Navigation

  • Page 1

    VMC SERIES VERTICAL MACHINING CENTER OPERATION MANUAL (ELECTRICS) SHENYANG MACHINE TOOL CO., LTD CHINA CZECHVERTICAL MACHINE TOOLDEPT

  • Page 2

    China Czecho Vertical Machining Center Works IThis document is applied to Model VMC650e、VMC700、VMC850、VMC850e、VMC1000、VMC1100、VMC1300、VMC1600、VMC700B、VMC850B、VMC1000B、VMC1100B、VMC1300B、VMC1600B、VMC2100B、VMC700P、VMC850P、VMC1000P、VMC1100P、VMC1300P、VMC1600P...

  • Page 3

    VMC Seies Prefacr e China Czecho Vertical Machining Center Works II Warning Read and study the security policies carefully before the product configuration, operation, and maintenance. Failure to comply with the relevant security policies and other warnings described in the operating manual m...

  • Page 4

    VMC Series Preface China Czecho Vertical Machining Center Works IIIPreface 1. Purpose of Using the Machine VMC Series Machines are machining center tools controled by the CNC (computer numerical control device) for...

  • Page 5

    VMC Seies Prefacr e China Czecho Vertical Machining Center Works IVMaintenance Precautions Warning Before the baffle plate is removed for the purpose of maintenance, the circuit breaker in the electrical cabinet must be disconnected. Otherwise, the machine may bring injuries or electric shock...

  • Page 6

    VMC Series Preface China Czecho Vertical Machining Center Works Vmarks. I Overview………….. Explains the subjects, names of various parts and mechanical material adopted along with the machine....

  • Page 7

    VMC Seies Prefacr e China Czecho Vertical Machining Center Works VISafety Policies Before using the machine, it is necessary to read and fully understand the contents of the safety issues and relevant functions. Operations without full understanding of the content may lead to unexpected acci...

  • Page 8

    VMC Series Preface China Czecho Vertical Machining Center Works VII2. Warnings Warning Before the configuration, operation, and maintenance of the machine, please read carefully the pages related to safety policies. ...

  • Page 9

    VMC Seies Prefacr e China Czecho Vertical Machining Center Works VIIIBefore processing, it should be recognized that the tool has been effectively installed in the tool component. If the installation is improper, the tool may come off and damage the work-piece and the machine. Before processin...

  • Page 10

    VMC Series Preface China Czecho Vertical Machining Center Works IXIt should be noticed that although the circuit breaker in the electrical cabinet is disconnected, the power supply at the circuit breaker side is still co...

  • Page 11

    VMC Seies Prefacr e China Czecho Vertical Machining Center Works XConnections of the emergency stop to the external equipment should be effectively implemented. Accidents with inadequate connections may lead to injuries or damage to the tools due to malfunctioning of the emergency stop device....

  • Page 12

    VMC Series Preface China Czecho Vertical Machining Center Works XIFlammable and incendiary materials such as dilute agent, gasoline, paper, wood, cloth, fiber, and aerosol sprays are not allowed around or near the machin...

  • Page 13

    VMC Seies Prefacr e China Czecho Vertical Machining Center Works XIIh) Maintenance Warning Inspection and maintenance should be carried out regularly. The inspection items described in the maintenance sections of the manual must be implemented. Otherwise, the machine will cause death or in...

  • Page 14

    VMC Series Preface China Czecho Vertical Machining Center Works XIII3. Warning Labels and Signs Pay more attenion to the parts with labels in the day-to-day operations. The machine is with the following labels on. The...

  • Page 15

    VMC Series Contents China Czecho Vertical Machining Center Works XIVTABLE OF CONTENTS SHENYANG MACHINE TOOL (GROUP) CO., LTD. ........................................................................ I PREFACE ......................................................................................

  • Page 16

    VMC Series Contents China Czecho Vertical Machining Center Works XV1.1.5 CALLING PROGRAMS IN THE MEMORY ....................................................................... - 24 - 1.2 PROGRAMMING ........................

  • Page 17

    VMC Series Contents China Czecho Vertical Machining Center Works XVI5.1.2 ATTENTIONS FOR TOOL CHANGE OF PLATE MAGAZINE: ................................... - 57 - 5.1.3 ATTENTIONS FOR TOOL CHANGE OF CHAIN MAGAZINE: ................................... - 57 - 5.2 TOOL CHANGE EXECUTION WITH M C...

  • Page 18

    VMC Series Contents China Czecho Vertical Machining Center Works XVII7.7.1 WATER COOLING ................................................................................................................... - 77 - 7.7.2 IN...

  • Page 19

    VMC Series Contents China Czecho Vertical Machining Center Works XVIIIAPPENDIX ........................................................................................................................................ - 127 - A LIST OF G CODES ......................................................

  • Page 20

    VMC Series Overview China Czecho Vertical Machining Center Works - 1 - . Overview

  • Page 21

    VMC Series Overview China Czecho Vertical Machining Center Works - 2 -1 Overview VMC Series Machine Tools belong to vertical machining centers controlled by CNC system to realize cutting, like drilling, tapping and milling. Please don’t use the machine tool for other purposes. Please don...

  • Page 22

    VMC Series Overview China Czecho Vertical Machining Center Works - 3 -1.1 Features (1) Linear and curve machining In milling operations, high-precision linear and curve machining can be performed from different angles. (2) Rigid tapping In the rigid tapping w...

  • Page 23

    VMC Series 2.Basic Operations China Czecho Vertical Machining Center Works - 4 -2 Basic Operations Standard interface for FANUC series over FANUC Series-21I Function keys are used to select the category of ...

  • Page 24

    VMC Series Routine Run China Czecho Vertical Machining Center Works - 5 - . Routine Run

  • Page 25

    VMC Series 1. Power On/Off - China Czecho Vertical Machining Center Works - 6 -1 Power On/Off The input power supply for the machine tools of this series (standard type) is of three-phase and four-wire system with 3~380V, 50HZ. In additi...

  • Page 26

    VMC series 1. Power ON/OFF China Czecho Vertical Machining Center Works - 7 -1.1 Power On 1) Set the handwheel of the breaker on the cabinet door of the control device to the position “ON” and to the position where a sound of “...

  • Page 27

    VMC Series 1. Power On/Off - China Czecho Vertical Machining Center Works - 8 -1.2 Power Off 1) Make sure the indicator for button CYCLESTART on the operation panel goes out. 2) Make sure all the movable parts of the machine are stopped. ...

  • Page 28

    VMC Series 2. Emergency Stop China Czecho Vertical Machining Center Works - 9 -2 Emergency Stop Warning Emergency stop button operation should be first implemented in the event of the failure of the machine. It is necessary to well prepare...

  • Page 29

    VMC Series 3 Open/Close the Safety door - China Czecho Vertical Machining Center Works - 10 -3 Open/Close the Safety Door Warning Make sure that the Z axis (spindle nose) won’t descend before opening the safety door. The operation...

  • Page 30

    VMC Series 3. Open/Close the Safety Door China Czecho Vertical Machining Center Works - 11 -stopped. When the safety door is closed, the spindle and the axes will halt. NOTE:If you want to work when the safety door open , you must let...

  • Page 31

    VMC Series 4 Preparation Program - China Czecho Vertical Machining Center Works - 12 -4 Preparation Program (CNC Operation) Calling programs Three methods are available. 1.Press the mode selection key [AUTO] , switching to the running mode. ...

  • Page 32

    VMC Series 5. Dry Run China Czecho Vertical Machining Center Works - 13 -5 DRY Run 5.1 DRY Run Tool speed is corresponding to the parameter value, and has no relationship with the feed speed instructed in the program. The function c...

  • Page 33

    VMC Series 5.Dry run - China Czecho Vertical Machining Center Works - 14 - Max. Cutting feed speed………… .set by parameter No.1422 Rapid speed………………. .set by parameter No.1420 Dry run speed ………………… ....

