Navigation

  • Page 1

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com1JT0010HD NCstudio Quick Guide.This document will provide a quick guide to the set up and operating procedure of the Techno HD Series Router with a NCstudio Controller. HD series router is powered by high p...

  • Page 2

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com2JT0010HD NCstudio Quick Guide.Table of ContentsSafety InstructionsI.........Techno HD InstallationII........NCStudio Controller Functionality 2.1- Powering the Machine. 2.2- Enabling the controller. 2.3-...

  • Page 3

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com3JT0010HD NCstudio Quick Guide.1.Keep:fingers,hands,andallotherobjects away from machine while power is on.2. Disconnect power to all systemcomponentswhennotinuse,when changing accessories and before ...

  • Page 4

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com4JT0010HD NCstudio Quick Guide.I. Techno HD InstallationThe Techno HD series Router is powered by 220 Volts AC. Unless specially requested the electronics require 3 phase power.1.1 The Electronics are hous...

  • Page 5

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com5JT0010HD NCstudio Quick Guide.1.3Take the block connector coming from the Handheld controller (fig 1.3a,) and guide it through the hole in the side of the box. Locate the controller board (fig 1.3b) and ...

  • Page 6

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com6JT0010HD NCstudio Quick Guide.1.6Take the hoses from the bottom of the machine (fig 1.6a,) and attach them to the T-connector on the pump (fig 1.6b.) Fig. 1.6aFig. 1.6b1.7Once power is connected turn the ma...

  • Page 7

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com7JT0010HD NCstudio Quick Guide.2.1 Powering the Machine.Once the electrical connections have been made, controller is powered by turning the main power switch, on the front of the machine, to the on position...

  • Page 8

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com8JT0010HD NCstudio Quick Guide.2.2 Enabling The Machine.Turn the machine on by turning the main power control switch.Fig 2.2aFig. 2.2aFig. 2.2cPower is now applied to the controler box. The red light will no...

  • Page 9

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com9JT0010HD NCstudio Quick Guide.2.4 Mode Selection.The machine has five modes that can be selected by pressing the mode button.The mode will be indicated on the bottom left side of the display.The five modes ...

  • Page 10

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com10JT0010HD NCstudio Quick Guide.2.5 Functions of the Keys: The Function of the keys are shown below. Increase the Spindle speed.Input the number 7.Jog the X-Axis Negative direction.Input the number 4.Decreas...

  • Page 11

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com11JT0010HD NCstudio Quick Guide.Jog the Y-axis in the positive direction. Input the number 8.Turn the spindle on/off when in Jog mode.Input the nuber 5.Jog the Y-axis in the negative direction. Input the num...

  • Page 12

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com12JT0010HD NCstudio Quick Guide.+++++++++++++2.5 Functions of the Keys:2.6 Combination Keys. The Function of the keys are shown below. They are accessed by holding down Mode, then pressing the corresponding ...

  • Page 13

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com13JT0010HD NCstudio Quick Guide.III. Operating Tutorials. 3.1- Jogging the machine and changing from High/Low Jog Speed.To Jog the machine hold down one of the directional keys on the keypad. The keypad has ...

  • Page 14

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com14JT0010HD NCstudio Quick Guide.3.4- Adjusting the XYZ Zero position/WCS/USer Origin. XYZ zero position, Working Coordinate System (WCS), and User Origin are all the same thing. Different CAM systems and use...

  • Page 15

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com15JT0010HD NCstudio Quick Guide.3.5- Loading a File.-Unload any previous file by pressing + simultaneously. If there is a file present you will be prompted to click ok to confirm ...

  • Page 16

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com16JT0010HD NCstudio Quick Guide.3.6 Running a file.Once the XYZ origin has been set as per section 3.4 and the file has been loaded as per section 3.5 the user is ready to run the g-code file. To run the g-c...

  • Page 17

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com17JT0010HD NCstudio Quick Guide.4.1- Alternating between Override and Programmed Feedrates.IV. AdvancedTutorials. The controller can run g-code files with speed set by the user on the keypad, override speerd...

  • Page 18

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com18JT0010HD NCstudio Quick Guide.4.2 Setting the Override Speed for a G-code file.From the main screen, press Menu to access the Menu screen. Use the arrow keys to move the cursor and highlight Processing P...

  • Page 19

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com19JT0010HD NCstudio Quick Guide.4.3 Setting the Table Size.From the main screen, press Menu to access the Menu screen. Use the arrow keys to move the cursor and highlight Machine Params and press OK to sel...

  • Page 20

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com20JT0010HD NCstudio Quick Guide.4.4 Setting the touchpad thickness.The most accurate way to get the touch pad thickness is by using the machine to measure it’s height.The user can calculate the Calibration...

  • Page 21

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com21JT0010HD NCstudio Quick Guide.V. Machine Lubrication.5.1 Lubricating the X-Y Rack and Pinion. Lubrication is important with rack and piniongearingsystems.Athinfilmof grease should always be p...

  • Page 22

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com22JT0010HD NCstudio Quick Guide.IV. AppendixUnzip the files and copy them into the root directory of a USB stick. The password is techno, if there is a password.Place USB in the port on the controller box. S...

  • Page 23

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com23JT0010HD NCstudio Quick Guide.Notes On the G-code FileThe controller will recognise files with the extension .nc, .cnc, or , .txt. If a part requires multiple tools it is best to output a different file fo...

x