Navigation

  • Page 1

    XYZ Turret Mill ProtoTRAK SMX CNC Safety, Programming, Operating, & Care Manual Covers Models: • XYZ Turret Mill with 2-Axis CNC SMX SLV SMX2 SMX 1500 SMX2 SMX 2000 SMX2 SMX 3000 SMX2 • XYZ Turret Mill with 3-Axis CNC SMX SLV SMX3 SMX 1500 SMX3 SMX 2000 SMX3 SMX 3000 SMX...

  • Page 2

    Copyright © 2013 XYZ Machine Tools, Ltd. All rights are reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior...

  • Page 3

    i XYZ Machine Tools, Ltd. XYZ Turret Mill, ProtoTRAK SMX CNC Safety, Programming, Operating and Care Manual Table of Contents 5,1.0 5, 5,Introduction 5, 5, 5, 5, 1 5, 5,1.1 5, 5,Conditions 5, of This 5, Manual 5, 5, 5, 5, 5,1.2 5, 5,Manual Organization 5, 5, 5, 5, 6,2.0 6, ...

  • Page 4

    ii XYZ Machine Tools, Ltd. XYZ Turret Mill, ProtoTRAK SMX CNC Safety, Programming, Operating and Care Manual 11.1 Delete Events 11.2 Spreadsheet Editing 11.3 Erase Program 11.4 Clipboard 11.5 G Code Editing 108,12.0 108, 108,Set-Up Mode 108, 108, 108, 108,104 108, 108,12.1...

  • Page 5

    1 XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual . 1.0 Introduction Congratulations! Your new XYZ Turret Mill with the ProtoTRAK SMX CNC is an excellent all-around addition to your shop. The ProtoTRAK SMX has an easy-to-...

  • Page 6

    2 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 2.0 Safety The safe operation of your turret mill depends on its proper use and the precautions taken by each operator. Read and study this manual. Be c...

  • Page 7

    3 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Safety & Information Labels Used On The XYZ Turret Mills It is forbidden by law to deface, destroy or remove any of these labels

  • Page 8

    4 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Safety & Information Labels Used On The XYZ Turret Mills It is forbidden by law to deface, destroy or remove any of these labels

  • Page 9

    5 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Safety & Information Labels Used On The XYZ Turret Mills It is forbidden by law to deface, destroy or remove any of these labels

  • Page 10

    6 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Safety & Information Labels Used On The XYZ Turret Mills It is forbidden by law to deface, destroy or remove any of these labels

  • Page 11

    7 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Safety & Information Labels Used On The XYZ Turret Mills It is forbidden by law to deface, destroy or remove any of these labels

  • Page 12

    8 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Safety & Information Labels Used On The XYZ Turret Mills It is forbidden by law to deface, destroy or remove any of these labels

  • Page 13

    9 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 415 VOLTS Safety & Information Labels Used On The ProtoTRAK SMX CNC It is forbidden by law to deface, destroy or remove any of these labels

  • Page 14

    10 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 2.3 Safety Precautions 1. Do not operate this machine before the ProtoTRAK SMX CNC Safety, Installation, Maintenance, Service and Parts List Manual, and the Safety, Prog...

  • Page 15

    11 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 16. Avoid getting pinched in places where the table, saddle or spindle head create "pinch points" while in motion. 17. Securely clamp and properly locate the w...

  • Page 16

    12 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 3.0 Description 3.1 ProtoTRAK SMX CNC Specifications In its base form, the ProtoTRAK SMX CNC is powerful and easy to use. For turret mill applications, the two-axis CNC ...

  • Page 17

    13 XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual o Rectangular pocket o Circular profile o Rectangular profile Program pause Conrad – automatic corner radius Math helps with graphical interface Auto load of math so...

  • Page 18

    14 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual - Rectangular Island (8.7.2) - Irregular Island (8.7.3) - Irregular Profile (8.8.3) - Helix (three-axis CNC models) (8.9) - Thread milling (three-axis CNC models) (8.12) ...

  • Page 19

    15 XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual The DXF Option Consists of additional software and an Activation Password. The software can be shipped to you. See Section 3.1.8 below for instructions on ordering and o...