  • Page 34

    VMC Series 6. Automatic Running China Czecho Vertical Machining Center Works - 15 -6 Automatic Running (CNC Operation) 6.1 Start of Automatic Running By means of pressing the cycle star...

  • Page 35

    VMC Series 6.Automatic Running - China Czecho Vertical Machining Center Works - 16 -6.3 Restart of Automatic Running By means of pressing the key [CYCLE START], it is able to restart the automatic running, and in this case, the indicating light of ...

  • Page 36

    VMC Series Operation Details China Czecho Vertical Machining Center Works - 17 - .Operation Details

  • Page 37

    VMC Series 1. Create Programs - China Czecho Vertical Machining Center Works - 18 -1 Create Programs 1.1 Edit Programs 1.1.1 Create Programs 1) Select EDIT mode. 2) Press the function key < PROG > to display program menu. 3) Enter program No....

  • Page 38

    VMC Series 1. Create Programs China Czecho Vertical Machining Center Works - 19 - Steps: 1) Press the address key . 2) Use value key to enter. – If only S1 is entered, it will be unable t...

  • Page 39

    VMC Series 1. Create Programs - China Czecho Vertical Machining Center Works - 20 -Searching for program start position The cursor may skip to the beginning of the program. And the searching in which the cursor moves to the beginning of the program is ca...

  • Page 40

    VMC Series 1. Create Programs China Czecho Vertical Machining Center Works - 21 - 2 Use Address/Value key to enter.. 3 Press the key to edit. Modify a word Steps: 1 Search or scan t...

  • Page 41

    VMC Series 1. Create Programs - China Czecho Vertical Machining Center Works - 22 -2 Use Address/ Value key to enter. 3 Press the key to edit. Delete a word Steps 1 search or scan the word to be deleted. 2 Press the key to edit. Take deleting X100.0...

  • Page 42

    VMC Series 1. Create Programs China Czecho Vertical Machining Center Works - 23 -1.1.3 Deleting Programs One or more than one segments in a program can be deleted. Steps: By means of f...

  • Page 43

    VMC Series 1. Create Programs - China Czecho Vertical Machining Center Works - 24 -1.1.4 Confirming Program No. in the Memory 1) Select EDIT mode and then press the function key [(PORT)]. 2) By means of pressing key [NEXT PROGRM] or [PREV PROGRM], disp...

  • Page 44

    VMC Series 1. Create Programs China Czecho Vertical Machining Center Works - 25 -1.2 Programming 1.2.1 Spindle Function (S Function) Method to specify spindle velocity with the code ...

  • Page 45

    VMC Series 1. Create Programs - China Czecho Vertical Machining Center Works - 26 -It is similar to M00,and after a specified program segment M01 has been executed, automatic operation will be stopped. However, the code is only valid when the switch [A...

  • Page 46

    VMC Series 1. Create Programs China Czecho Vertical Machining Center Works - 27 -1.2.3 Tool Function (T Function) Tool selection function The tool mounted on the machine can be selected by...

  • Page 47

    VMC Series 1. Create Programs - China Czecho Vertical Machining Center Works - 28 - Explanation: After positioning along X-axis and positioning along Y-axis are completed, rapidly move to the horizontal position of point R. Carry out the tapping oper...

  • Page 48

    VMC Series 1. Create Programs China Czecho Vertical Machining Center Works - 29 -It is available to use one the following three methods to specify the rigid tapping method: - specify M29...

  • Page 49

    VMC Series 1. Create Programs - China Czecho Vertical Machining Center Works - 30 -For example Z-axis feed speed 1000mm/min Spindle speed 1000 min –1 Pitch 1.0mm <programming for feed/min> G94; specify feed/min G00 X120.0 Y100.0; positioning M29 S...

  • Page 50

    VMC Series 1. Create Programs China Czecho Vertical Machining Center Works - 31 - Explanation After positioning along X-axis and positioning along Y-axis are completed, rapidly move to th...

  • Page 51

    VMC Series 1. Create Programs - China Czecho Vertical Machining Center Works - 32 -please refer to FS16i/18i for execution. - Switching of axes Before switching drilling axis, it is necessary to cancel the fixed cycle. If the switching of drilling axi...

  • Page 52

    VMC Series 1. Create Programs China Czecho Vertical Machining Center Works - 33 -G00 X120.0 Y100.0; positioning M29 S1000; specify rigid tapping mode G74 Z-100.0 R-20.0 F1.0; rigid tapping

  • Page 53

    VMC Series 2. Displaying & Changing Parameters - China Czecho Vertical Machining Center Works - 34 -2 Displaying & Changing Parameters 2.1 Displaying Parameters Operation steps are as follows: 1. After pressing the function key on MDI panel for several...

  • Page 54

    VMC Series 2. Displaying & Changing Parameters China Czecho Vertical Machining Center Works - 35 -2.2 Changing Parameters (by MDI Panel) Operation steps are as follows: 1. Select MDI mode, or emergen...

  • Page 55

    VMC Series 2. Displaying & Changing Parameters - China Czecho Vertical Machining Center Works - 36 - If you want to input data continuously from the selected parameter number, it is available to use sign “;” to separate the input between data. [for e...

  • Page 56

    VMC Series 2. Displaying & Changing Parameters China Czecho Vertical Machining Center Works - 37 -2.4 Changing Data of Work Piece Coordinate System The coordinate system set for machining a work pi...

  • Page 57

    VMC Series 2. Displaying & Changing Parameters - China Czecho Vertical Machining Center Works - 38 -(1) If the work piece coordinate system has been set by G92 or automatically set by the set work piece coordinate system, the absolute instruction specified s...

  • Page 58

    VMC Series 2. Displaying & Changing Parameters China Czecho Vertical Machining Center Works - 39 -2.4.3 Changing Work piece Coordinate System By changing the offset value of an external work piece o...

  • Page 59

    VMC Series 2. Displaying & Changing Parameters - China Czecho Vertical Machining Center Works - 40 -value of coordinate system will be added to the offset values of all work piece origins, which means that all work piece coordinate system shall shift for the...

  • Page 60

    VMC Series 2. Displaying & Changing Parameters China Czecho Vertical Machining Center Works - 41 -2.5 Changing User Macro Program Variable Although subprogram is quite important to a repeatable ope...

  • Page 61

    VMC Series 2. Displaying & Changing Parameters - China Czecho Vertical Machining Center Works - 42 - Table 15.1 Variable Variety Variable No. Variable Variety Function #0 Always blank The variable shall be always blank, not able to substitute any value. #1...

  • Page 62

    VMC Series 2. Displaying & Changing Parameters China Czecho Vertical Machining Center Works - 43 -written, but not to be read. (a) Referring variable While a defined variable is referred, the addre...

  • Page 63

    VMC Series 2. Displaying & Changing Parameters - China Czecho Vertical Machining Center Works - 44 -2.5.2 Setting Displayed Variable Value - While the variable value is under blank status, it means that the variable is...

  • Page 64

    VMC Series 3. Manual Operations China Czecho Vertical Machining Center Works - 45 - 3 Manual Operations 3.1 Operation of the Spindle S instruction can be set by MDI panel. The running sp...

  • Page 65

    VMC Series 4. Automatic Running - China Czecho Vertical Machining Center Works - 46 -4 Automatic Running 4.1 MDI Running Under MDI mode, a program with up to 10 rows can be edited by MDI panel under universal mode, and it can be executed under MDI mode. MDI ope...

  • Page 66

    VMC Series 4. Automatic Running China Czecho Vertical Machining Center Works - 47 -b.The other method is to press the key. At this moment, it is necessary to set the parameter MCL (No.3203#...

  • Page 67

    VMC Series 4. Automatic Running - China Czecho Vertical Machining Center Works - 48 -is not necessary to return to the beginning of the program for M30 (it is necessary to return to the beginning of the program for M99). Deleting a program -Under MDI mode, the ...

