Navigation

  • Page 1

    Restrictions 1 SINUMERIK 840D Virtual NCK for Simulation Restrictions Description of functions Valid for Control Softwareversion SINUMERIK 840D 7 VNCK 1.4 07/2005 Edition

  • Page 2

    SINUMERIK®-Docmentation Trademarks SIMATIC®, SIMATIC HMI®, SIMATIC NET®, SIROTEC®, SINUMERIK®, and SIMODRIVE® are registered trademarks of Siemens AG. The other designations in this publication may also be trademarks, the use of which by third parties may constitute copyright violation....

  • Page 3

    07/2005 Contents © Siemens AG 2005 All Rights Reserved SINUMERIK 840D VNCK Restrictions (FBVNCK) - 07/2005 Edition iii Contents 1 Restrictions ..................................................................................... 5,1-5 5, 1.1 General restrictions..................................

  • Page 4

    Contents 07/2005 © Siemens AG 2005 All Rights Reserved iv SINUMERIK 840D VNCK Restrictions (FBVNCK) - 07/2005 Edition

  • Page 5

    07/2005 1 Restrictions 1.1 General restrictions © Siemens AG 2005 All Rights Reserved SINUMERIK 840D VNCK Restrictions (FBVNCK) - 07/2005 Edition 1-5 1 Restrictions 1.1 General restrictions VNCK Version 1.4.0.0 was generated on the basis of a Sinumerik 840D software release Version 7.1. P...

  • Page 6

    1 Restrictions 07/2005 1.4 Restrictions due to missing drive functionality and sensor feedback on the machine tool © Siemens AG 2005 All Rights Reserved 1-6 SINUMERIK 840D VNCK Restrictions (FBVNCK) - 07/2005 Edition 1.4 Restrictions due to missing drive functionality and sensor feedback on...

  • Page 7

    07/2005 1 Restrictions 1.7 Restrictions due to missing PLC © Siemens AG 2005 All Rights Reserved SINUMERIK 840D VNCK Restrictions (FBVNCK) - 07/2005 Edition 1-7 1.7 Restrictions due to missing PLC VNCK does not include a PLC. However, the PLC logic and PLC-controlled motions can be simulate...

  • Page 8

    1 Restrictions 07/2005 1.10 Restrictions concerning HMI-Advanced © Siemens AG 2005 All Rights Reserved 1-8 SINUMERIK 840D VNCK Restrictions (FBVNCK) - 07/2005 Edition OSS 6 Smoothing tool orientation at end of block OSSE 6 Smoothing tool orientation at start and end of block OST1 Oscillatin...

  • Page 9

    07/2005 1 Restrictions 1.11 Bug Report and Temporary Restrictions © Siemens AG 2005 All Rights Reserved SINUMERIK 840D VNCK Restrictions (FBVNCK) - 07/2005 Edition 1-9 1.11 Bug Report and Temporary Restrictions Using VNCRegisterCommand() with the commandType VNC_REGISTER_CMD_CHANNEL_SYNC ca...

  • Page 10

    1 Restrictions 07/2005 1.10 Bug Report and Temporary Restrictions © Siemens AG 2005 All Rights Reserved 1-10 SINUMERIK 840D VNCK Restrictions (FBVNCK) - 07/2005 Edition

  • Page 11

    To Siemens AG Suggestions Corrections A&D MC MT 2 Postfach 3180 For publication/manual: SINUMERIK 840D D-91050 Erlangen Phone: +49 (0) 180 / 5050 – 222 [Hotline] Fax: +49 (0) 9131 / 98 – 63315 [Documentation] Email: motioncontrol.docu@siemens.com Virtual NCK for Simulation Restric...

  • Page 12

x