Navigation

  • Page 1

    P0VU6E F66D> KITCHIP SHIELDCOUPLER,LEAD SCREW &GUIDECARRIAGEUu_fejRISERHAND WHEELTRANSMOUNTA&iSCREWS%oBUSHINGz$aOWASHERSCREWSSPACER(71/4X20TAPPULLEY

  • Page 2

    BEDPREPARATIONf©/ ©h£CSTEP #1TAP THESE 4 HOLES WITH THE 1/4X 20TAP PROVIDED.STEP #2.-SADECISIONMUST BE MADETO TURNTHE BEDAROUND (FIG. A)OR TOMACHINE AWAYTHE EXISTING RACKCHANNEL (FIG.B) BECAUSE THE NEWLEADSCREW CANNOT OPERATE WITHTHERACK CHANNEL INPLACE.Aj*FIG.BIF YOUMACHINE THIS AWAY,YOUCAN L...

  • Page 3

    THIS PAGE IS FOR THOSE WHO CHOOSE TO TURNTHE BED AROUND.THOSE WHOMACHINED AWAY THE RACK CHANNEL MAY DISREGARD THISPAGE.LATHE MOUNTING BOARDMOTOROOOLD MOUNT HOLESNEWMOUNT HOLESfO•7OMOUNT PLATE:IooUSE A STRAIGHT EDGE TO LOCATE THE NEW MOUNT HOLESSTEP #3WITH THE DRIVE MOTORSTILL IN PLACE.TURN THE ...

  • Page 4

    1STEP #4WITH THE BEDSECURLYFASTENED TO THE BOARD,INSTALL THETRANSMISSIONMOUNT AND ATTACH THETRANSMISSION TO IT.DO NOTTIGHTEN. LEAVEBOTHSNUG BUTMOVEABLE.afliiM(/I7 .:1_RACK CHANNEL IFYOUTURNED THE BEDAROUND.sr

  • Page 5

    STEP #5ASSEMBLE THECARRIAGE AS SHOWN.DURING ASSEMBLY ADJUST THE HANDWHEELTO HAVE .030TO .060CLEARANCE.DO NOT OVERTIGHTEN THE BUSHING SETSCREW. IF YOU DO THE HAND WHEELWILLNOT MOVE.ITHIS END OF THEBUSHING IS TO BEFLUSH WITH THEINSIDEOF THECARRIAGE.©OjVERY IMPORTANT!MAKE SURE YOUHAVE .030TO .060CL...

  • Page 6

    »/1!&*:IT IS TIMETODISCUSS THE FITOF YOUR NEW CARRIAGE.TOGET A PERFECT FEEL YOU MAY HAVE TO "LAP IT IN". THIS COULDBE DONE BY MIXING A CLEANING AGENT LIKE COMET OR AJAXWITH3 IN 1OIL OR THE LIKE.THEEASIER YOURCARRIAGE SLIDES THEMOREPRECISE YOURWORK . SPENDSOME SERIOUS TIME WITHTHIS ...

  • Page 7

    FLATmQSPACERSET SCREWSTEP #6PLACETHE 1/2" SPACER ONTHE OUTPUTSHAFTANDTHEN THE LEAD SCREW. NOTICE THE GROUND FLATONTHE OUTPUT SHAFT,MAKE SURETHE SET SCREWLINESUP WITH THEFLAT. ALSO, ROLL THE LEAD SCREW ON A FLATSURFACE TOMAKE SURE IT RUNSTRUE.IF NOT, YOUCAN PUSH ONTHECOUPLER UNTILLIT RUNS PRE...

  • Page 8

    FINALASSEMBLY:USE CAUTION WHEN SLIDING ON THE CARRIAGE.SNUG UP THETRANSMISSION TOTRANS MOUNTSCREWS BUTSTILL ALLOW MOVEMENT OF THETRANSMISSION.TIGHTEN THETRANS MOUNTSET SCREW BUTPLACE THETRANSMISSION SO THAT IT DOES NOTCONTACT THE BED.(.030CLEARANCE IS PLENTY)SLIDE THE CARRIAGE ABOUT 1/2WAY DOWN T...

  • Page 9

    "ll&r..7,v1

  • Page 10

    <•—4TAiV'v j- _IIJVf1<1-71j7*S Jr;K11pT:J.IIi•JEÿ: oiJr__r1/AA*ni£;ELi

  • Page 11

    r.Tmn/4 #11- /r»•ni/,r /i1/i,rInrMRSkii

  • Page 12

    .!* I'?J >.V&ifmJE:\Ir‘t'h'anui“irirtVr*ÿ[£-?}] '.7.i_ J**b1-.*tv.?;1*L.-T.til4;St'L ,HfW*lpVbJ'.ÿ|.S, i,?'rF ”L?rimin>: *a'fu/IPIdt..*mPIhi ;jyJrim.j:Pi»Jai_-ixj.-I.iut-rL '.V’$! miA..- 1,I'tiTJL..Jravi7.imf f#,ÿ-VVI-I*>rtdfl>L>.>1iIIpiJ :-J?AHr** bn*A3hWi ..I....

x