  • Page 68

    VMC Series 4. Automatic Running China Czecho Vertical Machining Center Works - 49 -- Calling a macro program While it is available with a user macro program, the macro programs can be edited ...

  • Page 69

    VMC Series 4. Automatic Running - China Czecho Vertical Machining Center Works - 50 -Explanation Execution of memory operation Execute the following programs after starting memory operation: 1) Read a command for a program block from the specified program. 2) ...

  • Page 70

    VMC Series 4. Automatic Running China Czecho Vertical Machining Center Works - 51 -4.3 Remote Control Running Under DNC operation mode, by starting automatic operation, while reading of pr...

  • Page 71

    VMC Series 4. Automatic Running - China Czecho Vertical Machining Center Works - 52 - <12 softkey-type program check menu> During DNC operation, the currently executed program will be displayed on the program check menu and program menu. The p...

  • Page 72

    VMC Series 4. Automatic Running China Czecho Vertical Machining Center Works - 53 -Limitation - Limit of characters At most, 256 characters can be displayed in the program, and therefore, t...

  • Page 73

    VMC Series 4. Automatic Running - China Czecho Vertical Machining Center Works - 54 -If it is requested to release the single-block program, it is available to press [SINGLE BLOCK] (single-block) to set it to OFF. 4.4.2 Re-start Automatic Running after Feed Hold...

  • Page 74

    VMC Series 4. Automatic Running China Czecho Vertical Machining Center Works - 55 -4.4.8 Rapid Movement Override It is allowed to set rapid movement override to 100%, 50%, 25% or F0. Rapid...

  • Page 75

    VMC Series 4. Automatic Running - China Czecho Vertical Machining Center Works - 56 - NOTE:After the implement of the program about handwheel suspension. Manual must be implement to reference Point. Otherwise, the collision knife incident and so on will be made ...

  • Page 76

    VMC Series 5. Tool Change China Czecho Vertical Machining Center Works - 57 -5 Tool Change 5.1 Attentions for Tool Change 5.1.1 Attentions for tool change of turret magazine: 1) Never...

  • Page 77

    VMC Series 5. Tool Change - China Czecho Vertical Machining Center Works - 58 -5.2 Tool Change Execution with M Codes and T Codes While executing tool change with programs, the following instructions can be specified by M06. M06 T__ The ...

  • Page 78

    VMC Series 5. Tool Change China Czecho Vertical Machining Center Works - 59 - 2) Manual tool change It is dangerous to change tools in manual modes, and...

  • Page 79

    VMC Series 5. Tool Change - China Czecho Vertical Machining Center Works - 60 - 5.4 Tool Change of Plate Tool Magazine 5.4.1 Operation steps of automatic and manual tool change 1) Automatic tool change ...

  • Page 80

    VMC Series 5. Tool Change China Czecho Vertical Machining Center Works - 61 -5.4.2 Tool change actions of machine tool and magazine Tool change acti...

  • Page 81

    VMC Series 5. Tool Change - China Czecho Vertical Machining Center Works - 62 -should be very familiar with the techniques of tool change during the operation of manual tool change. The introduction of manual tool change is only for tool ch...

  • Page 82

    VMC Series 5. Tool Change China Czecho Vertical Machining Center Works - 63 -Fig 1: action and tools are safely clamped on the chain. The spindle send off air to blow the water and dust ...

  • Page 83

    VMC Series 5. Tool Change - China Czecho Vertical Machining Center Works - 64 -Fig 2: Fig 3: Original position of magazine Tool change position of magazine Original position of magazine Tool change position of magazin...

  • Page 84

    VMC Series 5. Tool Change China Czecho Vertical Machining Center Works - 65 -Fig 4: Fig 5: Fig 6: Tool change position of magazine Tool change position of magaz...

  • Page 85

    VMC Series 5. Tool Change - China Czecho Vertical Machining Center Works - 66 -Fig 7: Fig 8: Fig 9: Tool change position of magazine Tool change position of magazine Tool change position of magazine Original posi...

  • Page 86

    VMC Series 5. Tool Change China Czecho Vertical Machining Center Works - 67 -Fig 10: Fig 11: Fig 12: Tool change position of magazine Tool change position of ...

  • Page 87

    VMC Series 5. Tool Change - China Czecho Vertical Machining Center Works - 68 -Fig 14: Fig 13: 5.6 Treatment of Tool Change Errors During changing tools, if the reset button is pressed, the tool change will be stopped a...

  • Page 88

    VMC Series 5. Tool Change China Czecho Vertical Machining Center Works - 69 -2) Manual rotation of tool magazine when magazine is not rotated to the desired position or the chain is not ...

  • Page 89

    VMC Series 6. Spindle Function - China Czecho Vertical Machining Center Works - 70 -6 Spindle Function 6.1 Spindle Rotating Viewing from the spindle motor and looking at the front end of the spindle, rotating direction of the spindle is defi...

  • Page 90

    VMC Series 6. Spindle Function China Czecho Vertical Machining Center Works - 71 -spindle rotate. 3. Press the key [SPINDLE STOP] for stopping spindle to stop the spindle. Notes: the spindl...

  • Page 91

    VMC Series 6. Spindle Function - China Czecho Vertical Machining Center Works - 72 - Notices: 1. At most, it is available to magnify the graph of load meter by 200%. 2 Graph for speed meter will be displayed according to the ratio of the curr...

  • Page 92

    VMC Series 6. Spindle Function China Czecho Vertical Machining Center Works - 73 -The operations for the spindle are the same as with the normal mechanical spindle operations, i.e. the spin...

  • Page 93

    VMC Series 7. Auxiliary Functions of Machine - China Czecho Vertical Machining Center Works - 74 -7 Auxiliary Functions of Machine 7.1 Hydraulic Station Hydraulic station can be used in various applications as optional functions, especially in the cla...

  • Page 94

    VMC serial 7. Auxiliary Functions of machine China Czecho Vertical Machining Center Works - 75 -the operations of buttons: M72—— chip forward; M73—— chip reverse; M74——cancel chip conveyi...

  • Page 95

    VMC Series 7. Auxiliary Functions of Machine - China Czecho Vertical Machining Center Works - 76 -system; the system will compare the measured data with the required actual dimensions, and then compensate the differences in programs to get the high effic...

  • Page 96

    VMC serial 7. Auxiliary Functions of machine China Czecho Vertical Machining Center Works - 77 -cooling of spindle and oil cooling of spindle; for example, in machining steel work-piece, oil is the me...

  • Page 97

    VMC Series 7. Auxiliary Functions of Machine - China Czecho Vertical Machining Center Works - 78 -7.8 Machine Illumination Machine illumination mainly consists of electric cabinet illumination and work-piece illumination. For the serial machines, the e...

  • Page 98

    VMC serial 7. Auxiliary Functions of machine China Czecho Vertical Machining Center Works - 79 -7.12 Water Gun and Air Gun There is water gun or air gun on the machine. Or water gun and air gun are e...

  • Page 99

    VMC Series 8 Di splaying of Alarm, Opera tion & Di agnosis - China Czecho Vertical Machining Center Works - 80 -8 Displaying of Alarm, Operation & Diagnosis 8.1 CNC Interface 8.1.1 Alarm information interface While alarm occurs, the men...

  • Page 100

    VMC Series 8. Displaying of Alarm, Operation & Diagnosis China Czecho Vertical Machining Center Works - 81 -8.1.2 Operation information interface While alarm occurs, the menu for OPERATOR MESSAGE will b...

  • Page 101

    VMC Series 9 .Over-tr avel Releases - China Czecho Vertical Machining Center Works - 82 -9 Over-travel Releases The case that the coordinate value of each axis exceeds specified scope is called over-travel. If over-travel occurs, there will be ...

  • Page 102

    VMC Series 10. Release of Tool Capture Status China Czecho Vertical Machining Center Works - 83 -10 Release of Tool Capture Status If the tool has been exactly inserted into the work piece while th...