  • Page 20

    16 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 6. When you receive your Password Activation Number, input it into the ProtoTRAK where indicated on the screen obtained in step 2 above. Some options require you to rebo...

  • Page 21

    17 XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual : Feedrate Override to increase feedrate or spindle rpm up to 150%. : Feedrate Override to decrease feedrate or spindle rpm down to 10%. Each button push Modifies ...

  • Page 22

    18 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Emergency Stop Switch The emergency stop (E-stop) switch kills all power to the spindle and ProtoTRAK's servomotors. The computer and pendant remain powered. If the Eme...

  • Page 23

    19 XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 3.2.3 Pendant Right Side (See Figure 3.2.3) FIGURE 3.2.3 The ProtoTRAK SMX CNC right side

  • Page 24

    20 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Pendant Right Side with USB Ports Keyboard P/S2 port. This port is for the keyboard only. If this port is used, the connection must be made before the ProtoTRAK is t...

  • Page 25

    21 XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual available. Loading a new driver is not difficult for a qualified computer administrator who can access the start menu on the ProtoTRAK with a keyboard plugged in (see the...

  • Page 26

    22 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Two- and three-axis CNC Turret Mill Specifications SMX 1500 SMX2 2-Axis CNC, 3-Axis DRO SMX 2000 SMX2 2-Axis CNC, 3-Axis DRO SMX 3000 SMX2 2-Axis CNC, 3-Axis D...

  • Page 27

    23 XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Maximum Quill Travel, 2-axis CNC 127 127 127 127 Maximum Quill Travel, 3-axis CNC 115 115 115 115 Quill Diameter 86 86 105 105 Spindle Taper R8 R8 40 ISO 40 ISO Spindle...

  • Page 28

    24 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Head Lubrication Once Each Week: 1. Fill the oil cup on the front of the head with ISO 32 oil. This oil lubricates the Hi/Lo range shifter. 2. Fill the ball oiler locate...

  • Page 29

    25 XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 3.10 Work Light An halogen work light is supplied with the machine. It mounts to the left side (facing) of the column and plugs into a 110v outlet in the electrical cabi...

  • Page 30

    26 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 3.16.2 Linear Scales The ProtoTRAK SMX CNC may be configured to run either with or without Linear Scales for X and Y travel. Linear scales have a feedback resolution of 5...

  • Page 31

    27 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual 4.0 Basic Operation The ProtoTRAK SMX CNC combines the simplicity and flexibility of using a knee mill with the easy, natural user interface that makes the ProtoTRAK the top b...

  • Page 32

    28 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual If the machine has been shut off since the last time the ProtoTRAK SMX was on, you will have to press the green E-Stop Reset button on the right side of the ProtoTRAK display pen...

  • Page 33

    29 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual Functions, the operation of the coolant system may be programmed within the program events. With the Auxiliary Functions set-up, manual control of the coolant system is through t...

  • Page 34

    30 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual You may have the Math Help solutions load directly into your program. This saves you from having to write down the solution and then key it in. While you ...

  • Page 35

    31 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual The Programmable E-Head Option and TRAKing/Electronic Handwheel Option may not be turned on or off. If they are installed, they must remain active. 4.2 Machine Operation This se...

  • Page 36

    32 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual Figure 4.2.0 XYZ SMX 1500 Mill head front view. Shown without the standard quill glass scale.

  • Page 37

    33 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual 4.2.2 Table, Saddle, Knee/Clamps The table clamps are located on the front of the saddle. Rotate them clockwise until snug--overtightening is not necessary. The saddle clamp is ...

  • Page 38

    34 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual CAUTION! Never attempt to change the range selection through the High-Low-Neutral lever when the spindle is rotating. Be certain the spindle ON/OFF switch is in the Off positio...

  • Page 39

    35 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual CAUTION! It is recommended that the selector be disengaged when the spindle is not running. Never have the feed engaged when the spindle RPM is over 3000. Always leave the sel...

  • Page 40

    36 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual 4.2.12 Quill Feed Selector (Two-Axis CNC Models) Figure 4.2.10.3 Quill Feed Selector one model Figure 4.2.10.4 Quill Feed Selector one model This selector is used to set ...

