Navigation

  • Page 1

    User's Guide 11/2002 EditionMeasuring CyclesSINUMERIK 840D/840Di/810D

  • Page 2

  • Page 3

    SINUMERIK 840D/840Di/810DMeasuring Cycles11.02 EditionUser's GuidePart 1: User's GuideIntroduction1Description of Parameters2Measuring Cycle AuxiliaryPrograms3Measuring in JOG4Measuring Cycles forMilling and MachiningCenters5Measuring Cycles forTurning Machines6Miscellaneous Functions7Part 2: Des...

  • Page 4

    0 Contents11.020SINUMERIK® DocumentationPrinting historyBrief details of this edition and previous editions are listed below.The status of each edition is shown by the code in the "Remarks" column.Status code in the "Remarks" column:A ....New documentation.B ....Unrevised edi...

  • Page 5

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0-50 11.02Contents0ContentsPart 1: User's GuideIntroduction1-151.1Basics............................................................................................................

  • Page 6

     Siemens AG, 2002. All rights reserved0-6SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0 Contents11.0202.3Description of the most important defining parameters...................................................2-582.3.1Measurement variant: _MVAR ..................

  • Page 7

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0-70 11.02Contents0Measuring Cycles for Milling and Machining Centers5-1035.1General preconditions .................................................................................

  • Page 8

     Siemens AG, 2002. All rights reserved0-8SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0 Contents11.0206.3.5Incremental measurement (SW 6.2 and higher) .....................................................6-2316.3.6Milling tool: suppression of starting angle po...

  • Page 9

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0-90 11.02Contents08.3.2Measuring in JOG ................................................................................................... 8-3098.4Function check ................

  • Page 10

     Siemens AG, 2002. All rights reserved0-10SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0 Preface11.02Structure of the manual0840 DNCU 571840 DNCU 572NCU 573810 D840 DiPrefaceOrganization of documentationThe SINUMERIK documentation is organized on 3 different l...

  • Page 11

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0-110 11.02PrefaceStructure of the manual0840 DNCU 571840 DNCU 572NCU 573810 D840 DiHotlinePlease address any questions to the following hotline:A&D Technical Support Phone:...

  • Page 12

     Siemens AG, 2002. All rights reserved0-12SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0 Preface11.02Use as intended0840 DNCU 571840 DNCU 572NCU 573810 D840 DiWarningsThe following warnings are used with graded severity.DangerIndicates an imminently hazardous ...

  • Page 13

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0-130 11.02PrefaceUse as intended0840 DNCU 571840 DNCU 572NCU 573810 D840 DiBasisYour SIEMENS SINUMERIK 840D, 804Di, 810D isstate of the art and is manufactured in accordancewit...

  • Page 14

     Siemens AG, 2002. All rights reserved0-14SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition0 Preface11.02Use as intended0840 DNCU 571840 DNCU 572NCU 573810 D840 DiServiceRepairs must only be carried out in accordance with theinformation given in the Service and Ma...

  • Page 15

    1 12.97Introduction1 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-15Introduction1.1Basics.............................................................................................................................. 1-161...

  • Page 16

    1 Introduction12.971.1 Basics1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-16SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1.1BasicsMeasuring cycles are general subroutines designed tosolve specific measurement tasks. They ca...

  • Page 17

    1 12.97Introduction1.2 General preconditions1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-171.2General preconditionsCertain preconditions need to be fulfilled beforemeasuring cycl...

  • Page 18

    1 Introduction12.971.2 General preconditions1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-18SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Programming• The inch/metric units system selected in themachine data for the basi...

  • Page 19

    1 12.97Introduction1.3 Plane definition1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-19 1.3Plane definition Tool radius compensation planes G17, G18 or G19 canbe selected. Leng...

  • Page 20

    1 Introduction12.971.4 Suitable probes1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-20SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 1.4Suitable probes Function In order to measure tool and workpiece dimensions, atouch-tri...

  • Page 21

    1 12.97Introduction1.4 Suitable probes1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-21 Multidirectional probe (3D) With this type, measuring cycles for workpiecemeasurement can...

  • Page 22

    1 Introduction12.971.5 Workpiece probe, calibration tool in TO memory1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-22SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition The probe must be mechanically aligned in the spindle insuc...

  • Page 23

    1 12.97Introduction1.5 Workpiece probe, calibration tool in TO memory1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-23 1.5.2 Workpiece probe, calibration tool in TO memory on turni...

  • Page 24

    1 Introduction12.971.5 Workpiece probe, calibration tool in TO memory1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-24SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Workpiece probe SL 7 Entry in TO memory P1500Tool typeP27To...

  • Page 25

    1 12.97Introduction1.6 Measuring principle1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-25 1.6Measuring principle Two inputs for the connection of touch trigger probesare provi...

  • Page 26

    1 Introduction12.971.6 Measuring principle1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-26SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Start position/setpoint position In the measuring procedure used, a position is specif...

  • Page 27

    1 12.97Introduction1.6 Measuring principle1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-27 Calculation of the deceleration path Since an optimal measurement speed can be set for...

  • Page 28

    1 Introduction12.971.7 Measuring strategy and compensation value calculation for tools1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-28SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 1.7Measuring strategy and compensation value...

  • Page 29

    1 12.97Introduction1.7 Measuring strategy and compensation value calculation for tools1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-29 Assuming the ideal case, only those dimensi...

  • Page 30

    1 Introduction12.971.7 Measuring strategy and compensation value calculation for tools1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-30SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Computational characteristic of the mean v...

  • Page 31

    1 12.97Introduction1.8 Parameters for checking the dim. deviation and compensation1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-31 1.8Parameters for checking the dim. deviation an...

  • Page 32

    1 Introduction12.971.8 Parameters for checking the dim. deviation and compensation1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-32SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition • For workpiece measurement with automatictoo...

  • Page 33

    1 12.97Introduction1.8 Parameters for checking the dim. deviation and compensation1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-33 • For workpiece measurement with zero offset ...

  • Page 34

    1 Introduction12.971.8 Parameters for checking the dim. deviation and compensation1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-34SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Safe area _TSA The safe area is active for all...

  • Page 35

    1 12.97Introduction1.8 Parameters for checking the dim. deviation and compensation1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-35 AUTOMATIC operation is interrupted when the to...

  • Page 36

    1 Introduction12.971.8 Parameters for checking the dim. deviation and compensation1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-36SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Bottom limit (zero compensation area) _TZL _TZ...

  • Page 37

    1 12.97Introduction1.9 Effect of empirical value, mean value and tolerance parameters1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-37 1.9Effect of empirical value, mean value and ...

  • Page 38

    1 Introduction12.971.10 Reference points on the machine and workpiece1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-38SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 1.10Reference points on the machine and workpiece Function...

  • Page 39

    1 12.97Introduction1.11 Measurement variants for milling machines & machining centers1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-39 1.11Measurement variants for milling mach...

  • Page 40

    1 Introduction12.971.11 Measurement variants for milling machines & machining centers1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-40SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 1.11.2 Measurement variants for fast meas...

  • Page 41

    1 12.97Introduction1.11 Measurement variants for milling machines & machining centers1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-41 Workpiece measurement, measuring the ho...

  • Page 42

    1 Introduction12.971.11 Measurement variants for milling machines & machining centers1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-42SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Workpiece measurement, measuring theou...

  • Page 43

    1 12.97Introduction1.11 Measurement variants for milling machines & machining centers1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-43 Two-point measurement at random angles ...

  • Page 44

    1 Introduction12.971.12 Measurement variants for lathes1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-44SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 1.12Measurement variants for lathes 1.12.1 Tool measurement for lathes T...

  • Page 45

    1 12.97Introduction1.12 Measurement variants for lathes1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-45 1.12.2 Workpiece measurement for turning machines: Single-point measurement...

  • Page 46

    1 Introduction12.971.12 Measurement variants for lathes1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-46SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Single-point measurement outside with 180°°°°reversal spindle Result:...

  • Page 47

    1 12.97Introduction1.12 Measurement variants for lathes1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-47 1.12.3 Workpiece measurement for turning machines: Two-point measurement ...

  • Page 48

    1 Introduction12.971.13 Measuring cycles interface1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-48SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 1.13Measuring cycles interface The measuring cycles provide an interactive f...

  • Page 49

    1 12.97Introduction1.13 Measuring cycles interface1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-49 Explanation The measuring cycles can display different measuringresult screens...