  • Page 103

    VMC Series 11. Inpput/Out Data - China Czecho Vertical Machining Center Works - 84 -11 Input/Output Data It is available to use memory to input/output data. Set the input/output channel to 4 (parameter No. 20), and then it is able to browse t...

  • Page 104

    VMC Series 11. Input/Output Data China Czecho Vertical Machining Center Works - 85 -3. 3 Press the right softkey (key for menu continuity) 4. 4 Press the softkey[CARD]to display follow...

  • Page 105

    VMC Series 11. Inpput/Out Data - China Czecho Vertical Machining Center Works - 86 -11.2 Searching File Steps: 1 Press the EDIT switch on the operation panel of the machine. 2 Press the function key PROG. 3 Press the right softkey (key for me...

  • Page 106

    VMC Series 11. Input/Output Data China Czecho Vertical Machining Center Works - 87 -11.3 Reading File Steps 1. Press the EDIT switch on the operation panel of the machine. 2. Press the fun...

  • Page 107

    VMC Series 11. Inpput/Out Data - China Czecho Vertical Machining Center Works - 88 - 7. Type file number “20” by MDI panel, and then press the softkey [F SET] (setting file) to set the file number. Type the program No.“120”, and then press...

  • Page 108

    VMC Series 11. Input/Output Data China Czecho Vertical Machining Center Works - 89 -11.4 Writing File Steps 1. Press the EDIT switch on the operation panel of the machine. 2. Press the f...

  • Page 109

    VMC Series 11. Inpput/Out Data - China Czecho Vertical Machining Center Works - 90 - Explanation – register the same file name If the file with the same file name has already been saved in the memory card, the original file in the memory card ...

  • Page 110

    VMC Series 11. Input/Output Data China Czecho Vertical Machining Center Works - 91 -6. Set the file No. to be deleted by softkey [DELETE] at first, and then press the softkey[EXEC]to ...

  • Page 111

    VMC Series 11. Inpput/Out Data - China Czecho Vertical Machining Center Works - 92 -3. Repeatedly press the softkey on the right side. 4. Press the softkey[ALL IO]to display following screen: Upper part: file contents saved in the memory c...

  • Page 112

    VMC Series 11. Input/Output Data China Czecho Vertical Machining Center Works - 93 - – Display of program contents Display of program contents is not in accordance with parameter NAM (No.3...

  • Page 113

    VMC Series 11. Inpput/Out Data - China Czecho Vertical Machining Center Works - 94 -G92X-11.3Y2.33 · · M30 % - data input/output by ASCII codes has no relationship with set parameters (ISO/EIA). - Parameter NCR (No.0100#3) can be used to spe...

  • Page 114

    VMC Series 11. Input/Output Data China Czecho Vertical Machining Center Works - 95 - Table for Error Codes of the Memory Card Code Meaning 99 A part before FTA field of the memory card has b...

  • Page 115

    VMC Series 12. Tool Life Managemeng Function - China Czecho Vertical Machining Center Works - 96 -12 Tool Life Management Function General By this function, it is able to manage the life (usage times and usage period) of the tools which h...

  • Page 116

    VMC Series 12. Tool Life Management Function China Czecho Vertical Machining Center Works - 97 -12.1 Data for Managing Tool Life Data for managing tool life consists of tool group number, specified co...

  • Page 117

    VMC Series 12. Tool Life Managemeng Function - China Czecho Vertical Machining Center Works - 98 -12.2 Recording, Modifying and Deleting the Data for Managing Tool Life By editing the program for tool-life management data, the data in the...

  • Page 118

    VMC Series 12. Tool Life Management Function China Czecho Vertical Machining Center Works - 99 -Add and modify tool-life management data Delete tool-life management data Set the counting type for tool...

  • Page 119

    VMC Series 12. Tool Life Managemeng Function - China Czecho Vertical Machining Center Works - 100 -Notices: 1 While command Q is omitted, set value of parameter LTM (No.6800#2) will be used as the counting type of the tool life. 2 G10...

  • Page 120

    VMC Series 12. Tool Life Management Function China Czecho Vertical Machining Center Works - 101 -Tool-changing type A B C D Take the tool group No. specified in the same program block as tool-changing c...

  • Page 121

    VMC Series 12. Tool Life Managemeng Function - China Czecho Vertical Machining Center Works - 102 -Counting the life for the tool of group No. 3 (counting the life of tool No. 200). - Type D for changing tools It is assumed that tool li...

  • Page 122

    VMC Series 12. Tool Life Management Function China Czecho Vertical Machining Center Works - 103 -12.5 Parameters associated with Tool-life Management [data type] Bit type GS1,GS2 Combination o...

  • Page 123

    VMC Series 12. Tool Life Managemeng Function - China Czecho Vertical Machining Center Works - 104 - [data type]bit type TSM during tool-life management, several offsets have been specified during life counting. 0: counting according...

  • Page 124

    VMC Series 12. Tool Life Management Function China Czecho Vertical Machining Center Works - 105 -1: yes E17 in the currently selected group, when deleting command for tool-life management data has been...

  • Page 125

    VMC Series 12. Tool Life Managemeng Function - China Czecho Vertical Machining Center Works - 106 -Q specification: As shown in the following example, please specify times or time for life of each group at address Q. The groups omitting add...

  • Page 126

    VMC Series 12. Tool Life Management Function China Czecho Vertical Machining Center Works - 107 -reused after M code by specified tool-life counting, and same as the status when the tool life is specifi...

  • Page 127

    VMC Series 15. High-speed Skip Function - China Czecho Vertical Machining Center Works - 108 -13 Status Indicators Red, yellow and green are separately used to specify the running status and stop status of the machine. Ex-works setting is as follows: 1) When the y...

  • Page 128

    VMC Series 14. Drilling Cycle for Small Deep Holes China Czecho Vertical Machining Center Works - 109 -14 Drilling Cycle for Small Deep Holes During drilling process, when overload torque signal (w...

  • Page 129

    VMC Series 15. High-speed Skip Function - China Czecho Vertical Machining Center Works - 110 -Explanation - Operations included in the cycle * positioning along X-axis and Y-axis * Positioning at point R along Z-axis * Cutting along Z-axis(the first cutting dep...

  • Page 130

    VMC Series 14. Drilling Cycle for Small Deep Holes China Czecho Vertical Machining Center Works - 111 -<first time> α=1.0 <after second> α=α×β÷100 β is the change rate for each d...

  • Page 131

    VMC Series 15. High-speed Skip Function - China Czecho Vertical Machining Center Works - 112 -- Single block When the operation for single block has been activated, drilling operation will stop after backward operation for each time. - Tool-feed speed overload For e...

  • Page 132

    VMC Series 15. High-speed Skip Function China Czecho Vertical Machining Center Works - 113 -15 High-speed Skip Function High-speed skip signal (connected with CNC directly without PMC) can be used to take the place...

  • Page 133

    VMC Series 15. High-speed Skip Function - China Czecho Vertical Machining Center Works - 114 -whether acceleration/deceleration, servo delay 0: be counted 1: be counted and compensate accordingly (Type A) SEB During high-speed skip function, when skip signal is switc...

  • Page 134

    VMC Series 15. High-speed Skip Function China Czecho Vertical Machining Center Works - 115 -0: valid 1: invalid Notes: 1 +MIT1 ~-MIT2<X004#2 ~#5> is only valid when parameter GSK(No.6200#0)SKIPP<G006#6&...

  • Page 135

    VMC Series 15. High-speed Skip Function - China Czecho Vertical Machining Center Works - 116 - [Data type ] bit type 9S1~9S8 For continuous high-speed skip command of G31P90 or EGB skip command of G31.8, which high-speed skip signal shall be set to be valid. Co...

  • Page 136

    VMC Series 15. High-speed Skip Function China Czecho Vertical Machining Center Works - 117 -variable #5061~#5068, and when the next high-speed skip signal is input, the variable will be renewed. When the command is...