  • Page 41

    37 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual _________________________________________________________________ 5.0 Definitions, Terms & Concepts 5.1 ProtoTRAK SMX CNC Axis Conventions X Axis: positive X-axis mot...

  • Page 42

    38 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Note: Tool Path programming is part of the Advanced Features Option. Programs generated by CAD/CAM systems are always generated as Tool Path programs and are run as suc...

  • Page 43

    39 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual or ABS SET key. This manual uses the term SET when either INC SET or ABS SET may be used interchangeably. 5.6 Incremental Reference Position in Programming When X, Y, Z ...

  • Page 44

    40 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Tool center means no compensation either right or left. That is, the centerline of the tool will be moved to the programmed points. 5.8 Tool Diameter Co...

  • Page 45

    41 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual FIGURE 5.8.2 In order to respect the lines defined by the programmed points, the ball end mill never touches point B. Tool starts centered over A offset up by...

  • Page 46

    42 XYZ Machine Tools, Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual For the figure below, you program an Arc event from X1, Z1 to X2, Z2, and a Mill to X3, Z3. During the programming of the Arc event, the system will prompt for Conrad a...

  • Page 47

    43 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual 6.0 DRO Mode The ProtoTRAK SMX CNC operates in DRO Mode as a sophisticated 3-axis digital readout with jog and power feed capability. 6.1 Enter DRO Mode Press MODE, select DRO...

  • Page 48

    44 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual Recall Absolute Position of One Axis: Press X or Y or Z, INC/ABS. Note the INC or ABS label for each axis. Repeat to get selected axis back to original reading. 6.3 Jog The servo...

  • Page 49

    45 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual 6.6 Go To (TRAKing/Electronic Handwheels Option) The Go To function in the DRO mode allows you to set a dimension in X, Y or Z at which you want the machine to stop moving when y...

  • Page 50

    46 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Safety, Programming, Operating & Care Manual If you press the POSN or DRILL key, the event counter will go up by one and the screen remains the same. If you press the MILL BEGIN key, the event counter stays on the same numbe...

  • Page 51

    47 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 7.0 Program Mode Getting Started & Some General Information 7.1 Programming Overview The ProtoTRAK SMX CNC makes programming easy by allowing you to program the actua...

  • Page 52

    48 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 7.3 Program Header Screen The first screen you see when you enter the Program Mode is the Program Header Screen. The Program Header Screen gives you options that apply to...

  • Page 53

    49 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Use the blank space on the lower right of the table to insert a space into the program name. Once you finish entering the letters and special characters, press the End s...

  • Page 54

    50 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual One restriction to part geometry programming is that for events to be connective, they must lay on the same plane (see Section 5.3 for a definition of planes). For this re...

  • Page 55

    51 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 1 Coolant/Air The coolant pump or air solenoid will be turned on when this event begins to run. 3 Pulse Indexer Activates a 0.3 second electronic pulse at the beginning o...

  • Page 56

    52 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual you then program. The default fixture number will be assumed if you press SET without specifying a different number. If you do specify a different fixture number that fi...

  • Page 57

    53 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 7.8 Softkeys within Events Once a geometry (Event) such as Mill or Bolt Hole is selected, the softkeys will change. See Figure 7.8 PAGE FWD: moves forward through...

  • Page 58

    54 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual When the MORE soft key is selected, the soft keys change to: After an event type is selected from the soft keys, the prompts for that event will appear on the right side...

  • Page 59

    55 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 7.11 LOOK As you program each event, it is helpful to see your part drawn. For quick graphics while in the Program Mode, press the LOOK hard key. This function is active ...

  • Page 60

    56 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual c. In Set-Up Mode "lie" about the tool diameter for the tool called out in events in "a.". Input a tool diameter equal to the actual tool diameter plu...

  • Page 61

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 57 8.0 Two-Axis Program Events This section describes the events and prompts you encounter when programming your ProtoTRAK SMX as a two-axis CNC. If you have a three-axis XY...

  • Page 62

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 58 Tool Offset: is the selection of the tool offset to right (input 1), offset to left (input 2), or tool center--no offset (input 0) relative to the programmed edge and dir...

