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 27: Tool compensation on change of orientation at outside cornersNameNo.Meaningm/nDef.ORIC #1.Orientation changes are superimposed on t...

  • Page 99

    8. Program Key10.00 Siemens AG 2000. All rights reserved.8-99SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 32: OEM - G groupG820 #1.OEM G functionm/sDef.G821 #2.OEM G functionDef.G822 #3.OEM G functionG823 #4.OEM G functionG824 #5.OEM G funct...

  • Page 100

    8. Program Key10.008-100 Siemens AG 2000. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Programming (PGK) – 10.00 EditionList of G functionsGroup 35: Punching and nibblingNameNo.MeaningmDef.SPOF #1.Punching, nibbling offmDef.SON #2.Nibbling onmPON #3.Punching onmSONS #4.Nibbling ...

  • Page 101

    To:SIEMENS AGSuggestionsCorrectionsA&D MC BMSP. O. Box 3180D-91050 ErlangenFederal Republic of Germanyfor Publication/Manual:SINUMERIK 840D/840DiSINUMERIK 810D/FM-NCFax ++ 49 09131/98-1145)User DocumentationFromNameShort GuideProgrammingOrder No.:6FC5298-6AB30-0BP0Edition:10.00Company/departm...

x