  • Page 137

    VMC Series 16. Fixed Cycles for High-speed Positioning Drilling - China Czecho Vertical Machining Center Works - 118 -16 Fixed Cycles for High-speed Positioning Drilling 16.1 General The cycle is the drilling cycle (setting inertia movement distance on point R) us...

  • Page 138

    VMC Series 16. Fixed Cycles for High-speed Positioning Drilling China Czecho Vertical Machining Center Works - 119 - Explanation During high-speed drilling cycle of deep holes, intermission tool feed alo...

  • Page 139

    VMC Series 16. Fixed Cycles for High-speed Positioning Drilling - China Czecho Vertical Machining Center Works - 120 -additional axes, drilling operation will not be implemented. - Q Specify Q in program block for drilling operation. If they have been specified in the...

  • Page 140

    VMC Series 16. Fixed Cycles for High-speed Positioning Drilling China Czecho Vertical Machining Center Works - 121 - Explanation After positioning along X-axis and Y-axis, move to the horizontal position ...

  • Page 141

    VMC Series 16. Fixed Cycles for High-speed Positioning Drilling - China Czecho Vertical Machining Center Works - 122 -otherwise G81 will be cancelled. - Tool position offset Under this fixed cycle mode, tool position offset will be omitted, For example M3 S2000 ; ...

  • Page 142

    VMC Series 16. Fixed Cycles for High-speed Positioning Drilling China Czecho Vertical Machining Center Works - 123 - Explanation After positioning along X-axis and Y-axis, move to the horizontal position...

  • Page 143

    VMC Series 16. Fixed Cycles for High-speed Positioning Drilling - China Czecho Vertical Machining Center Works - 124 - Explanation Q represents the cutting depth of each time, and normally, it shall be specified as an increment value. In the second and subsequent tool ...

  • Page 144

    VMC Series 16. Fixed Cycles for High-speed Positioning Drilling China Czecho Vertical Machining Center Works - 125 -16.3 Parameter [data type] bit type BCR In boring cycle, the withdrawing mode shal...

  • Page 145

    VMC Series 17. Origin Restoration Method & Parameters for Machine Adjustment - China Czecho Vertical Machining Center Works - 126 -17 Origin Restoration Method & Parameters for Machine Adjustment After the connector of the pulse encoder of servo motor has be...

  • Page 146

    VMC Series Appendix China Czecho Vertical Machining Center Works - 127 - Appendix

  • Page 147

    VMC Series A List of G Codes - China Czecho Vertical Machining Center Works - 128 -A List of G Codes Preparation function is described by the value next to address G. In addition, the value defines the meaning of the command included in the program blocks. There ...

  • Page 148

    VMC Series A. Tables for G Codes China Czecho Vertical Machining Center Works - 129 - Table C.1 (a) Table for G Codes (1/4) Code Group Meaning G00 01 Positioning (rapid movement) G01 Linear interpolation (cutting feed) G02 Arc int...

  • Page 149

    VMC Series A List of G Codes - China Czecho Vertical Machining Center Works - 130 - Table C.1 (b) Table for G Codes (2/4) CodGroup Meaning G30 00 First, second, third and fourth reference points return G30.1 Changeable reference point return G31 Skip functio...

  • Page 150

    VMC Series A. Tables for G Codes China Czecho Vertical Machining Center Works - 131 -Code 码 Group Meaning G47 Tool positing offset elongation by 2 times G48 Tool positing offset reduction by 2 times G49 (G49.1) 08 Cancel of to...

  • Page 151

    VMC Series A List of G Codes - China Czecho Vertical Machining Center Works - 132 - Table C.1 (d) Table for G Codes (4/4) Code Group Meaning G80 09 Cancel fixed cycle G80.5 24 Cancel of two-group electronic gear box synchronization G80.8 34 Cancel for elect...

  • Page 152

    VMC Series B. Operation List China Czecho Vertical Machining Center Works - 133 -B Operation List Category Function PROGRAM PROTECT Key Set Parameter Write =1Mode Menu Operation EliminationComplete elimination of storage While p...

  • Page 153

    VMC Series B Operation L ist - China Czecho Vertical Machining Center Works - 134 -Category Function PROGRAM PROTECT Key Set Parameter Write =1 Mode Menu Operation device Input PMC parameter ○ Emergency stop PMCMAINTE-NANCE [I/O] (PMC) =use “←”“→”to select (device) = use “←...

  • Page 154

    VMC Series B. Operation List China Czecho Vertical Machining Center Works - 135 -Category Function PROGRAM PROTECT Key Set Parameter Write =1 Mode Menu Operation Deleting blocks ○ EDIT mode PROGRAM [EOB (;) ] of the number of ...

  • Page 155

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 136 -C Alarm List (1) Alarms associated with program operation (PS alarm) (2) Alarms associated with background edit (BG alarm) (3) Alarms associated with communication (SR alarm) The alarm No. for all these alarms a...

  • Page 156

    VMC Series C. Alarm List China Czecho Vertical Machining Center Works - 137 -Alarm No Alarm Information Description 0021 ILLEGAL PLANE SELECT An error occurs in plane selection G17~G19, recheck the program and check if paralle...

  • Page 157

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 138 -Alarm No Alarm Information Description 0041 INTERFERENCE IN CUTTER COMPENSATION Over-cutting may occur during tool radius compensation or tool-tip radius compensation. Please modify the program. 0042 G45/G48 NOT AL...

  • Page 158

    VMC Series C. Alarm List China Czecho Vertical Machining Center Works - 139 -Alarm No Alarm Information Description 0060 SEQUENCE NUMBER NOT FOUND In program NO. and sequence No. searching, there is not specified No. for [oute...

  • Page 159

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 140 -Alarm No Alarm Information Description 0079 PROGRAM NOT MATCH It is unable to check the program to be read in with the program in the storage. When parameter NPE (No.3201#6) has been set to 1, it is not allowed to c...

  • Page 160

    VMC Series C. Alarm List China Czecho Vertical Machining Center Works - 141 -Alarm No Alarm Information Description point return. Run the motor manually for one revolution and then power off the CNC and servo amplifier temporar...

  • Page 161

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 142 -Alarm No Alarm Information Description 0123 ILLEGAL MODE FOR GOTO/WHILE/DO In main program of DNC mode, there is GOTO statement or WHILE-DO statement. 0124 MISSING END STATEMENT END instruction corresponding with DO...

  • Page 162

    VMC Series C. Alarm List China Czecho Vertical Machining Center Works - 143 -Alarm No Alarm Information Description 0154 NOT USING TOOL IN LIFEGROUP H99 or D99 has been specified under the status that tool management data has no...

  • Page 163

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 144 -0202 POSITION LSI OVERFLOW While rigid tapping reading, spindle assign value is too big (system error). 0203 PROGRAM MISS AT RIGID TAPPING While rigid tapping reading, the position of rigid M code (M29) is incorrect...

  • Page 164

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 145 -0222 DNC OP. NOT ALLOWED IN BG-EDIT In background editing, try to execute the input and output operation at the same time. Please execute the correct operation. 02...

  • Page 165

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 146 -0300 ILLEGAL COMMAND IN SCALING G code which cannot be specified in ratio zoom has been specified. Please modify the program. Under T series, when following functions have been specified in the ratio zoom, the alarm...

  • Page 166

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 147 -0310 FILE NOT FOUND The specified file cannot be found in the subprogram/macro program call. 0311 CALLED BY FILE NAME FORMAT ERROR Format of subprogram/macro progr...

  • Page 167

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 148 -0325 UNAVAILABLE COMMAND IS IN SHAPE PROGRAM The instruction which cannot be used in shape programs of composite turning fixed cycle (G70, G71, G72, and G73) has been specified. 0326 LAST BLOCK OF SHAPE PROGRAM IS A D...

  • Page 168

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 149 -0346 TOOL CHANGE ILLEGAL TOOL NUM Tool position has not been established during tool changing. 0347 TOOL CHANGE ILLEGAL COMMAND IN SAME BLK. Illegal command has be...