  • Page 50

    1 Introduction12.971.13 Measuring cycles interface1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-50SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 1.13.2 Setting parameters Function Values can be assigned to measuring cycle ...

  • Page 51

    1 12.97Introduction1.13 Measuring cycles interface1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition1-51 Explanation The sequence of the dialog for assigning parameters isas follows:...

  • Page 52

    1 Introduction12.971.13 Measuring cycles interface1840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved1-52SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 53

    2 12.97Description of Parameters2 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-53Description of Parameters2.1. Parameter concept for measuring cycles...........................................................................

  • Page 54

    2 Description of Parameters12.972.1. Parameter concept for measuring cycles2840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reserved2-54SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2.1.Parameter concept for measuring cyclesFunctionAs exp...

  • Page 55

    2 12.97Description of Parameters2.1. Parameter concept for measuring cycles 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-55 These blocks must be l...

  • Page 56

    2 Description of Parameters12.97 2.2 Parameter overview 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-56SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 2.2Parameter overview 2.2.1 Input parameters...

  • Page 57

    2 12.97Description of Parameters2.2 Parameter overview 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-57 Auxiliary parameters Parameters Type Val...

  • Page 58

    2 Description of Parameters12.97 2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-58SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 2.3Descri...

  • Page 59

    2 12.97Description of Parameters2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-59 CYCLE977...

  • Page 60

    2 Description of Parameters12.97 2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-60SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Measure...

  • Page 61

    2 12.97Description of Parameters2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-61 2.3.2 Numb...

  • Page 62

    2 Description of Parameters12.97 2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-62SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 2.3.3 Too...

  • Page 63

    2 12.97Description of Parameters2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-632.3.4 Offse...

  • Page 64

    2 Description of Parameters12.97 2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-64SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2. Specifi...

  • Page 65

    2 12.97Description of Parameters2.3 Description of the most important defining parameters2840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-652.3.5 Offset number _KNUM with flat D number st...

  • Page 66

    2 Description of Parameters12.97 2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-66SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2.3.6 Vari...

  • Page 67

    2 12.97Description of Parameters2.3 Description of the most important defining parameters2840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-672.3.8 Tolerance parameters: _TZL, _TMV, _T...

  • Page 68

    2 Description of Parameters12.97 2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-68SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2.3.9 Mult...

  • Page 69

    2 12.97Description of Parameters2.3 Description of the most important defining parameters2840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-692.3.10 Probe type/Probe number: _PRNUMFunc...

  • Page 70

    2 Description of Parameters12.97 2.3 Description of the most important defining parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-70SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 2.3.11 Em...

  • Page 71

    2 12.97Description of Parameters2.3 Description of the most important defining parameters2840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-71 2.3.12 Multiple measurement at the same ...

  • Page 72

    2 Description of Parameters12.97 2.4. Description of output parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-72SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 2.4.Description of output par...

  • Page 73

    2 12.97Description of Parameters2.4. Description of output parameters2840 DNCU 571840 DNCU 572NCU 573810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition2-73 2.4.2 Measuring cycle results in _OVI Function The field _...

  • Page 74

    2 Description of Parameters12.97 2.4. Description of output parameters 2 840 DNCU 571 840 DNCU 572NCU 573 810 D 840Di  Siemens AG, 2002. All rights reserved2-74SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 75

    3 12.97Measuring Cycle Auxiliary Programs3 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3-75Measuring Cycle Auxiliary Programs3.1Package structure of measuring cycles ...........................................................

  • Page 76

    3 Measuring Cycle Auxiliary Programs12.973.1 Package structure of measuring cycles3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reserved3-76SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3.1Package structure of measuring cyclesThe ...

  • Page 77

    3 12.97Measuring Cycle Auxiliary Programs3.2 Measuring cycle subroutines3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3-773.2Measuring cycle subroutinesFunctionThese measuring ...

  • Page 78

    3 Measuring Cycle Auxiliary Programs12.973.2 Measuring cycle subroutines3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reserved3-78SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3.2.1 CYCLE103: Parameter definition for measuring cyc...

  • Page 79

    3 12.97Measuring Cycle Auxiliary Programs3.2 Measuring cycle subroutines3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3-793.2.2 CYCLE116: Calculation of center point and radius...

  • Page 80

    3 Measuring Cycle Auxiliary Programs12.973.2 Measuring cycle subroutines3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reserved3-80SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionOutput dataThe results of the calculation are stored i...

  • Page 81

    3 12.97Measuring Cycle Auxiliary Programs3.3 Measuring cycle user programs3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3-813.3Measuring cycle user programsFunctionThese measur...

  • Page 82

    3 Measuring Cycle Auxiliary Programs12.973.3 Measuring cycle user programs3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reserved3-82SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3.3.2 CYCLE199: User program at the end of a measuri...

  • Page 83

    3 12.97Measuring Cycle Auxiliary Programs3.4 Subpackages3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3-833.4SubpackagesExplanationIn many application cases not all the measuri...

  • Page 84

    3 Measuring Cycle Auxiliary Programs12.973.4 Subpackages3840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840Di Siemens AG, 2002. All rights reserved3-84SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 85

    4 06.00Measuring in JOG4 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-85Measuring in JOG4.1General preconditions ............................................................................................... 4-864.2Workp...

  • Page 86

    4 Measuring in JOG06.004.1 General preconditions4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-86SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4.1General preconditionsCertain preconditions must be fulfilled beforemeasuring in JOG can be us...

  • Page 87

    4 06.00Measuring in JOG4.1 General preconditions4 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-87Availability of measuring cycles• The data blocks:GUD5.DEF andGUD6.DEFin directory DEFINE on diskette 1 have been loadedin...

  • Page 88

    4 Measuring in JOG06.004.1 General preconditions4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-88SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionMeasureworkpieceFor calculating and setting reference points.MeasuretoolFor measuring milling an...

  • Page 89

    4 06.00Measuring in JOG4.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-894.2Workpiece measurementFunctionWith this function you can set reference points onthe workpiece ...

  • Page 90

    4 Measuring in JOG06.004.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-90SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4.2.1 Operation and function sequence of workpiece measurementProcedure1. The workpiece is clamp...

  • Page 91

    4 06.00Measuring in JOG4.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-914.2.2 Measuring an edgeFunctionIf "Measure edge" is selected, a reference point can be...

  • Page 92

    4 Measuring in JOG06.004.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-92SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionOn "NC Start", the measuring operation is automaticallyperformed with a measuring feed...

  • Page 93

    4 06.00Measuring in JOG4.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-93Select the function with softkeyMeasureworkpiece CornerEnter details in input form• Select the...

  • Page 94

    4 Measuring in JOG06.004.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-94SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4.2.4 Measuring a holeFunctionWith "Hole", you can set the center of a hole as therefe...

  • Page 95

    4 06.00Measuring in JOG4.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-95Set the feedrate override switch to the samevalue as for calibration!Measurement is performed au...

  • Page 96

    4 Measuring in JOG06.004.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-96SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionEnter details in input form• Select the zero offset to which the specified setpointposition fo...

  • Page 97

    4 06.00Measuring in JOG4.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-97Calibrating the workpiece probe in any hole(radius)With this cycle, the probe can be calibrated ...

  • Page 98

    4 Measuring in JOG06.004.2 Workpiece measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-98SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionCalibrating a workpiece probe on anysurfaceWith this measuring cycle you can calibrate theprobe ...

  • Page 99

    4 06.00Measuring in JOG4.3 Tool measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-994.3Tool measurementFunctionTools can be measured in the machine with thisfunction.The tool lengths ar...

  • Page 100

    4 Measuring in JOG06.004.3 Tool measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-100SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4.3.2 Tool measurementFunctionIn tool measurement with a tool measuring probe (tableprobe system) ei...

  • Page 101

    4 06.00Measuring in JOG4.3 Tool measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition4-101Enter details in input form• Enter length offset V (positive value), required, forexample, for mil...

  • Page 102

    4 Measuring in JOG06.004.3 Tool measurement4840 DNCU 572NCU 573810D840Di Siemens AG, 2002. All rights reserved4-102SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionApproaching the tool measuring probeTraverse the calibration tool approximately to thecenter of the ...

  • Page 103

    5 12.97Measuring Cycles for Milling and Machining Centers5 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-103Measuring Cycles for Milling and Machining Centers5.1General preconditions ..........................................

