Navigation

  • Page 1

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com1HTT00000000HDS Series Quick Start Guide.Techno-Osai Start Up SequenceTurn the Main power switch to the ON Position.220 volts should have been attached to this switch by an electrician.The red light ...

  • Page 2

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com2HTT00000000HDS Series Quick Start Guide.The Boot Controller software will start automatically. If it does not double click on the BootController Icon on the desktop. If no text appears in the box, a...

  • Page 3

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com3HTT00000000HDS Series Quick Start Guide.The Techno interface screen will now open. There will be a warning message saying Emergency Stop Active. Click on the E-stop Reset Button to remove this warni...

  • Page 4

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com4HTT00000000HDS Series Quick Start Guide.Jogging the machine. The machine has three jog modes:-Handwheel: The machine is controlled by the handwheel on the side of the machine.-Continuous: The machin...

  • Page 5

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com5HTT00000000HDS Series Quick Start Guide.Setting the Origin/XYZ zero position.When setting an origin, make sure the correct tool is in the chuck and this tool has been identified. The T.OFFSET box in...

  • Page 6

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com6HTT00000000HDS Series Quick Start Guide.TOOLSLearning Tool Lengths.Tool lengths will record how long the tools in the holder and record the offset value. This will allow multiple tools to be used in...

  • Page 7

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com7HTT00000000HDS Series Quick Start Guide.If jogging the machine make sure one of these buttons is clicked, otherwise it will not move.This displays the Tool that is in the chuck. 1 means no offset is...

  • Page 8

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com8HTT00000000HDS Series Quick Start Guide.Loading and Running a G-Code File.The g-code file must be copied into the programs folder on the PLC directory. There is a shortcut to this on the main deskto...

  • Page 9

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com9HTT00000000HDS Series Quick Start Guide.End of File:M05 (Spindle Off)M48 (Dust shroud up)M30 (File end)So the start of a typical file will look like this. G70 G90 G40 G80 G17 ...

  • Page 10

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com10HTT00000000HDS Series Quick Start Guide.Click on G-code File to access the file menu. Locate the File you want to load.Left click on the file.Click Activate to load it to the machine.Close the wind...

  • Page 11

    Tel: 516/328-3970 · Web: http://www.technocnc.com · E-mail support@technocnc.com11HTT00000000HDS Series Quick Start Guide.The file name will now appear on the top right of the screen. You are now ready to run the file. To run the file. -Ensure that the origin and the Tool offset...

x