  • Page 169

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 150 -0361 BECAUSE THE AXIS IS MOVING, THE SUPERPOS CONTROL IS CAN’T BE USED. Try to start or release subject axis under superposition control by composite control axis selection signal while the subject axis under compos...

  • Page 170

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 151 -0372 REFERENCE RETURN INCOMPLETE Try to execute automatic returning of reference point under the status of manual returning reference point for angular axis mode or ...

  • Page 171

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 152 -0397 RTM BUFFER OVER No free space available from the buffer for real-time macro program instruction. The pre-read block number used to activate real-time macro program instruction during buffering is too big. 0398 ...

  • Page 172

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 153 -1005 X AXIS I IS LOCKED Axis X is locked and the movement of axis is forbidden. 1006 Y AXIS IS LOCKED Axis Y is locked and the movement of axis is forbidden. 1007...

  • Page 173

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 154 -1034 HYDRAULIC FAN QF8 OFF Air switch of hydraulic motor fan is off; check if short circuit occurs1035 HELIX CONYER QF9 OFF Motor starter of spiral chip conveyor is off; check if short circuit occurs1036 CHAIN CONYER ...

  • Page 174

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 155 -1066 ATC NOT IN ZERO POSITION Chain is not in 0 position, check the signal reflection of 0 position and execute the chain rotating action to 0 position 1067 IN M06,S...

  • Page 175

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 156 - 1090 MECHANICAL BRAKE HASNOT RELEASED Mechanical brake is not released completely; check the connections of hardware and check if the hardware is damaged 1091 MECHANICAL BRAKE ISWRON,REPLACE THE ROTOR Mechanica...

  • Page 176

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 157 -1117 COOLANT LEVEL LOW,ADD COOLANTWATER COOLANT LEVEL LOW,ADD COOLANT WATER 1118 1119 1120 1121 1122 SEPARATE OIL FROM WATER QF35OFF Separate oil from water ...

  • Page 177

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 158 -2022 2023 2024 2025 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035 2036 2037 2038 2039 2040 COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTES Coolant level is low, fill the cooling me...

  • Page 178

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 159 -2052 2053 2054 2055 2056 LUBRICATION PRESS LOW The pressure of lubricating oil is low; check if any looseness in connections of lubricating pipes connected ...

  • Page 179

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 160 -2090 2091 2092 PLEASE ADD LUB.OIL Please add lub. oil 2120 REPLACE CNC BATTERY QUICKLY ANDBEFORE REPLACE DO NOT POWER OFFCNC battery voltage is low, replace is quickly before turn off the CNC power. 2121 MAG INITI...

  • Page 180

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 161 -2246 FEED OVERRIDE IS ZERO FEED OVERRIDE IS ZERO 2247 STOP SPINDLE FIRST THEN UNCLAMPTOOL STOP SPINDLE FIRST THEN UNCLAMP TOOL 2250 CAN'T CYCLE START WHEN BATTERYLOW...

  • Page 181

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 162 -5046 ILLEGAL PARAMETER (S-COMP) The setting of parameters associated with flatness compensation is incorrect. The possible reasons are as follows: The axis No. not available in the parameters of movement axes or com...

  • Page 182

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 163 -5117 ILLEGAL 1ST CONTROL POINT (NURBS) The first control point is wrong, or no continuity with the previous block. 5118 ILLEGAL RESTART (NURBS) Try to restart NURBS...

  • Page 183

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 164 -5257 G41/G42 NOT ALLOWED IN MDI MODE Tool radius compensation or tool-tip radius compensation has been specified by MDI mode (based on setting of parameter MCR (No.5008#4)). 5303 TOUCH PANEL ERROR The connection of th...

  • Page 184

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 165 -5420 ILLEGAL PARAMETER IN G43.4/G43.5 The relevant parameter of tool center control is incorrect. 5421 ILLEGAL COMMAND IN G43.4/G43.5 An illegal instruction has be...

  • Page 185

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 166 -5457 G68.2 FORMAT ERROR G68.2 format is wrong.5458 ILLEGAL USE OF G53.1 G53.1 has been specified before specifying G68.2. 5459 MACHINE PARAMETER INCORRECT · Machine parameter (No.19665~19667, No.19680~19744) is inco...

  • Page 186

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 167 -· In tool center control for 5-axis machining and tool radius compensation for 5-axis machining, the instructions for type 1 and type 2 are different. · When ...

  • Page 187

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 168 - (4) Alarm under read-in status of parameters (SW alarm) Alarm No. Alarm Information Description SW0100 PARAMETER ENABLE SWITCH ON Set the parameter to the enable status. (Set parameter PWE (No.8900#0)=1) , whi...

  • Page 188

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 169 -(5) Servo alarms (SV alarm) Alarm No. Alarm Information Description SV0001 SYNC ALIGNMENT ERROR In the synchronous control of feed axis, the compensation value d...

  • Page 189

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 170 -SV0363 ABNORMAL CLOCK(INT) Alarm for abnormal clock occurs in the built-in pulse encoder. SV0364 SOFT PHASE ALARM(INT) In the built-in pulse encoder, it is detected that digital servo software is abnormal. SV0365...

  • Page 190

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 171 -SV0433 CNV. LOW VOLT DC LINK PSM: voltage of DC link drops PSMR: voltage of DC link drops. series SVU: voltage of DC link drops series SVU: voltage of DC link dr...

  • Page 191

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 172 -2.Sudden power off of amplifier. 3.A low pressure warning is issued amplifier. SV0462 SEND CNC DATA FAILED Because of the FSSB communication error, it is unable to for the slave end to receive correct data. SV0...

  • Page 192

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 173 -SV5139 FSSB:ERROR Servo initialization has not ended normally. It may caused by bad cable, or connection error between amplifier and other modules. SV5197 FSSB:OPE...

  • Page 193

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 174 -(6) Alarms associated with overtravel (OT alarm) Alarm No. Alarm Information Description OT0500 + OVERTRAVEL ( SOFT 1 ) Has exceeded the stored travel check 1 in the positive end. OT0501 - OVERTRAVEL ( SOFT 1 ) H...

  • Page 194

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 175 -(7) Alarms associated with storage files (IO alarm) Alarm No. Alarm Information Description IO1001 FILE ACCESS ERROR Because of abnormal CNC system files (permane...

  • Page 195

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 176 -(8) Alarms asking for power off (PW alarm) Alarm No. Alarm Information Description PW0000 POWER MUST BE OFF The parameter requiring temporary power off has been set. PW0001 X-ADDRESS (*DEC) IS NOT ASSIGNED. Addres...

  • Page 196

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 177 -(9) Alarms associated with the spindles (SP alarm) Alarm No. Alarm Information Description SP0740 RIGID TAP ALARM : EXCESS ERROR During rigid tapping reading, th...

  • Page 197

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 178 -SP1227 RECEIVING ERROR (SERIAL SPINDLE) Receiving error has occurred during the communication between CNC and serial spindle amplifier. SP1228 COMMUNICATION ERROR (SERIAL SPINDLE) Communication error has occurred d...

  • Page 198

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 179 -SP1985 SERIAL SPINDLE CONTROL ERROR Automatic setting of parameter fails. SP1986 SERIAL SPINDLE CONTROL ERROR Error occurs in the control software for spindle. SP198...

  • Page 199

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 180 - (10) Alarms associated with serial spindles (SP alarm). When alarm occurs to the serial spindle, CNC will display following alarm No. to alarm: Notes *1 When the red LED of SPM is on, the alarm will be displayed by...

  • Page 200

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 181 -SP9011 SSPA:11 OVERVOLT POWER CIRCUIT 11 Check the selection of PSM. While checking input power voltage and motor deceleration, if the change of power voltage has...