  • Page 104

    5 Measuring Cycles for Milling and Machining Centers12.975.1 General preconditions5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D Siemens AG, 2002. All rights reserved5-104SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5.1General preconditionsFunctionMeasuring cycles...

  • Page 105

    5 12.97Measuring Cycles for Milling and Machining Centers5.1 General preconditions5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-105The two data blocks• GUD5...

  • Page 106

    5 Measuring Cycles for Milling and Machining Centers12.97 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reserved5-106SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition ...

  • Page 107

    5 12.97Measuring Cycles for Milling and Machining Centers 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-107 ...

  • Page 108

    5 Measuring Cycles for Milling and Machining Centers12.97 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reserved5-108SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition ...

  • Page 109

    5 12.97Measuring Cycles for Milling and Machining Centers 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-109 ...

  • Page 110

    5 Measuring Cycles for Milling and Machining Centers12.97 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reserved5-110SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition ...

  • Page 111

    5 12.97Measuring Cycles for Milling and Machining Centers 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-111 ...

  • Page 112

    5 Measuring Cycles for Milling and Machining Centers12.97 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reserved5-112SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition ...

  • Page 113

    5 12.97Measuring Cycles for Milling and Machining Centers 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-113 ...

  • Page 114

    5 Measuring Cycles for Milling and Machining Centers12.97 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reserved5-114SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 5....

  • Page 115

    5 12.97Measuring Cycles for Milling and Machining Centers 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-115 ...

  • Page 116

    5 Measuring Cycles for Milling and Machining Centers12.97 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reserved5-116SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionPar...

  • Page 117

    5 12.97Measuring Cycles for Milling and Machining Centers 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-117P...

  • Page 118

    5 Measuring Cycles for Milling and Machining Centers12.97 5.2 CYCLE971 Tool measuring for milling tools 5 840 DNCU 571 840 DNCU 572NCU 573 810 D  Siemens AG, 2002. All rights reserved5-118SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionPro...

  • Page 119

    5 12.97Measuring Cycles for Milling and Machining Centers5.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-1195.3CYCLE976 Calibrate workpie...

  • Page 120

    5 Measuring Cycles for Milling and Machining Centers12.975.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved5-120SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionResult parametersThe measurin...

  • Page 121

    5 12.97Measuring Cycles for Milling and Machining Centers5.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-121 Measurement variants The m...

  • Page 122

    5 Measuring Cycles for Milling and Machining Centers12.975.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved5-122SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 5.3.1 CYCLE976 Calibrate wor...

  • Page 123

    5 12.97Measuring Cycles for Milling and Machining Centers5.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-123 Procedure Position before ...

  • Page 124

    5 Measuring Cycles for Milling and Machining Centers12.975.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved5-124SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 5.3.2 CYCLE976 Calibrate wor...

  • Page 125

    5 12.97Measuring Cycles for Milling and Machining Centers5.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-125 Position after the cycle has...

  • Page 126

    5 Measuring Cycles for Milling and Machining Centers12.975.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved5-126SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 5.3.3 CYCLE976 Calibrate wor...

  • Page 127

    5 12.97Measuring Cycles for Milling and Machining Centers5.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-127 Procedure Position before ...

  • Page 128

    5 Measuring Cycles for Milling and Machining Centers12.975.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved5-128SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 5.3.4 Calibrate workpiece pr...

  • Page 129

    5 12.97Measuring Cycles for Milling and Machining Centers5.3 CYCLE976 Calibrate workpiece probe5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-129 Procedure Position before ...

  • Page 130

    5 Measuring Cycles for Milling and Machining Centers12.975.4 CYCLE977 Workpiece measurement:5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved5-130SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 5.4CYCLE977 Workpiece measureme...

  • Page 131

    5 12.97Measuring Cycles for Milling and Machining Centers5.4 CYCLE977 Workpiece measurement:5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-131 _OVR [28] REAL Safe area _O...

  • Page 132

    5 Measuring Cycles for Milling and Machining Centers12.975.4 CYCLE977 Workpiece measurement:5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved5-132SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition _OVI [0] INTEGER D number or ...

  • Page 133

    5 12.97Measuring Cycles for Milling and Machining Centers5.4 CYCLE977 Workpiece measurement:5840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-133 105 ZO calculation in rectang...

  • Page 134

    5 Measuring Cycles for Milling and Machining Centers12.97 5.4.1 CYCLE977 Measure hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-134SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles...

  • Page 135

    5 12.97Measuring Cycles for Milling and Machining Centers 5.4.1 CYCLE977 Measure hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM)...

  • Page 136

    5 Measuring Cycles for Milling and Machining Centers12.97 5.4.1 CYCLE977 Measure hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-136SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles...

  • Page 137

    5 12.97Measuring Cycles for Milling and Machining Centers 5.4.1 CYCLE977 Measure hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM)...

  • Page 138

    5 Measuring Cycles for Milling and Machining Centers12.97 5.4.1 CYCLE977 Measure hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-138SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles...

  • Page 139

    5 12.97Measuring Cycles for Milling and Machining Centers 5.4.1 CYCLE977 Measure hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM)...

  • Page 140

    5 Measuring Cycles for Milling and Machining Centers12.97 5.4.2 CYCLE977 ZO calculation in hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-140SINUMERIK 840D/840Di/810D User's Guide Measur...

  • Page 141

    5 12.97Measuring Cycles for Milling and Machining Centers 5.4.2 CYCLE977 ZO calculation in hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cy...

  • Page 142

    5 Measuring Cycles for Milling and Machining Centers12.97 5.4.2 CYCLE977 ZO calculation in hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-142SINUMERIK 840D/840Di/810D User's Guide Measur...

  • Page 143

    5 12.97Measuring Cycles for Milling and Machining Centers 5.4.2 CYCLE977 ZO calculation in hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cy...

  • Page 144

    5 Measuring Cycles for Milling and Machining Centers12.97 5.4.2 CYCLE977 ZO calculation in hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-144SINUMERIK 840D/840Di/810D User's Guide Measur...

  • Page 145

    5 12.97Measuring Cycles for Milling and Machining Centers 5.4.2 CYCLE977 ZO calculation in hole, shaft, groove, web, rectangle 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cy...

  • Page 146

    5 Measuring Cycles for Milling and Machining Centers12.97 5.5 CYCLE978 Workpiece measurement: Surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-146SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.0...

  • Page 147

    5 12.97Measuring Cycles for Milling and Machining Centers 5.5 CYCLE978 Workpiece measurement: Surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edit...

  • Page 148

    5 Measuring Cycles for Milling and Machining Centers12.97 5.5 CYCLE978 Workpiece measurement: Surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-148SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.0...

  • Page 149

    5 12.97Measuring Cycles for Milling and Machining Centers5.5.1 CYCLE978 ZO calculation on a surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Editio...

  • Page 150

    5 Measuring Cycles for Milling and Machining Centers12.97 5.5.1 CYCLE978 ZO calculation on a surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-150SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02...

  • Page 151

    5 12.97Measuring Cycles for Milling and Machining Centers5.5.1 CYCLE978 ZO calculation on a surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Editio...

  • Page 152

    5 Measuring Cycles for Milling and Machining Centers12.97 5.5 CYCLE978 Workpiece measurement: Surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-152SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.0...

  • Page 153

    5 12.97Measuring Cycles for Milling and Machining Centers 5.5 CYCLE978 Workpiece measurement: Surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edit...

  • Page 154

    5 Measuring Cycles for Milling and Machining Centers12.97 5.5 CYCLE978 Workpiece measurement: Surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-154SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.0...

  • Page 155

    5 12.97Measuring Cycles for Milling and Machining Centers 5.5 CYCLE978 Workpiece measurement: Surface 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edit...

  • Page 156

    5 Measuring Cycles for Milling and Machining Centers12.97 5.6 CYCLE979 Workpiece measurement: Hole/shaft/groove/web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-156SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles ...

  • Page 157

    5 12.97Measuring Cycles for Milling and Machining Centers 5.6 CYCLE979 Workpiece measurement: Hole/shaft/groove/web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) ...

  • Page 158

    5 Measuring Cycles for Milling and Machining Centers12.97 5.6 CYCLE979 Workpiece measurement: Hole/shaft/groove/web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-158SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles ...

  • Page 159

    5 12.97Measuring Cycles for Milling and Machining Centers 5.6.1 CYCLE979 Measure hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 ...

  • Page 160

    5 Measuring Cycles for Milling and Machining Centers12.97 5.6.1 CYCLE979 Measure hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-160SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – ...