  • Page 63

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 59 8.5.1 Circular Pocket Press the CIRCLE PCKT soft key if you wish to mill a circular pocket. Prompts for the circle pocket: X Center: is the X dimension to the center of t...

  • Page 64

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 60 Fin Feedrate: is the finish cut milling feedrate in in/min from .1 to 100, or mm/min from 5 to 2540 (up to 3800 for model SLV) Tool #: is the tool number you assign When...

  • Page 65

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 61 Note – if you press the HELP key when you are on the X1 prompt, you can adjust the step over distance of the face mill. The default is 95% of the cutter width. You ca...

  • Page 66

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 62 When the Advanced Features Option is active, press the RECT ISLAND softkey if you wish to machine a rectangular island. Prompts for the RECT ISLAND: X1 ISLAND: X dimension...

  • Page 67

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 63 CONRAD PCKT: the value of the tangential radius in the corners of the rectangular pocket that surrounds the island. FIN CUT PCKT: finish cut along the perimeter of the poc...

  • Page 68

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 64 Direction: is the clockwise (input 1), or counterclockwise (input 2) direction for milling. Tool Offset: is the selection of the tool offset to the right (input 1), offs...

  • Page 69

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 65 letters with the Engrave Event. The letters are of the font shown in the figure and all capitals. Prompts for the Engrave Event First, define the lower left corner of the...

  • Page 70

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 66 FIGURE 8.8 The above figure shows the text and special characters available for the Engrave event. Notice the field that is labeled “Text Length”. This f...

  • Page 71

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 67 not rotate another rotate event, however you can rotate a mirror event. Consider the figure below: FIGURE 8.9.2 Shape A programmed with 4 MILL events and Conrads. Us...

  • Page 72

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 68 Mirror Axis: is the selection of the axis or axes to be mirrored (input X or Y or XY, SET). X Offset: is the distance from Y absolute 0 to the Y-axis line of reflection....

  • Page 73

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 69 Figure 8.10 In the above example, the offset that puts the group of holes in the desired location is X=-1.50 and Y=-1.00. 8.11 Finishing Teach Events Teach events are ...

  • Page 74

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 70 9.0 Three-Axis Program Events This section describes the program events and prompts that are available in three-axis programming. If your ProtoTRAK SMX CNC is conf...

  • Page 75

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 71 RPM: is the spindle RPM for the event. INC SET will use the RPM of the previous event. RPM programming is available only if the Programmable Electronic Head Optio...

  • Page 76

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 72 Y Begin: is the Y dimension to the beginning of the mill cut. Z Rapid: is the Z dimension to transition from rapid to feed. Z Depth: is the depth of the cut in Z....

  • Page 77

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 73 Z Depth: is the depth of the cut in Z. If the Advanced Features Option is active, Z Begin and Z End prompts will appear in the place of Z Depth. Z Begin: is the Z...

  • Page 78

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 74 9.6.1 Circular Pocket Press the CIRCLE PCKT soft key if you wish to mill a circular pocket. Prompts for the circle pocket: X Center: is the X dimension to the cent...

  • Page 79

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 75 # Passes: is the number of cycles to machine to the final depth spaced equally from Z Rapid to Z End (hint: keep Z Rapid small). Entry mode: choose between a zigz...

  • Page 80

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 76 When the initial screen is complete, you will define the perimeter of the pocket with a series of A.G.E. Mills and A.G.E. Arcs. Programming with the Auto Geometry ...

  • Page 81

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 77 9.6.8 Face Mill (Advanced Features Option) Press Face Mill soft key if you wish to face or clean up the top of a workpiece. The cutter will automatically start...

  • Page 82

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 78 programmed rectangular perimeter (or pocket). It will then follow the perimeter, offset by the pocket finish cut. It will proceed in this manner through the number...

  • Page 83

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 79 TOOL #: is the tool number you assign. 9.7.2 Rectangular Island (Advanced Features Option) Press the RECT ISLAND softkey if you wish to machine a rectangular islan...

  • Page 84

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 80 9.7.3 Irregular Island (Advanced Features Option) Press the IRREG ISLAND key if you wish to mill an island other than a rectangle or circle. The Irregular Island g...

  • Page 85

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 81 9.8 PROFILE Events This event allows you to mill around the outside or inside of a circular or rectangular frame or an irregular profile. The irregular profile ma...