  • Page 201

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 182 -SP9029 SSPA:29 OVERLOAD 29 Check and modify loading status In a certain time, continuous overload has been applied (it may occur even if motor rotation has been restricted under magnetizing status ) SP9030 SSPA:30 O...

  • Page 202

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 183 -SP9042 SSPA:42 NO 1REV SIGN OF POSITION CODER 42 Change the cable. Readjust the BZ sensing signal. 1 revolution signal of spindle position encoder (connector JY4...

  • Page 203

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 184 -SP9055 SSPA:55 ILLEGAL POWER LINE 55 Change the electromagnetic contactor. Check and modify the sequence. Status signal for power cable of electromagnetic contactor for spindle switching/output switching is abnorm...

  • Page 204

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 185 -SP9073 MOTOR SENSOR DISCONNECTED 73 Change the feedback cable. Check the shield treatment. Check and modify the connection. Adjust the sensor. Feedback cabl...

  • Page 205

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 186 - Change SPM circuit plate for controlling printing. SP9110 AMP COMMUNICATION ERROR b0 Change the communication cable between the amplifier modules. Change SPM or PSM circuit plate for controlling printing. Comm...

  • Page 206

    VMC Series Appendix C. Alarm List China Czecho Vertical Machining Center Works - 187 -Error code list (serial spindle) Notes *1 When yellow LED indicating light of SPM is ON, display the error code by a number of two digits. The error code will be di...

  • Page 207

    VMC Series C Alarm List - China Czecho Vertical Machining Center Works - 188 -10 Although the Cs contour control instruction has been input, other modes have been specified (servo mode, spindle synchronous control, orientation). Under Cs contour control instruction, please don’t select oth...

  • Page 208

    VMC Series D Recommended Flash Card China Czecho Vertical Machining Center Works - 189 -D Recommended Flash Card General The max capacity of the program memory files is 2048Mbyte (2Gbyte). For memory card program running and editing, please use t...

  • Page 209

    VMC Series E Embedded Ethernet Function - China Czecho Vertical Machining Center Works - 190 -E Embedded Ethernet Function The explanation for operation of FTP file transmission function is as follows: Steps 1. Press the function key [PRO] 2. Press the softkey[FOLDER](general view) to ...

  • Page 210

    VMC Series E Embedded Ethernet Function China Czecho Vertical Machining Center Works - 191 -equipment is embedded Ethernet port. The connection destination for host file list menu shall be determined by the following two conditions: (1) Confirm ...

  • Page 211

    VMC Series E Embedded Ethernet Function - China Czecho Vertical Machining Center Works - 192 -Create folders in the host. HOST (host) Change the connected host. Input NC programs Input the files (NC programs) stored in the host into CNC memory. Steps 1 Dis...

  • Page 212

    VMC Series F M Codes List China Czecho Vertical Machining Center Works - 193 -F M Codes List M Code No. Definition M00 Select stop M01 Select stop and press the “select stop” button on operation panel; the same effect with M00 M02 Program com...

  • Page 213

    VMC Series F M Codes List - China Czecho Vertical Machining Center Works - 194 -M31 Aim tool has changed to spindle (for tool change micro programs of manipulator tool magazine) M32 For bucket tool magazine; to make sure no tool on spindle M33 For tool magazine controlling program M34 Reserve...

  • Page 214

    VMC Series F M Codes List China Czecho Vertical Machining Center Works - 195 -M69 Select tool command (for tool change micro programs of manipulator tool magazine) M70 Reserved M71 Reserved M72 Chain chip conveyor starts or spiral chip conveyor forwar...

  • Page 215

    VMC Series G Main Electric Parts List - China Czecho Vertical Machining Center Works - 196 -G Main Electric Parts List Brand Type Specific-ation Brand Type Specific-ation Order No. Function ABS103b QF1 Main breaker SIEMENS 5SJ62027CC20 LG BKN-2A/2P QF2 Breaker for door sw...

  • Page 216

    VMC Series G Main Electric Parts List China Czecho Vertical Machining Center Works - 197 -SIEMENS 3VU13401MD00 0.24-0.4 LG MMS-32S (FX1A1B) 0.25-0.4 QF23 Lubricating motor starter SIEMENS 3VU13401MH00 1.6-2.4 LG MMS-32S (FX1A1B) 1.6-2.5 QF24 Oil m...

  • Page 217

    VMC Series G Main Electric Parts List - China Czecho Vertical Machining Center Works - 198 -SIEMENS 3TS30001XB4 LG GMD-9 KM18 Lifting pump motor contactor SIEMENS 3TF49221XB4 KM21 Spindle output switching controlling contactor SIEMENS 3TF49221XB4 KM22 Spindl...

  • Page 218

    VMC Series G Main Electric Parts List China Czecho Vertical Machining Center Works - 199 -H PMC Parameters List 1、 List of parameters K 保持型继电器 功能 备注 字节 位 K0 0 Tool set level/magazine back off switch is normal close 1 ...

  • Page 219

    VMC Series G Main Electric Parts List - China Czecho Vertical Machining Center Works - 200 -1 With filter block switch in hydraulic station 2 With oil level low switch in hydraulic station 3 With fan in hydraulic station 4 Cancel 2097 alarm 5 6 7 K5 0 1 2 3 4...

  • Page 220

    VMC Series G Main Electric Parts List China Czecho Vertical Machining Center Works - 201 -1 Filter block switch in hydraulic station is normal open 2 Oil level low switch in hydraulic station is normal open 3 Coolant box level low switch is nor...

  • Page 221

    VMC Series G Main Electric Parts List - China Czecho Vertical Machining Center Works - 202 -1 Override switch coded is Gray 2 Override switch coded is Binary 3 4 To cycle start, Z axis must be in position switch 3 5 Work piece is not clamped can cycle start 6 7 The VMC850 series ...

  • Page 222

    VMC Series H PMC Parameters List China Czecho Vertical Machining Center Works - 203 -2、 List of parameters D Data table Meaning D100 Tool number in spindle D101 Tool number in pocket 1 D102 Tool number in pocket 2 D103 Tool number in pocket 3 D1...

  • Page 223

    VMC Series H PMC Paramenters List - China Czecho Vertical Machining Center Works - 204 -3、 List of parameters T Timer Meaning TMR9 Time of pressing lubrication key to lubricate. TMR11 Time of lubrication automatically. Automatic Lubricate In automatic lubricate mode, the lubrication pump star...

  • Page 224

    VMC Series I List of Soft Switches China Czecho Vertical Machining Center Works - 205 -I List of Soft Switches Name of soft switch Meaning when connected INNER-WC Inner coolant when press [COOLANT] key OUTER-WC Outer coolant when press [...

  • Page 225

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 206 -J Position of Electric Parts on Machine

  • Page 226

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 207 -K Electric Elements Diagram

  • Page 227

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 208 -L The List Of The Directive B About Spindle Orientation point. B degree 0 0.00 1 0.09 2 0.18 3 0.26 4 0.35 5 0.44 6 0.53 7 0.62 8 0.70 9 0.79 10 0.88 11 0.97 12 1.05 13 1.14 14 1.23 15 1.3...

  • Page 228

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 209 -147 12.92 148 13.01 149 13.10 150 13.18 151 13.27 152 13.36 153 13.45 154 13.54 155 13.62 156 13.71 157 13.80 158 13.89 159 13.97 160 14.06 161 14.15 162 14.2...

  • Page 229

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 210 -319 28.04 320 28.13 321 28.21 322 28.30 323 28.39 324 28.48 325 28.56 326 28.65 327 28.74 328 28.83 329 28.92 330 29.00 331 29.09 332 29.18 333 29.27 334 29.36 335 29.44 336 29.53 337 29.62 ...

  • Page 230

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 211 -491 43.15 492 43.24 493 43.33 494 43.42 495 43.51 496 43.59 497 43.68 498 43.77 499 43.86 500 43.95 501 44.03 502 44.12 503 44.21 504 44.30 505 44.38 506 44.4...