  • Page 161

    5 12.97Measuring Cycles for Milling and Machining Centers 5.6.1 CYCLE979 Measure hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 ...

  • Page 162

    5 Measuring Cycles for Milling and Machining Centers12.97 5.6.1 CYCLE979 Measure hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-162SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – ...

  • Page 163

    5 12.97Measuring Cycles for Milling and Machining Centers 5.6.1 CYCLE979 Measure hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 ...

  • Page 164

    5 Measuring Cycles for Milling and Machining Centers12.97 5.6.2 CYCLE979 ZO calculation in hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-164SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles ...

  • Page 165

    5 12.97Measuring Cycles for Milling and Machining Centers 5.6.2 CYCLE979 ZO calculation in hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) ...

  • Page 166

    5 Measuring Cycles for Milling and Machining Centers12.97 5.6.2 CYCLE979 ZO calculation in hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-166SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles ...

  • Page 167

    5 12.97Measuring Cycles for Milling and Machining Centers 5.6.2 CYCLE979 ZO calculation in hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) ...

  • Page 168

    5 Measuring Cycles for Milling and Machining Centers12.97 5.6.2 CYCLE979 ZO calculation in hole, shaft, groove, web 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-168SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles ...

  • Page 169

    5 12.97Measuring Cycles for Milling and Machining Centers 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11....

  • Page 170

    5 Measuring Cycles for Milling and Machining Centers12.97 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-170SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) ...

  • Page 171

    5 12.97Measuring Cycles for Milling and Machining Centers 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11....

  • Page 172

    5 Measuring Cycles for Milling and Machining Centers12.97 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-172SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) ...

  • Page 173

    5 12.97Measuring Cycles for Milling and Machining Centers 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11....

  • Page 174

    5 Measuring Cycles for Milling and Machining Centers12.97 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-174SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) ...

  • Page 175

    5 12.97 Measuring Cycles for Milling and Machining Centers 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11...

  • Page 176

    5 Measuring Cycles for Milling and Machining Centers12.97 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-176SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) ...

  • Page 177

    5 12.97Measuring Cycles for Milling and Machining Centers 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11....

  • Page 178

    5 Measuring Cycles for Milling and Machining Centers12.97 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reserved5-178SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) ...

  • Page 179

    5 12.97Measuring Cycles for Milling and Machining Centers 5.7 CYCLE998 Angular measurement (ZO calculation) 5 840 DNCU 571 840 DNCU 572NCU 573 FM-NC 810 D 840 Di  Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11....

  • Page 180

    5 Measuring Cycles for Milling and Machining Centers12.975.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved5-180SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5.8CYCLE961 Automatic...

  • Page 181

    5 12.97Measuring Cycles for Milling and Machining Centers5.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-181Result parametersResu...

  • Page 182

    5 Measuring Cycles for Milling and Machining Centers12.975.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved5-182SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionParameters_MVAR105Set...

  • Page 183

    5 12.97Measuring Cycles for Milling and Machining Centers5.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-183_SETV[3]REALOffset of...

  • Page 184

    5 Measuring Cycles for Milling and Machining Centers12.975.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved5-184SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming exampleTh...

  • Page 185

    5 12.97Measuring Cycles for Milling and Machining Centers5.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-1855.8.2 Automatic setup...

  • Page 186

    5 Measuring Cycles for Milling and Machining Centers12.975.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved5-186SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionResult parametersResu...

  • Page 187

    5 12.97Measuring Cycles for Milling and Machining Centers5.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition5-187Parameters_MVAR117Set...

  • Page 188

    5 Measuring Cycles for Milling and Machining Centers12.975.8 CYCLE961 Automatic setup of inside and outside corner5840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved5-188SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming exampleTh...

  • Page 189

    6 12.97Measuring Cycles for Turning Machines6 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-189Measuring Cycles for Turning Machines6.1General preconditions ....................................................................

  • Page 190

    6 Measuring Cycles for Turning Machines12.976.1 General preconditions6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-190SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6.1General preconditionsFunctionMeasuring cycles are su...

  • Page 191

    6 12.97Measuring Cycles for Turning Machines6.1 General preconditions6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-191The two data blocks• GUD5.DEF• GUD6.DEF are also re...

  • Page 192

    6 Measuring Cycles for Turning Machines12.976.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-192SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6.2CYCLE972 Tool measurementProgrammingCYCLE972Func...

  • Page 193

    6 12.97Measuring Cycles for Turning Machines6.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-193Result parametersThe measuring cycle CYCLE972 retur...

  • Page 194

    6 Measuring Cycles for Turning Machines12.976.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-194SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6.2.1 CYCLE972 Calibrating the tool probeFunctionTh...

  • Page 195

    6 12.97Measuring Cycles for Turning Machines6.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-195Position after the cycle has terminatedOn completio...

  • Page 196

    6 Measuring Cycles for Turning Machines12.976.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-196SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming exampleCalibrating the tool probeThe to...

  • Page 197

    6 12.97Measuring Cycles for Turning Machines6.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-1976.2.2 CYCLE972 Determine dimensions of calibration ...

  • Page 198

    6 Measuring Cycles for Turning Machines12.976.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-198SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6.2.3 CYCLE972 Measure toolFunctionThe cycle calcul...

  • Page 199

    6 12.97Measuring Cycles for Turning Machines6.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-199Parameters_MVAR1Measurement variant: Tool measureme...

  • Page 200

    6 Measuring Cycles for Turning Machines12.976.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-200SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming exampleCalibrating the tool probe with ...

  • Page 201

    6 12.97Measuring Cycles for Turning Machines6.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-201; Measurement:N100 T3 D1Selection of the tool to be...

  • Page 202

    6 Measuring Cycles for Turning Machines12.976.2 CYCLE972 Tool measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-202SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionExplanationMeasure N100 to N200:The probe has been ...

  • Page 203

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-2036.3CYCLE982 Tool measurement (S...

  • Page 204

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-204SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition• Incremental calibration as ...

  • Page 205

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-205Result parametersThe measuring ...

  • Page 206

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-206SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Measurement variantsMeasurin...

  • Page 207

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-207• The following measurement v...

  • Page 208

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-208SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6.3.1 CYCLE982 Calibrate tool m...

  • Page 209

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-209Programming exampleCalibrating ...

  • Page 210

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-210SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6.3.2 CYCLE982 Measure tool Fun...

  • Page 211

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-211For mills/drills, setting data ...

  • Page 212

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-212SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionIn the case of milling tools, l...

  • Page 213

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-213Information about measuring wit...

  • Page 214

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-214SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionMeasurement variant Givengeomet...

  • Page 215

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-215Example:Radial position,R ≠ 0...

  • Page 216

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-216SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionMeasurement variant Givengeomet...

  • Page 217

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-217Measurement variant Givengeomet...

  • Page 218

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-218SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming exampleCalibrating ...

  • Page 219

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-219; Measurement:N100 T3 D1Selecti...

  • Page 220

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-220SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionExplanationMeasure N100 to N200...

  • Page 221

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-2216.3.3 CYCLE982 Automatic tool m...

  • Page 222

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-222SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionParameters_MVAR2 or ...02Measur...

  • Page 223

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-223Measurement variantGivengeometr...

  • Page 224

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-224SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionExample:Radial position,R ≠ 0...

  • Page 225

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-225Example:Radial position,R ≠ 0...

  • Page 226

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-226SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionExample: (as of SW5.4)Axial pos...

  • Page 227

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-227Example: (as ofSW 5.4)Radial po...

  • Page 228

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-228SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6.3.4 Incremental calibration (...

  • Page 229

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-229ProcedurePosition before the cy...

  • Page 230

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-230SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming exampleCalibrate to...

  • Page 231

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-2316.3.5 Incremental measurement (...

  • Page 232

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-232SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionParameters_MVAR1xxxx1(6 decimal...

  • Page 233

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-233If _CHBIT[20]=1, selected measu...

  • Page 234

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-234SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionExample:Axial position,miller, ...

  • Page 235

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-235Example:Radial position,miller,...

  • Page 236

    6 Measuring Cycles for Turning Machines12.976.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-236SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming exampleSXZrPProbeMS...

  • Page 237

    6 12.97Measuring Cycles for Turning Machines6.3 CYCLE982 Tool measurement (SW 5.3 and higher)6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-2376.3.6 Milling tool: suppression...