  • Page 86

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 82 Z End: is the Z dimension at the bottom of the frame; incremental is from the previous event. Conrad: is the value of the tangential radius in each corner. Direct...

  • Page 87

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 83 FIN RPM: is the spindle RPM for the finish cut. FIN RPM programming is available only if the Programmable Electronic Head Option is active. Fin Feedrate: is the fi...

  • Page 88

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 84 holes, duplicating some machined shapes, or even repeating an entire program with an offset for a second fixture. Repeat events may be "nested." That is,...

  • Page 89

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 85 FIGURE 9.10.2 Shape A programmed with 4 MILL events and Conrads. Using ROTATE, these 4 events are rotated through a 45 degree angle...

  • Page 90

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 86 Cutting Order: input 1 to cut from the lowest mirrored event to the highest (forward) and 2 to machine from the highest mirrored event to the lowest (backward). Thi...

  • Page 91

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 87 Figure 9.11 In the above example, the offset that puts the group of holes in the desired location is X=-1.50 and Y=-1.00. 9.11.1 Copy Drill to Tap The copy dril...

  • Page 92

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 88 MAJOR DIA: the largest diameter of the thread (the root for an ID thread, the crest for an OD thread). MINOR DIA: the smallest diameter of the thread (the root for ...

  • Page 93

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 89 Prompts for the Engrave Event: First, define the lower left corner of the box that will contain your text: X BEGIN: The X coordinate of where you want your text to...

  • Page 94

    XYZ Machine Tools, Ltd. XYZ Machine Tools Ltd. and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 90 TEACH DRILL- this may also be made into a bore event. See Section 9.2 for a description of Drill event prompts. TEACH MILL - a straight line that specifies the beg...

  • Page 95

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 91 10.0 Auto Geometry Engine (A.G.E.) Programming This entire section deals with the Auto Geometry Engine (A.G.E.), which is part of the Advanced Features Option. If the Adv...

  • Page 96

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 92 End A.G.E.: Ends the A.G.E. programming for the Irregular Pocket or Irregular Profile. Abort A.G.E.: Aborts all A.G.E. events. The data for all the events is lost. 10.2 A...

  • Page 97

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 93 10.3 A.G.E. Arc Prompts Press the A.G.E. ARC key. Prompts in A.G.E. Arc programming: Tangent: this refers to the tangency of the mill to the previous event. See Section 1...

  • Page 98

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 94 The Irregular Profile has no such restriction since profiles may be open or closed. Once the A.G.E. is ended, the Irregular Pocket or Irregular Profile event is complete a...

  • Page 99

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 95 Figure 10.8.1 When the Data Input Line says "Enter Guess" pressing LOOK gives you the ability to use graphics to make your guesses. On the screen shown in the...

  • Page 100

    XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 96 FIGURE 10.8.2 When the events are calculated based on Guessed data, they are represented by a dotted line 10.9 Calculated Data Prompts that are skip...

  • Page 101

    97 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 11.0 Edit Mode Within Program Mode, you can recall and re-input specific data prompt by prompt. When the Advanced Features Option is active the Edit Mode contains power...

  • Page 102

    98 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual : highlights data for editing. Only data that is highlighted and appears in the Data Input Line may be edited. Note: the EVT# (event number) and (event) TYPE...

  • Page 103

    99 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 11.2.3 Making Global Changes to Data Sometimes it is useful to be able to change data in a program without having to go through each event one at a time. For example, if ...

  • Page 104

    100 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual FIGURE 11.2.4 Pressing the Change All softkey highlights the Z feed for all the Mill events FIGURE 11.2.5 Type the new Z Fe...

  • Page 105

    101 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 11.3 Erase Program Use the ERASE PROG soft key to erase the program from the current memory. Erasing the program from current memory will not affect any programs that ar...

  • Page 106

    102 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual i01142 11.5 G-Code Editor (Advanced Features Option) The G-Code Editor allows the edit of G-Code programs that are opened as .GCD files. Once edited, the program may be r...

  • Page 107

    103 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Click in the Find What box and enter the item you want to find. Click on the Find Next box and the G-Code Editor will locate the next occurrence of that item. Successi...

