Navigation

  • Page 1

    OKUMA MacTurn250 by S.Fukazaki Auto Operation Program Select ‚P•D RESET ‚Q•D AUTO ‚R•D ‚e ‚P (Main Prg_Oper) ‚S•D ‚e ‚P (Program Select) ‚T•D Positioning Cursor to target filename. ‚U•D ‚e 7 ( OK ) ‚V•D ‚e 8 ( Close •j OKUMA MacTurn250 by S.Fukazaki...

  • Page 2

    OKUMA MacTurn250 by S.Fukazaki Auto Operation Tool Data Adjust 1. TOOL DATA 2. F 7 (ITEM) press until •– Tool OFFSET•– screen. 3. Conform Spindle mode.•i 1spindle mode or 2spindle mode•j 4. Change the Cutting position Base or Vertical. 5. Change the Tool No. By Page key or Cursor ke...

  • Page 3

    OKUMA MacTurn250 by S.Fukazaki Setup Turret Index ‚`•D Manual ‚P•DManual move turret to X-axis soft limit position. ‚Q•DCheck the interference between turret and spindle tailstock. ‚R•DTurret Index ‚a•D MDI ‚P•DClose door. ‚Q•D MDI ‚R•DG‚Q‚PHP=4 ENTER ...

  • Page 4

    OKUMA MacTurn250 by S.Fukazaki Setup Manual Tool Exchange ‚P•D Manual Index turret. •i Refer to attached sheet.•j ‚Q•D Move Turret to the place which work tends to perform. ‚R•D Manual Tool Exchange ON ‚S•D Put Turret operation box on near place with a magnet. ‚T•D ...

  • Page 5

    OKUMA MacTurn250 by S.Fukazaki EDIT mode Create New File ‚P•DEDIT mode ‚Q•D‚e 3 (New)--- If have a One touch IGF then press ‚e ‚P (‚m‚b ) ‚R•DNew file name ENTER --------Head character must be English and max.16 characters. Example1. ‚`‚a‚b ENTER ------------------Cr...

  • Page 6

    OKUMA MacTurn250 by S.Fukazaki EDIT mode File copy then create new file 1. EDIT mode 2. Move cursor to source file name. 3. F 5 (Copy) 4. Input new file name. --------Head character must be English and max.16 characters. 5. F 1 (MD1 Copy) OKUMA MacTurn250 by S.Fukazaki Setup Chuck work / Cen...

  • Page 7

    OKUMA MacTurn250 by S.Fukazaki Setup O.D. / I.D. Clump change parameter 1. Parameter 2. ‚e 8 •iChange Screen•j 3. ‚e 3 •iChuck 1spindle•j or ‚e 4 •iChuck 2spindle•j 4. •ª move cursor to upper position. 5. ‚e 1 •iMENU•j 6. ‚e 2 •iOD•j or ‚e 3 •iID•j OKUMA...

  • Page 8

    OKUMA MacTurn250 by S.Fukazaki Setup Z-axis Zero Set by macro program 1. Put on which right offset has tool on the turret. 2. Manual turn spindle. 3. Cutting face of work piece. 4. Move turret to X-axis direction then stop the spindle.--------- Don’t move Z-axis•I•I 5. Measurement. 6. MDI...

  • Page 9

    OKUMA MacTurn250 by S.Fukazaki Setup Z-axis Zero Set•i sensor automatic move•j 1. Put sensor on the turret. 2. Manual It brings close to less than 10mm of a work. 3. MDI 4. GG2200‚U‚U ZZPP==ttoouucchh ppooiinntt •iIf value “0” then only G2‚O‚U•j 5. ENTER 6. START 7. Sensor...

  • Page 10

    OKUMA MacTurn250 by S.Fukazaki Setup Touch setter Parameter setting ‚P•D Put collect offset tool on turret. ‚Q•D Manual move turret to X-axis limit. ‚R•D Check the interference between sensor and chuck or work piece. ‚S•D Sensor advance ----- automatic change display to “Tool Da...

  • Page 11

    OKUMA MacTurn250 by S.Fukazaki Setup Tool offset (Touch setter) 1. Put tool on turret. 2. Manual move turret to X-axis limit. 3. Check the interference between sensor and chuck or work piece. 4. Sensor advance ----- automatic change display to “Tool Data” 5. It brings close to less than 2m...

  • Page 12

    OKUMA MacTurn250 by S.Fukazaki Setup Change the Transfer angle ‚P•D Sub chuck open. ‚Q•D Manual move W-axis to near the main spindle. ‚R•D MDI ‚S•D M151 ENTER ----- spindle synchronous command. ‚T•D START ------------- Attn. Spindle is rotate. ‚U•D Parameter ‚V...

  • Page 13

    OKUMA MacTurn250 by S.Fukazaki OKUMA MacTurn250 by S.Fukazaki Setup Tailstock move •iManual•j 1. Change parameter to center work. 2. Unclamp tailstocks bolt4 piece. 3. Take out bed cove. 4. Return Y-axis to origin position and X-axis to limit position. 5. Move Z-axis to connection positi...

  • Page 14

    OKUMA MacTurn250 by S.Fukazaki Setup Tailstock move •iAuto•j 1. Change parameter to center work. 2. Return Y-axis to origin position and Y-axis Off. 3. Move X-axis to limit position. 4. Retract tailstock sleeve. 5. Feed override 30% 6. Return connection 7. Ingress Feed override. 8. Move unti...

  • Page 15

    OKUMA MacTurn250 by S.Fukazaki Auto Operation Number search 1. Door close•B 2. X-axis move until limit. 3. Select the screen actual position and program. 4. RESET 5. AUTO mode 6. Single block ON 7. Feed override 0. 8. F 1 •iMain Prg_Oper•j 9. F 4 •iNumber search•j 10. N•›•›•...

  • Page 16

    OKUMA MacTurn250 by S.Fukazaki EDIT mode Data backup•i Tool/Parameter/Zero•j ‚Q•D TOOL DATA ‚R•D •„ •i Extend•j ‚S•D ‚e 7 •i D-PIP•j ‚T•D ‚e ‚Q •i Output•j ‚U•D •¨ •« poisoning cursor to file name. ‚V•D File name ENTER ‚W•D Each da...

  • Page 17

    OKUMA MacTurn250 by S.Fukazaki EDIT mode File copy from Floppy •i Floppy FD0: •\•„ Machine MD1: •j 1. Insert Floppy disk to floppy driver. 2. EDIT mode 3. ‚e 1 •i change display•j 4. ‚e 4 •i MD1&FD0•j 5. Select source file name in right side. 6. ‚e 5 •i Copy•j 7. ...

x