  • Page 238

    6 Measuring Cycles for Turning Machines12.976.4 CYCLE973 Calibrate workpiece probe6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-238SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 6.4CYCLE973 Calibrate workpiece probe ...

  • Page 239

    6 12.97Measuring Cycles for Turning Machines6.4 CYCLE973 Calibrate workpiece probe6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-239 Measurement variants The measuring cycl...

  • Page 240

    6 Measuring Cycles for Turning Machines12.976.4 CYCLE973 Calibrate workpiece probe6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-240SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 6.4.1 CYCLE973 Calibrate in the reference...

  • Page 241

    6 12.97Measuring Cycles for Turning Machines6.4 CYCLE973 Calibrate workpiece probe6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-241 Procedure Position before the cycle is ...

  • Page 242

    6 Measuring Cycles for Turning Machines12.976.4 CYCLE973 Calibrate workpiece probe6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-242SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 6.4.2 CYCLE973 Calibrate on a random surf...

  • Page 243

    6 12.97Measuring Cycles for Turning Machines6.4 CYCLE973 Calibrate workpiece probe6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-243 Procedure Position before the cycle is ...

  • Page 244

    6 Measuring Cycles for Turning Machines12.976.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-244SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 6.5CYCLE974 Workpiece measurement Programm...

  • Page 245

    6 12.97Measuring Cycles for Turning Machines6.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-245 _OVI [2] INTEGER Measuring cycle number _...

  • Page 246

    6 Measuring Cycles for Turning Machines12.976.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-246SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 6.5.1 CYCLE974 Single-point measurement ZO ca...

  • Page 247

    6 12.97Measuring Cycles for Turning Machines6.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-247 Parameters _MVAR 100 Measurement variant...

  • Page 248

    6 Measuring Cycles for Turning Machines12.976.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-248SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Procedure Position before the cycle is call...

  • Page 249

    6 12.97Measuring Cycles for Turning Machines6.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-249 6.5.2 CYCLE974 Single-point measurement Fu...

  • Page 250

    6 Measuring Cycles for Turning Machines12.976.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-250SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Parameters _MVAR 0 Measurement variant: ...

  • Page 251

    6 12.97Measuring Cycles for Turning Machines6.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-251Notice!Precise measurement is only possible wi...

  • Page 252

    6 Measuring Cycles for Turning Machines12.976.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-252SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Programming example Single-point measuremen...

  • Page 253

    6 12.97Measuring Cycles for Turning Machines6.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-253 6.5.3 CYCLE974 Single-point measurement with ...

  • Page 254

    6 Measuring Cycles for Turning Machines12.976.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-254SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Parameters _MVAR 1000 Measurement varian...

  • Page 255

    6 12.97Measuring Cycles for Turning Machines6.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-255Notice!Precise measurement is only possible wi...

  • Page 256

    6 Measuring Cycles for Turning Machines12.976.5 CYCLE974 Workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-256SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming exampleSingle-point measurement at...

  • Page 257

    6 12.97Measuring Cycles for Turning Machines6.6 CYCLE994 Two-point measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-2576.6CYCLE994 Two-point measurementProgrammingCY...

  • Page 258

    6 Measuring Cycles for Turning Machines12.976.6 CYCLE994 Two-point measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-258SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionExtension on measuring cycles SW 5.4 and highe...

  • Page 259

    6 12.97Measuring Cycles for Turning Machines6.6 CYCLE994 Two-point measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-259_OVI [2]INTEGERMeasuring cycle number_OVI [4]I...

  • Page 260

    6 Measuring Cycles for Turning Machines12.976.6 CYCLE994 Two-point measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-260SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProcedurePosition before the cycle is calledTh...

  • Page 261

    6 12.97Measuring Cycles for Turning Machines6.6 CYCLE994 Two-point measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-261Programming exampleTwo-point measurement, outs...

  • Page 262

    6 Measuring Cycles for Turning Machines12.976.7 Complex example for workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-262SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6.7Complex example for workpiece me...

  • Page 263

    6 12.97Measuring Cycles for Turning Machines6.7 Complex example for workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition6-263Programming exampleCalibrate workpi...

  • Page 264

    6 Measuring Cycles for Turning Machines12.976.7 Complex example for workpiece measurement6840 DNCU 571840 DNCU 572NCU 573FM-NC810 D840 Di Siemens AG, 2002. All rights reserved6-264SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 265

    7 05.98Miscellaneous Functions7 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-265Miscellaneous Functions7.1Logging of measuring results .........................................................................................

  • Page 266

    7 Miscellaneous Functions05.987.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-266SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7.1Logging of measuring resultsIn SW 4.3 and higher, the standard measuri...

  • Page 267

    7 05.98Miscellaneous Functions7.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-2677.1.2 Handling of log cyclesFunctionThe log is enabled and disabled via t...

  • Page 268

    7 Miscellaneous Functions05.987.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-268SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionCYCLE101Log OFFDisables the logging function and resets the internalflag....

  • Page 269

    7 05.98Miscellaneous Functions7.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-2697.1.3 Selecting the log contentsFunctionThe measurement result log contai...

  • Page 270

    7 Miscellaneous Functions05.987.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-270SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProcedureSpecification of the log contents is conducted via thevariable _...

  • Page 271

    7 05.98Miscellaneous Functions7.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-2717.1.4 Log formatProgrammingThe following values can be specified for the ...

  • Page 272

    7 Miscellaneous Functions05.987.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-272SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7.1.5 Log headerFunctionThe log header can be customized by the operatoro...

  • Page 273

    7 05.98Miscellaneous Functions7.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-273Line 1Date:98/09/15Time:10:05:30Page: 1Line 2Line 3Program: MEASPROGRAM_1...

  • Page 274

    7 Miscellaneous Functions05.987.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-274SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition_PROTFORM[6]INTEGER60_PROTFORM[0] = Number of lines per page80_PROTFORM[1...

  • Page 275

    7 05.98Miscellaneous Functions7.1 Logging of measuring results7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-275%_N_MEASPROGRAM_1_MPF;$PATH=/_N_MPF_DIR;Measure ring inside and outside w...

  • Page 276

    7 Miscellaneous Functions05.987.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-276SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7.2Cycle support for measuring cyclesFunctionIn SW 4.3 and higher, ...

  • Page 277

    7 05.98Miscellaneous Functions7.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-2777.2.1 Files for cycle supportFunctionMeasuring cycle support requir...

  • Page 278

    7 Miscellaneous Functions05.987.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-278SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7.2.3 Assignment of calls and measuring cyclesFunctionThe following...

  • Page 279

    7 05.98Miscellaneous Functions7.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-2797.2.4 Description of parameterization cyclesFunctionThe individual ...

  • Page 280

    7 Miscellaneous Functions05.987.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-280SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionCalibration in groove – CYCLE_973With CYCLE_973Soft keys Measurem...

  • Page 281

    7 05.98Miscellaneous Functions7.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-281Calibrating a tool measuring probe –CYCLE_CAL_TOOLSETTERWith CYCL...

  • Page 282

    7 Miscellaneous Functions05.987.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-282SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionMeasuring milling tools – CYCLE_971With CYCLE_971Soft keys Measur...

  • Page 283

    7 05.98Miscellaneous Functions7.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-283Measuring a shaft hole – CYCLE_977_979AWith CYCLE_977_979ASoft ke...

  • Page 284

    7 Miscellaneous Functions05.987.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-284SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionMeasure groove web – CYCLE_977_979BWith CYCLE_977_979BSoft keys M...

  • Page 285

    7 05.98Miscellaneous Functions7.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-285Parameters _MVAR INTEGERMeasurement variant _SETV[0] REALSetpoi...

  • Page 286

    7 Miscellaneous Functions05.987.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-286SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionAngle measurement – CYCLE_998With CYCLE_998Soft keys Measurem.mil...

  • Page 287

    7 05.98Miscellaneous Functions7.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-287 _SETV[4] REALSelection: Offset1...measured corner entered as zer...

  • Page 288

    7 Miscellaneous Functions05.987.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-288SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionSingle-point measurement – CYCLE_974With CYCLE_974Soft keys Measu...

  • Page 289

    7 05.98Miscellaneous Functions7.2 Cycle support for measuring cycles7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-289Setting additional parameters – CYCLE_PARAOn measuring cycles SW ...

  • Page 290

    7 Miscellaneous Functions05.987.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-290SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7.3Measuring cycle support in the program e...

