Navigation

  • Page 1

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm1Techno HD User Manual(HTT06021109)This document will provide a quick guide to the set up and operating procedure of the Techno HD Mini and Techno HD Series Router with a NCstudio Controlle...

  • Page 2

    2Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)TABLE OF CONTENTSI 3,Forklift Guide ............................................................... Page 3 4,Safety Instructions ................................

  • Page 3

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm3Techno HD User Manual(HTT06021109)www.technocnc.com(HTT06081112)Tel: 516-328-3970 • Email: support@technocnc.comFORKLIFT GUIDEAll Techno machines are shipped assembled and secured to a w...

  • Page 4

    4Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)1. Keepfingers,hands,andallotherobjectsawayfrommachinewhilepowerison.2. Disconnectpowertoallsystemcomponentswhennotinuse,whenchangingaccessories,andbeforeservici...

  • Page 5

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm5Techno HD User Manual(HTT06021109)WARNING! THE SPINDLE WILL BE DAMAGED IF UNBALANCED EQUIPMENT IS USED. AIR SUPPLY MUST BE FILTERED AND DRY.

  • Page 6

    6Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)The Techno HD Mini Router is powered by 220 Volt AC and the electronics require Single Phase power.When unpacking the machine, avoid twisting any of the cables. ...

  • Page 7

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm7Techno HD User Manual(HTT06021109)2.1 Control Panel Functions.Once the electrical connections have been made, the machine is powered on by pressing the green POWER button on the front of t...

  • Page 8

    8Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)2.2 Enabling The Machine. When the machine is plugged in, the red POWER button will light up indicating the machine is powered, but motors are not yet powered. ...

  • Page 9

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm9Techno HD User Manual(HTT06021109)L1L2L3Fig. 1.1EnclosureThe Techno HD Series Router is powered by 220 Volt AC. Unless specially requested, the electronics require 3-phase power.The Electr...

  • Page 10

    10Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)Control Box Front Panel(for Vacuum System)The , highlighted above come standard if the Vacuum Table is purchased with the...

  • Page 11

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm11Techno HD User Manual(HTT06021109)I. Techno HD InstallationThe Techno HD series Router is powered by 220 Volts AC. Unless specially requested the electronics require 3 phase power.1.1 T...

  • Page 12

    12Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)1.3Take the block connector coming from the Handheld controller (fig 1.3a,) and guide it through the hole in the side of the box. Locate the controller board (f...

  • Page 13

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm13Techno HD User Manual(HTT06021109)WARNING: Direction of Pump Rotation is critical. Briefly start Pump and check rotation (arrow on casing). Exchange phases if rotation is incorrect. IF Y...

  • Page 14

    14Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)2.1 Control Panel Functions.Once the electrical connections have been made, controller is powered by turning the main power switch, on the front of the machine,...

  • Page 15

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm15Techno HD User Manual(HTT06021109)2.2 Enabling The Machine.Turn the machine on by turning the main power control switch.Fig 2.2aFig.2.2aFig.2.2cPower is now applied to the controller box....

  • Page 16

    16Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)2.4 Mode Selection.The machine has five modes that can be selected by pressing the mode button.The mode will be indicated on the bottom left side of the display...

  • Page 17

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm17Techno HD User Manual(HTT06021109)2.5 Functions of the Keys: The Function of the keys are shown below. Increase the Spindle speed.Input the number 7.Jog the X-Axis Negative direction.Inpu...

  • Page 18

    18Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)Jog the Y-axis in the positive direction. Input the number 8.Turn the spindle on/off when in Jog mode.Input the number 5.Jog the Y-axis in the negative directio...

  • Page 19

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm19Techno HD User Manual(HTT06021109)+++++++++++++2.6 Combination Keys. The Function of the keys are shown below. They are accessed by holding down Mode, then pressing the corresponding key....

  • Page 20

    20Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)III. Operating Tutorials. 3.1- Jogging the machine and changing from High/Low Jog Speed.To Jog the machine hold down one of the directional keys on the keypad. ...

  • Page 21

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm21Techno HD User Manual(HTT06021109)3.4- Adjusting the XYZ Zero position/WCS/User Origin. XYZ zero position, Working Coordinate System (WCS), and User Origin are all the same thing. Differe...

  • Page 22

    22Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)3.5- Loading a G-code File.-Unload any previous file by pressing + simultaneously. If there is a file present you will be prompted t...

  • Page 23

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm23Techno HD User Manual(HTT06021109)3.7 Running a G-code file.Once the XYZ origin has been set as per section 3.4 and the file has been loaded as per section 3.5 the user is ready to run th...

  • Page 24

    24Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)4.1- Alternating between Override and Programmed Feedrates.IV. Advanced Tutorials. The controller can run G-code files with speed set by the user on the keypad,...

  • Page 25

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm25Techno HD User Manual(HTT06021109)4.2 Setting the Override Speed for a G-code file.From the main screen, press Menu to access the Menu screen. Use the arrow keys to move the cursor and ...

  • Page 26

    26Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)4.3 Setting the Table Size.From the main screen, press Menu to access the Menu screen. Use the arrow keys to move the cursor and highlight Machine Params. Pre...

  • Page 27

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm27Techno HD User Manual(HTT06021109)4.4 Setting the Touchpad thickness.The most accurate way to get the touch pad thickness is by using the machine to measure it’s height.The user can cal...

  • Page 28

    28Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)Lubricating the X Axis.To access the X axis ball screw and rails, you must remove the covers by taking off the screws shown below.Lubrication:The HD Mini contai...

  • Page 29

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm29Techno HD User Manual(HTT06021109)Clean off any debris and apply a light coat of oil on the rails.Clean off any debris and apply a light coat of oil on the ball screw. Access the rails b...

  • Page 30

    30Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)V. HD Machine Lubrication.5.1 Lubricating the X-Y Rack and Pinion.Lubricationisimportantwithrackandpiniongearingsystems.Athinfilmofgreaseshouldalwaysbepresenton...

  • Page 31

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm31Techno HD User Manual(HTT06021109)IV. AppendixUnzip the files and copy them into the root directory of a USB stick. The password is techno, if there is a password.Place USB in the port on...

  • Page 32

    32Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)Notes On the G-code FileThe controller will recognize files with the extension .nc, .cnc, or , .txt. If a part requires multiple tools it is best to output a di...

  • Page 33

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm33Techno HD User Manual(HTT06021109)Release the machine and Recover after a Hard stop. (Reset “E-STP” error.) +E-STOP stateE-stop state occurs when there is a hardware fault, such as ...

  • Page 34

    34Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)

  • Page 35

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm35Techno HD User Manual(HTT06021109)

  • Page 36

    36Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)

  • Page 37

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm37Techno HD User Manual(HTT06021109)

  • Page 38

    38Call: 1-516-328-3970 or actionURI(www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htmTechno HD User Manual(HTT06021109)

  • Page 39

    Call: 1-516-328-3970 or actionURI(http://www.technocnc.com/support.htm):Visit: www.technocnc.com/support.htm39Techno HD User Manual(HTT06021109)

  • Page 40

x