  • Page 231

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 212 -663 58.27 664 58.36 665 58.45 666 58.54 667 58.62 668 58.71 669 58.80 670 58.89 671 58.97 672 59.06 673 59.15 674 59.24 675 59.33 676 59.41 677 59.50 678 59.59 679 59.68 680 59.77 681 59.85 ...

  • Page 232

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 213 -835 73.39 836 73.48 837 73.56 838 73.65 839 73.74 840 73.83 841 73.92 842 74.00 843 74.09 844 74.18 845 74.27 846 74.36 847 74.44 848 74.53 849 74.62 850 74.7...

  • Page 233

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 214 -1007 88.51 1008 88.59 1009 88.68 1010 88.77 1011 88.86 1012 88.95 1013 89.03 1014 89.12 1015 89.21 1016 89.30 1017 89.38 1018 89.47 1019 89.56 1020 89.65 1021 89.74 1022 89.82 1023 89.91 102...

  • Page 234

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 215 -1179 103.62 1180 103.71 1181 103.80 1182 103.89 1183 103.97 1184 104.06 1185 104.15 1186 104.24 1187 104.33 1188 104.41 1189 104.50 1190 104.59 1191 104.68 11...

  • Page 235

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 216 -1351 118.74 1352 118.83 1353 118.92 1354 119.00 1355 119.09 1356 119.18 1357 119.27 1358 119.36 1359 119.44 1360 119.53 1361 119.62 1362 119.71 1363 119.79 1364 119.88 1365 119.97 1366 120.0...

  • Page 236

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 217 -1523 133.86 1524 133.95 1525 134.03 1526 134.12 1527 134.21 1528 134.30 1529 134.38 1530 134.47 1531 134.56 1532 134.65 1533 134.74 1534 134.82 1535 134.91 15...

  • Page 237

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 218 -1695 148.97 1696 149.06 1697 149.15 1698 149.24 1699 149.33 1700 149.41 1701 149.50 1702 149.59 1703 149.68 1704 149.77 1705 149.85 1706 149.94 1707 150.03 1708 150.12 1709 150.21 1710 150.2...

  • Page 238

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 219 -1867 164.09 1868 164.18 1869 164.27 1870 164.36 1871 164.44 1872 164.53 1873 164.62 1874 164.71 1875 164.79 1876 164.88 1877 164.97 1878 165.06 1879 165.15 18...

  • Page 239

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 220 -2039 179.21 2040 179.30 2041 179.38 2042 179.47 2043 179.56 2044 179.65 2045 179.74 2046 179.82 2047 179.91 2048 180.00 2049 180.09 2050 180.18 2051 180.26 2052 180.35 2053 180.44 2054 180.5...

  • Page 240

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 221 -2211 194.33 2212 194.41 2213 194.50 2214 194.59 2215 194.68 2216 194.77 2217 194.85 2218 194.94 2219 195.03 2220 195.12 2221 195.21 2222 195.29 2223 195.38 22...

  • Page 241

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 222 -2383 209.44 2384 209.53 2385 209.62 2386 209.71 2387 209.79 2388 209.88 2389 209.97 2390 210.06 2391 210.15 2392 210.23 2393 210.32 2394 210.41 2395 210.50 2396 210.59 2397 210.67 2398 210.7...

  • Page 242

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 223 -2555 224.56 2556 224.65 2557 224.74 2558 224.82 2559 224.91 2560 225.00 2561 225.09 2562 225.18 2563 225.26 2564 225.35 2565 225.44 2566 225.53 2567 225.62 25...

  • Page 243

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 224 -2727 239.68 2728 239.77 2729 239.85 2730 239.94 2731 240.03 2732 240.12 2733 240.21 2734 240.29 2735 240.38 2736 240.47 2737 240.56 2738 240.64 2739 240.73 2740 240.82 2741 240.91 2742 241.0...

  • Page 244

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 225 -2899 254.79 2900 254.88 2901 254.97 2902 255.06 2903 255.15 2904 255.23 2905 255.32 2906 255.41 2907 255.50 2908 255.59 2909 255.67 2910 255.76 2911 255.85 29...

  • Page 245

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 226 -3071 269.91 3072 270.00 3073 270.09 3074 270.18 3075 270.26 3076 270.35 3077 270.44 3078 270.53 3079 270.62 3080 270.70 3081 270.79 3082 270.88 3083 270.97 3084 271.05 3085 271.14 3086 271.2...

  • Page 246

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 227 -3243 285.03 3244 285.12 3245 285.21 3246 285.29 3247 285.38 3248 285.47 3249 285.56 3250 285.64 3251 285.73 3252 285.82 3253 285.91 3254 286.00 3255 286.08 32...

  • Page 247

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 228 -3415 300.15 3416 300.23 3417 300.32 3418 300.41 3419 300.50 3420 300.59 3421 300.67 3422 300.76 3423 300.85 3424 300.94 3425 301.03 3426 301.11 3427 301.20 3428 301.29 3429 301.38 3430 301.4...

  • Page 248

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 229 -3587 315.26 3588 315.35 3589 315.44 3590 315.53 3591 315.62 3592 315.70 3593 315.79 3594 315.88 3595 315.97 3596 316.05 3597 316.14 3598 316.23 3599 316.32 36...

  • Page 249

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 230 -3759 330.38 3760 330.47 3761 330.56 3762 330.64 3763 330.73 3764 330.82 3765 330.91 3766 331.00 3767 331.08 3768 331.17 3769 331.26 3770 331.35 3771 331.44 3772 331.52 3773 331.61 3774 331.7...

  • Page 250

    VMC Series K Electric Elements Diagram China Czecho Vertical Machining Center Works - 231 -3931 345.50 3932 345.59 3933 345.67 3934 345.76 3935 345.85 3936 345.94 3937 346.03 3938 346.11 3939 346.20 3940 346.29 3941 346.38 3942 346.46 3943 346.55 39...

  • Page 251

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 232 -M The setting up and use of function in prohibited region The Setting Up and Use of Function in Prohibited Region function of Prohibited region: when the turntable(K16.0 = 1) or fixture(K...

  • Page 252

    VMC Series PMC Parameters List China Czecho Vertical Machining Center Works - 233 -#734 TOOL 12 radius#735 TOOL 12 length#736 TOOL 13 radius#737 TOOL 13 length#738 TOOL 14 radius#737 TOOL 14 length#740 TOOL 15 radius#741 TOOL 15 length#742 TOOL 16 radius#743 TOOL 16 length#744 TOOL 17 radius#...

  • Page 253

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 234 -2, the use of function in the prohibited region When all the data have been set by users, they can use the functions of the prohibited regions. A. the use of the machine with tool storage B...

  • Page 254

    VMC Series PMC Parameters List China Czecho Vertical Machining Center Works - 235 -N PMC Parameters List –0i-Mate-MD List of parameters K----For 0i-Mate-MD value Function BYTE bit K00 0 1 Tool set level/magazine back off switch 1 1 ATC stop switch 2 1 ATC buckle tool signal switch 3 1 ...

  • Page 255

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 236 -7 K05 0 1 2 3 4 5 6 7 1 Permit modify the NC parameter K06 0 1 2 3 4 5 6 7 1 Permit modify the PLC K07 0 1 1 With inner air coolant 2 3 1 The pressure of ai...

  • Page 256

    VMC Series PMC Parameters List China Czecho Vertical Machining Center Works - 237 -6 1 Use the handwheel of Japanese 7 K11 0 1 Separate oil from water 1 1 With gear box 2 1 X axis reference direction is minus 3 1 Y axis reference direction is minus 4 1 Z axis reference direction is minus ...

  • Page 257

    VMC Series J Position of Electris Parts on Machine - China Czecho Vertical Machining Center Works - 238 -2 1 With plate magazine REF switch 0 Without plate magazine REF switch 3 1 With water gun 0 Without water gun 4 1 The FANUC standard MCP and sub MCP 0 Without air gun 5 1 To unclamp tool spi...

x