  • Page 291

    7 05.98Miscellaneous Functions7.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-2917.3.2 New functions of the input formsFunct...

  • Page 292

    7 Miscellaneous Functions05.987.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-292SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionVertical soft key menu for turning technolo...

  • Page 293

    7 05.98Miscellaneous Functions7.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-293Vertical soft key menu for milling technolo...

  • Page 294

    7 Miscellaneous Functions05.987.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-294SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionVertical soft key menu for workpiecemeasure...

  • Page 295

    7 05.98Miscellaneous Functions7.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-295Vertical advancement menu for workpiecemeas...

  • Page 296

    7 Miscellaneous Functions05.987.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-296SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionProgramming example(generated with measurin...

  • Page 297

    7 05.98Miscellaneous Functions7.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-2977.3.3 GUD variables for adaptation of measu...

  • Page 298

    7 Miscellaneous Functions05.987.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-298SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition _MZ_MASK[2] 0 Forms without input fields...

  • Page 299

    7 05.98Miscellaneous Functions7.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition7-299 _MZ_MASK[6] 0 The generated NC code does...

  • Page 300

    7 Miscellaneous Functions05.987.3 Measuring cycle support in the program editor (≥ SW 6.2)7840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved7-300SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 301

    8 12.97Hardware, Software and Installation8 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8-301Part 2: Description of FunctionsHardware, Software and Installation8.1Overview .....................................................

  • Page 302

    8 Hardware, Software and Installation12.978.1 Overview8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved8-302SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8.1OverviewFunctionYou can use measuring cycles for automaticmeasuring on CNC mac...

  • Page 303

    8 12.97Hardware, Software and Installation8.2 Hardware requirements8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8-3038.2Hardware requirements8.2.1 General hardware requirementsAxis assi...

  • Page 304

    8 Hardware, Software and Installation12.978.2 Hardware requirements8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved8-304SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionInterfaces, operator and display elements on the NCU moduleCF+5VNFCB...

  • Page 305

    8 12.97Hardware, Software and Installation8.2 Hardware requirements8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8-305ExplanationInterface• I/O interface37-pin subminiature D connector...

  • Page 306

    8 Hardware, Software and Installation12.978.2 Hardware requirements8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved8-306SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Connection to FM-NC NCU 570.2 The following figure shows the FM-N...

  • Page 307

    8 12.97Hardware, Software and Installation8.2 Hardware requirements8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8-307 Explanation Interface• I/O interface- 20-way front connector (X...

  • Page 308

    8 Hardware, Software and Installation12.978.3 Software requirements8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved8-308SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8.3Software requirementsExplanationHow the measuring cycles are supp...

  • Page 309

    8 12.97Hardware, Software and Installation8.3 Software requirements8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8-3098.3.2 Measuring in JOGExplanationOptions"Measurement in JOG&quo...

  • Page 310

    8 Hardware, Software and Installation12.978.4 Function check8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved8-310SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8.4Function checkFunctionMeasurement commandThe control has the command MEA...

  • Page 311

    8 12.97Hardware, Software and Installation8.4 Function check8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8-311Example of functional check%_N_CHECK_PROBE_MPF;$PATH=/_N_MPF_DIR;Test progr...

  • Page 312

    8 Hardware, Software and Installation12.978.5 Start-up sequences8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved8-312SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8.5Start-up sequences8.5.1 Start-up flowchart for measuring cycles and ...

  • Page 313

    8 12.97Hardware, Software and Installation8.5 Start-up sequences8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8-313No12NC STARTIs measuring blockwith MEAS present ?Execute NC blockYesYes...

  • Page 314

    8 Hardware, Software and Installation12.978.5 Start-up sequences8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved8-314SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition3YesNoEndNC STARTNoYesInform service personnel2Does bit change from &qu...

  • Page 315

    8 12.97Hardware, Software and Installation8.5 Start-up sequences8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition8-3158.5.2 Starting up the measuring cycle interface for the MMC 102Function...

  • Page 316

    8 Hardware, Software and Installation12.978.5 Start-up sequences8840 DNCU 571840 DNCU 572NCU 573810 D Siemens AG, 2002. All rights reserved8-316SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 317

    9 12.97Supplementary Conditions9840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition9-317Supplementary ConditionsThere are no special conditions for the measuringcycles. However, the foll...

  • Page 318

    9 Supplementary Conditions12.979840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved9-318SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 319

    10 12.97Data Description10 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-319Data Description10.1 Machine data for machine cycle runs.......................................................................... 10-32010.2 Cyc...

  • Page 320

    10 Data Description12.9710.1 Machine data for machine cycle runs10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-320SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10.1Machine data for machine cycle runsFunctionMemory-configuri...

  • Page 321

    10 12.97Data Description10.1 Machine data for machine cycle runs10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-32118170MM_NUM_MAX_FUNC_NAMESMD numberNumber of special functions ...

  • Page 322

    10 Data Description12.9710.1 Machine data for machine cycle runs10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-322SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionFunctionMachine data for adapting the probe13200MEAS_PROBE_LOW_...

  • Page 323

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-32310.2Cycle data10.2.1 Data concept for measuring cyclesFunctionMeasuring cycles are gener...

  • Page 324

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-324SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition The value for the defining parameters of the measuringcycles in module GUD5.DEF can b...

  • Page 325

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-325 Excerpt from GUD5.DEF For adapting the GUD5.DEF module, only thefollowing section is ...

  • Page 326

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-326SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition N50 DEF CHAN BOOL _CHBIT[20]=(0,1,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0) N60 DEF NCK ST...

  • Page 327

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-327• Software status of the control – SW 5• Channel-oriented values (N40)- 20 memorie...

  • Page 328

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-328SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 10.2.3 Central values _CVAL Number of elements min. input value: - max. input...

  • Page 329

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-329 Tool probe on milling machine ZTrigger point in +Z_TP[x,5]Trigger point in -Z_TP[x...

  • Page 330

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-330SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition _WP Workpiece probe min. input value: - max. input value: - Changes valid af...

  • Page 331

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-331 _KB Calibration block min. input value: - max. input value: - Changes valid ...

  • Page 332

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-332SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition _CM[] Monitoring for tool measurement with rotating spindle, only effective with ...

  • Page 333

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-333 10.2.4 Central bits _CBIT Central bits min. input value: 0 max. input value: ...

  • Page 334

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-334SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition M0 with measurement repetition If _CBIT[1] is set, and the parameter limits fordimens...

  • Page 335

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-335 Mono probe position offset If _CBIT[8] is set, the probe position is offset by theval...

  • Page 336

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-336SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition 10.2.5 Central strings _SI Central strings min. input value: - max. input val...

  • Page 337

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-337 10.2.6 Channel-oriented values _EVMVNUM Number of empirical values and mean valu...

  • Page 338

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-338SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Rapid traverse speed The intermediate positions calculated by themeasuring cycles are...

  • Page 339

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-339 10.2.7 Channel-oriented bits _CHBIT Channel bits min. input value: - max. inp...

  • Page 340

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-340SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Measurement input tool measurement _CHBIT[1]=0: Measuring input 1 is activated for to...

  • Page 341

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-341 Tool offset mode for workpiece measurement withautomatic tool offset _CHBIT[6]=0: The...

  • Page 342

    10 Data Description12.9710.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-342SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition Link between spindle position and coordinate rotation _CHBIT[13]=0: If multiprobes ar...

  • Page 343

    10 12.97Data Description10.2 Cycle data10840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-343_CHBIT[16]=1: The return velocity is always carried out at therapid traverse percentage ...

  • Page 344

    10 Data Description12.9710.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-344SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10.3Data for measuring in JOG10.3.1 Machine data for ensuring ability to function1160...

  • Page 345

    10 12.97Data Description10.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-34520310TOOL_MANAGEMENT_MASKMD numberChannel-specific activation of tool managementDefau...

  • Page 346

    10 Data Description12.9710.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-346SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10.3.2 Modifying the GUD7 data blockFunctionNoticeThe GUD7 data block does not have t...

  • Page 347

    10 12.97Data Description10.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-347Example:A milling machine has a tool measuring probe. Toolmeasurement is only perform...

  • Page 348

    10 Data Description12.9710.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-348SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionE_MESS_D_R=1Measuring path for radius measurement[mm] for tool measurement(in front o...

