Navigation

  • Page 1

    TechnoInc.HTT031607031RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comINSTALLATION & SETUP TABLE OF CONTENTSi. Minimum System Requirements I. Servo Controller Card II. Riser CardIII. Techno CNC InterfaceIV. Touchpad V. Start Stop BoxVI. Machine Identifi cationsVII. ...

  • Page 2

    TechnoInc.HTT031607032RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comContinue to next page …i. Minimum System Requirements• Windows 98, ME, 2000 or XP • Pentium 3 or Celeron 600 Mhz processor• 1 available PCI slotWARNING: Power to the PC MUST be OFF during in...

  • Page 3

    TechnoInc.HTT031607033RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comContinue to next page …Upon installation, the cards in your PC may look more like this: Note: By default on any machine, the Touchpad is connected to the Touchpad Connector on the board inside of...

  • Page 4

    TechnoInc.HTT031607034RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comContinue to next page … A. If the “test passed” screen appears, click OK, the test has indicated that the touchpad is functioning properly. Click OK in Setup to exit. B. If the test fai...

  • Page 5

    TechnoInc.HTT031607035RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comContinue to next page …VI. MACHINE IDENTIFICATIONSStart-Stop BoxVacuum ON / OFFPump Switch(If Applicable)Power SwitchRG+ Servo Box 3 Front PanelThe green button is the START button, hit this button t...

  • Page 6

    TechnoInc.HTT031607036RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comContinue to next page …VII. HOW TO USE THE VACUUM TABLEVacuum Pump/Blower Cable, Motor, Starter Box & ConnectorThe machine end of the the vacuum signal connector originates behind the front contr...

  • Page 7

    TechnoInc.HTT031607037RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comVacuum Hold-Down - 1Vacuum Hold-Down - 2VII. HOW TO USE THE VACUUM TABLEThe Techno Vacuum Table is very effective in “holding down” parts to be routed. For this method to work and work well, simple...

  • Page 8

    TechnoInc.Phone: 516-328-3970 · Web: www.technocnc.com8HTT02740702Scale Factor Interface SetupIF THE VALUES ARE NOT WRITTEN ON THE FRONT LEG OF YOUR TECHNO CNC ROUTER THEN THE INTERFACE DEFAULT VALUES SHOULD APPLY.VIII. SCALE FACTOR SETUP:STEP 1: Start Techno CNC Interface.STEP 2: From the Mai...

  • Page 9

    TechnoInc.HTT031607039RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comAPPENDIX APCI CARDS CONTROL BOXESNOTE: THE MP ELECTRONICS MAY SHIP WITH GANTRY III SYSTEMS, CHECK ROUTER SPEC. SHEET FOR DETAILS.PCI Interface CardThe PCI Controller CardThis card works with:· LP(LC) ...

  • Page 10

    TechnoInc.HTT0316070310RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comAPPENDIX B

  • Page 11

    TechnoInc.HTT0316070311RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comContinue to next page …X and Z-Axes – ISEL ProductsGrease: Alvania-1, -2, -3 (Shell) for light, med. and heavy-duty apps, respectively.Oil: Renolin CLP 100 (Part No. 299020).Note: On some items yo...

  • Page 12

    TechnoInc.HTT0316070312RG Series Setup InstructionsPhone: 516-328-3970 · Web: www.technocnc.comLC/LCP/LCX/RG SERIES LUBRICATION MAINTENANCEFor regular work loads, machine maintenance is required at least once a month. The machine should also be lubricated once it is received.Warning: Before in...

x