  • Page 349

    10 12.97Data Description10.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-34910.3.3 Settings in data block GUD6FunctionThe channel specific data fields _JM_I[ ], ...

  • Page 350

    10 Data Description12.9710.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-350SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition __JM_B Bool value field for JOG measurement min. input value: - max. input ...

  • Page 351

    10 12.97Data Description10.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition10-35110.3.4 Loading files for measuring in JOGFunctionThe files located on diskette 2 in d...

  • Page 352

    10 Data Description12.9710.3 Data for measuring in JOG10840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved10-352SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 353

    11 12.97Examples11 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition11-353Examples11.1 Determining the repeat accuracy ................................................................................ 11-35411.2 Adapting the dat...

  • Page 354

    11 Examples12.9711.1 Determining the repeat accuracy11840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved11-354SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition11.1Determining the repeat accuracyFunctionTest programThe program is used ...

  • Page 355

    11 12.97Examples11.2 Adapting the data for a particular machine11840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition11-355After selecting the parameter display (user-definedvariables), t...

  • Page 356

    11 Examples12.9711.2 Adapting the data for a particular machine11840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved11-356SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition N13 DEF NCK REAL _KB[3,7]1) N14 DEF NCK REAL _CM[8]=(60,20...

  • Page 357

    11 12.97Examples11.2 Adapting the data for a particular machine11840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition11-357 Explanation 2. Adapting specific values Value adaptation is a...

  • Page 358

    11 Examples12.9711.2 Adapting the data for a particular machine11840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved11-358SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 359

    12 12.97Data Fields, Lists12 Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition12-359Data Fields, Lists12.1 Machine data...............................................................................................................

  • Page 360

    12 Data Fields, Lists12.9712.1 Machine data12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved12-360SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition12.1Machine dataNumberIdentifierNameReferenceGeneral ($MN_...)10132MMC_CMD_TIMEOUTMo...

  • Page 361

    12 12.97Data Fields, Lists12.3 Alarms12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition12-36112.3AlarmsGeneral notesIf faulty states are detected in the measuring cycles,an alarm is g...

  • Page 362

    12 Data Fields, Lists12.9712.3 Alarms12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved12-362SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionOverview of the measuring cycle alarmsThe following table displays the errors which occur ...

  • Page 363

    12 12.97Data Fields, Lists12.3 Alarms12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition12-363Alarm numberAlarm textSourceMeaning, remedy61315"Check tool edge position"CYCLE9...

  • Page 364

    12 Data Fields, Lists12.9712.3 Alarms12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved12-364SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionAlarm numberAlarm textSourceMeaning, remedy61328"Check D number"AllThe D number ...

  • Page 365

    12 12.97Data Fields, Lists12.3 Alarms12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition12-365Alarm numberAlarm textSourceMeaning, remedy61343"Tool for specified toolidentifier do...

  • Page 366

    12 Data Fields, Lists12.9712.3 Alarms12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved12-366SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionAlarm numberAlarm textSourceMeaning, remedy61360"Undefined logging job -press RESET t...

  • Page 367

    12 12.97Data Fields, Lists12.3 Alarms12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 Edition12-367Alarm numberAlarm textSourceMeaning, remedy61402"Probe collision, travellimitation th...

  • Page 368

    12 Data Fields, Lists12.9712.3 Alarms12840 DNCU 571840 DNCU 572NCU 573810 D840 Di Siemens AG, 2002. All rights reserved12-368SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionNotes

  • Page 369

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-369A 11.02AppendixAAppendixA Overview of measuring cycle parameters.........................................................................A-371B Abbreviations .................

  • Page 370

     Siemens AG, 2002. All rights reservedA-370SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02A

  • Page 371

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-371A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiAOverview of measuring cycle parametersParameter definitionParameters must b...

  • Page 372

     Siemens AG, 2002. All rights reservedA-372SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 961Workpiece measurementAutomatic setup inside and outside cornerfor G...

  • Page 373

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-373A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 961Workpiece measurementAutomatic setup inside and outside cornerfor G...

  • Page 374

     Siemens AG, 2002. All rights reservedA-374SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 971Tool measurement of milling tools on milling machinesPossible axesa...

  • Page 375

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-375A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 971Tool measurement of milling tools on milling machinesPossible axesa...

  • Page 376

     Siemens AG, 2002. All rights reservedA-376SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 972Tool measurement of turning tools with cutting edge 1 – 8 on turn...

  • Page 377

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-377A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 973Workpiece measurementPossible axes abscissa/ordinatefor G17: X=1 Y=...

  • Page 378

     Siemens AG, 2002. All rights reservedA-378SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 973Workpiece measurementPossible axes abscissa/ordinatefor G17: X=1 Y=...

  • Page 379

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-379A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 974Workpiece measurementCYCLE 994Possible measuring axes abscissa/ordi...

  • Page 380

     Siemens AG, 2002. All rights reservedA-380SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 974Workpiece measurementCYCLE 994Possible measuring axes abscissa/ordi...

  • Page 381

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-381A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 976Workpiece measurementPossible measuring axes abscissa/ordinatefor G...

  • Page 382

     Siemens AG, 2002. All rights reservedA-382SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 976Workpiece measurementPossible measuring axes abscissa/ ordinatefor ...

  • Page 383

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-383A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 977Workpiece measurementPossible measuring axes abscissa/ordinatefor G...

  • Page 384

     Siemens AG, 2002. All rights reservedA-384SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 977Workpiece measurementPossible measuring axes abscissa/ ordinatefor ...

  • Page 385

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-385A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 978Workpiece measurementCYCLE 998Possible measuring axes abscissa/ordi...

  • Page 386

     Siemens AG, 2002. All rights reservedA-386SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 978Workpiece measurementCYCLE 998Possible measuring axes abscissa/ordi...

  • Page 387

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-387A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 979Workpiece measurementPossible measurementsG17: X -Y planeG18: Z -X ...

  • Page 388

     Siemens AG, 2002. All rights reservedA-388SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 979Workpiece measurementPossible measurementsG17: X -Y planeG18: Z -X ...

  • Page 389

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-389A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 982Tool measurement of turning, drilling, and milling tools for turnin...

  • Page 390

     Siemens AG, 2002. All rights reservedA-390SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE 982Tool measurement of turning, drilling, and milling tools for turnin...

  • Page 391

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-391A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiResult parameters calibrationCYCLE971CYCLE972CYCLE973CYCLE976GUD5_OVR [0]REA...

  • Page 392

     Siemens AG, 2002. All rights reservedA-392SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiResult parameters measurement (turning machines)CYCLE974CYCLE994CYCLE972GUD5...

  • Page 393

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-393A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiFor measurement with automatic tool offset onlyResult parameters measurement...

  • Page 394

     Siemens AG, 2002. All rights reservedA-394SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 Di_OVR [24]REAL_OVR[25]REALa_OVR[26]REAL_OVR [27]REALZero offset area_OVR [28]...

  • Page 395

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-395A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiNC machine dataMD number IdentifierDescriptionMax.input valueDefaultvalueVal...

  • Page 396

     Siemens AG, 2002. All rights reservedA-396SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCycle machine data for measuring in JOGThe measuring cycle data for measurem...

  • Page 397

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-397A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCentral valuesModuleIdentifierDescriptionMax.input valueDefaultvalueValue fo...

  • Page 398

     Siemens AG, 2002. All rights reservedA-398SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCentral valuesModuleIdentifierDescriptionMax.input valueDefaultvalueValue fo...

  • Page 399

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-399A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCentral bitsModuleIdentifierDescriptionMax.input valueDefaultvalueValue form...

  • Page 400

     Siemens AG, 2002. All rights reservedA-400SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiChannel-oriented valuesModuleIdentifierDescriptionMax.input valueDefaultvalu...

  • Page 401

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-401A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiChannel-specific values (for measurement in JOG)ModuleIdentifierDescriptionM...

  • Page 402

     Siemens AG, 2002. All rights reservedA-402SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiGUD 6_CHBIT[10]Display of measurement result screen0GUD 6_CHBIT[11]Acknowled...

  • Page 403

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-403A 11.02AppendixOverview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiResult parameters measurementCYCLE974 CYCLE977 CYCLE978 CYCLE979 CYCLE994 CY...

  • Page 404

     Siemens AG, 2002. All rights reservedA-404SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02Overview of measuring cycle parametersA840 DNCU 571840 DNCU 572NCU 573810 D840 Di_OVI [0]INTEGER D # / ZO #_OVI[1]INTEGER_OVI [2]INTEGER Measuring cycle numb...

  • Page 405

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-405A 11.02AppendixAbbreviationsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiBAbbreviationsCNCComputerized Numerical ControlCPUCentral Processing UnitDINDeutsche Industrie Norm (...

  • Page 406

     Siemens AG, 2002. All rights reservedA-406SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02AbbreviationsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiSRSubroutineSWSoftware (version)TOTool OffsetTOATool Offset Active: Identification (file type) for to...

  • Page 407

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-407A 11.02AppendixTermsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCTermsImportant terms are listed below in alphabetical order. Cross-referencesto other entries in this glossa...

  • Page 408

     Siemens AG, 2002. All rights reservedA-408SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02TermsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiDData modules formeasuring cyclesData modules GUD5.DEF and GUD6.DEF contain data required forconfiguration an...

  • Page 409

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-409A 11.02AppendixTermsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiG...JInprocessmeasurementThis method processes the probe signal directly in the NC.KLLogging ofmeasurement re...

  • Page 410

     Siemens AG, 2002. All rights reservedA-410SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02TermsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiMeasurement accuracyThe measurement accuracy which can be obtained is thusdependent on the following factors:...

  • Page 411

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-411A 11.02AppendixTermsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiNOOffset angle positionIf a -> monoprobe is used, the position of the probe can also becorrected for machi...

  • Page 412

     Siemens AG, 2002. All rights reservedA-412SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02TermsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiSSafe areaThe safe area _TSA does not affect the offset value; it is used fordiagnosis.If this limit is reach...

  • Page 413

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-413A 11.02AppendixTermsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiWWeighting factor formean value derivationThe weighting factor k can be applied to allow different weighting ...

  • Page 414

     Siemens AG, 2002. All rights reservedA-414SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02TermsA840 DNCU 571840 DNCU 572NCU 573810 D840 DiNotes

  • Page 415

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-415A 11.02AppendixReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 DiDReferencesGeneral Documentation/BU/SINUMERIK 840D/840Di/810D/802S, C, DOrdering InformationCatalog NC 6...

  • Page 416

     Siemens AG, 2002. All rights reservedA-416SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02ReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/AUK/SINUMERIK 840D/810DAutoTurn Short Operating Guide(09.01 Edition)Order No.: 6FC5 298-4AA30-0BP3/AUP/...

  • Page 417

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-417A 11.02AppendixReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/BAS/SINUMERIK 840D/810DOperator's Guide ShopMill(09.02 Edition)Order No.: 6FC5 298-6AD10-0BP1/BAT/SINUM...

  • Page 418

     Siemens AG, 2002. All rights reservedA-418SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02ReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/PGT/SINUMERIK 840D/840Di/810DProgramming Guide ISO Turning(11.02 Edition)Order No.: 6FC5 298-6AC10-0BP2...

  • Page 419

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-419A 11.02AppendixReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/BH/SINUMERIK 840D/840Di/810DOperator Components Manual (Hardware)(11.02 Edition)Order No.: 6FC5 297-6AA...

  • Page 420

     Siemens AG, 2002. All rights reservedA-420SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02ReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Dic) Software/FB1/SINUMERIK 840D/840Di/810DDescription of Functions, Basic Machine (Part 1)(11.02 Edition)...

  • Page 421

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-421A 11.02AppendixReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/FB2/SINUMERIK 840D/840Di/810D(CCU2)Description of Functions, Extended Functions (Part 2) (11.02 Edition...

  • Page 422

     Siemens AG, 2002. All rights reservedA-422SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02ReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/FBA/SIMODRIVE 611D/SINUMERIK 840D/810DDescription of Functions, Drive Functions(11.02 Edition)(the vari...

  • Page 423

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-423A 11.02AppendixReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/FBDN/CAM Integration DNC NT-2000Description of Functions(01.02 Edition)System for NC Data Management an...

  • Page 424

     Siemens AG, 2002. All rights reservedA-424SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02ReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/FBO/SINUMERIK 840D/810DDescription of FunctionsConfiguring OP 030 Operator Interface(09.01 Edition)(the...

  • Page 425

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-425A 11.02AppendixReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/FBTC/SINUMERIK 840D/810DIT SolutionsSINUMERIK Tool Data Communication SinTDC(01.02 Edition)Description ...

  • Page 426

     Siemens AG, 2002. All rights reservedA-426SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02ReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/PJE/SINUMERIK 840D/810DConfiguring Package HMI Embedded(08.01 Edition)Description of Functions: Softwar...

  • Page 427

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-427A 11.02AppendixReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/POS3/SIMODRIVE POSMO SI/CD/CADistributed Servo Drive Systems, User's Guide(08.02 Edition)Order No.: 6SN...

  • Page 428

     Siemens AG, 2002. All rights reservedA-428SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02ReferencesA840 DNCU 571840 DNCU 572NCU 573810 D840 Di/SP/SIMODRIVE 611-A/611-DSimoPro 3.1Program for Configuring Machine-Tool DrivesOrder No.: 6SC6 111-6PC00...

  • Page 429

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-429A 11.02AppendixIndexA840 DNCU 571840 DNCU 572NCU 573810 D840 DiEIndex22-point measurement at random angles 1-43AAdapting the data for a particular machine 11-355Alarms 1...

  • Page 430

     Siemens AG, 2002. All rights reservedA-430SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02IndexA840 DNCU 571840 DNCU 572NCU 573810 D840 DiCYCLE_CAL_PROBE 7-280CYCLE_CAL_TOOLSETTER 7-281CYCLE_PARA 7-289CYCLE103 3-78CYCLE116 3-79CYCLE198 3-81C...

  • Page 431

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-431A 11.02AppendixIndexA840 DNCU 571840 DNCU 572NCU 573810 D840 DiMeasurement path multiplication 2-68Measurement variants 1-39, 1-44, 2-58Measuring a shaft hole – CYCLE_9...

  • Page 432

     Siemens AG, 2002. All rights reservedA-432SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02IndexA840 DNCU 571840 DNCU 572NCU 573810 D840 DiSetting additional parameters – CYCLE_PARA7-289Single-point measurement – CYCLE_978 7-285Single-point me...

  • Page 433

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-433A 11.02AppendixIndexA840 DNCU 571840 DNCU 572NCU 573810 D840 DiZO calculation in a grooveCYCLE977 5-140CYCLE979 5-164ZO calculation in a holeCYCLE977 5-140CYCLE979 5-16...

  • Page 434

     Siemens AG, 2002. All rights reservedA-434SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02IdentifiersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiFIdentifiersList of input/output variables of the measuring cyclesNameStands forExplanation_CALNUMCalib...

  • Page 435

     Siemens AG, 2002. All rights reservedSINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA-435A 11.02AppendixIdentifiersA840 DNCU 571840 DNCU 572NCU 573810 D840 Di_PROTFORM[6]Log formatting_PROTNAME[2]Name of log file_PROTSYM[2]Separator in the log_PROTVAL[11]Log he...

  • Page 436

     Siemens AG, 2002. All rights reservedA-436SINUMERIK 840D/840Di/810D User's Guide Measuring Cycles (BNM) – 11.02 EditionA Appendix11.02IdentifiersA840 DNCU 571840 DNCU 572NCU 573810 D840 DiNotes

  • Page 437

    ToSIEMENS AGSuggestionsCorrectionsA&D MC BMSP.O. Box 3180D-91050 Erlangen, GermanyPhone: ++49-(0)180-5050-222 [Hotline]Fax: ++49-(0)9131-98-2176 [Documentation]Email: motioncontrol.docu@erlf.siemens.deFor Publication/Manual:SINUMERIK 840D/840Di/810DMeasuring Cycles User DocumentationFrom:Name...

  • Page 438

    User DocumentationSINUMERIK840D/810DSINUMERIKOverview of SINUMERIK 840D/840Di/810D Documentation (11.2002)BrochureCatalog Ordering Info.NC 60 *)Description of Functions Drive Functions *)Description of Functions– Basic Machine *) – Extended Functions– Special Functions611D840D/810DSINUMERIK...

  • Page 439

    © Siemens AG, 2002Subject to change without prior notice Order No.: 6FC5298-6AA70-0BP2Printed in GermanySiemens AGAutomation & DrivesMotion Control SystemsP.O. Box 3180, D-91050 ErlangenGermanywww.ad.siemens.de

x