  • Page 108

    104 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual i01147 12.0 Set Up Mode The Set Up Mode contains the tool library, the tool path and verify graphics and the machine's reference positions. Enter the Set-Up Mode by press...

  • Page 109

    105 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 12.1.1 The Tool Table Screen When you first enter the tool table by pressing the TOOL TABLE soft key, you will see the screen shown in Figure 12.1. Tool #: the number of t...

  • Page 110

    106 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual the Z DRO dimensions accordingly so you don’t have to touch off and reset after a tool change. The idea of retaining tool information in memory in order to reduce the am...

  • Page 111

    107 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Once the reference position is set, you will not be able to move the highlight back to the word "SET". Note: You must set an absolute zero reference in the DRO ...

  • Page 112

    108 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 2. Enter the amount of the adjustment you wish to make. To cut deeper, enter a negative number. To cut shallower, enter a positive number. In the example above, to corr...

  • Page 113

    109 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 12.2 Tool Path When the TOOL PATH soft key is pressed, the program is processed and the tool path graphics are displayed. i01143 FIGURE 12.2 The Tool Path graphics...

  • Page 114

    110 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual FIT: same as the FIT DRAW. : moves the drawing in that direction. ZOOM IN, ZOOM OUT: resizes the drawing. RETURN: returns to the previous soft keys, retaining...

  • Page 115

    111 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 12.3.3 Limit Positions X and Y limit positions (one for plus direction, one for minus) will stop the program if they are exceeded during run. Note that pressing the LIMIT...

  • Page 116

    112 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Press DEFINE STOCK if you wish to input dimensions of your rectangular stock relative to the programmed absolute zero. We automatically calculate and define the stock sl...

  • Page 117

    113 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual verification by pressing the STOP key and continue again using the GO key (use S and G on offline). Press SHOW PART to simply show the final result. Press EXIT or MODE...

  • Page 118

    114 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 12.6 Service Codes These are special codes that may be entered into the ProtoTRAK SMX CNC to call up routines used in installation, setting of preferences, machine chec...

  • Page 119

    115 XYZ Machine Tools, Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual Machine Set-up 11 Backlash Hysterisis Test Runs a routine that helps the system compute lost motion. 12 Feed Forward Test Caution! Machine parameters may change. Run th...

  • Page 120

    116 XYZ Machine Tools Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 13.0 Run Mode 13.1 Run Mode Screen Press MODE and select the RUN soft key. The display will show: i01144 Items on the Run Screen: Event counter: this will be the cu...

  • Page 121

    117 XYZ Machine Tools Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 2. Positioning of the Z axis is automatic in the 3-axis CNC, but in two-axis, the ProtoTRAK SMX CNC will prompt “Check Z” before a rapid move and “Set Z” for you t...

  • Page 122

    118 XYZ Machine Tools Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual The event number and type (and the repeat number, if applicable) being run is shown at the top of the screen. The current X, Y, Z absolute positions are shown in the inf...

  • Page 123

    119 XYZ Machine Tools Ltd. XYZ Turret Mill and ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual viewed as Tool Path in the Set Up Mode to initialize the Run Time Clock. Otherwise it will show 0.00. (Section 12.2) 13.7 Stop At any time, the program may be halted by...

  • Page 124

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 120 14.0 Program In/Out Mode From the Select Mode screen, press the PROG IN/OUT softkey. The first screen you see will ask: "LIST SUPPORTED PROGRAMS ONLY?" W...

  • Page 125

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 121A file extension that is unique to the ProtoTRAK SMX CNC is .GCD. The .GCD extension tells the ProtoTRAK SMX CNC that a particular program is a standard RS274, or G Cod...

  • Page 126

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 122 14.3 Opening a File To open a program file from a storage location, press the OPEN softkey from the Program In/Out Mode screen. The ProtoTRAK SMX CNC will always defau...

  • Page 127

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 123 FIGURE 14.4 The Save screen File Name: displays the name of the file that is in current memory. Save As: lists the formats for which the file may...

  • Page 128

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 124 FIGURE 14.5 The Copy screen The copy operation is in two parts. First, use the navigation procedure described in Section 14.2 above and highligh...

  • Page 129

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 125 NO: Press this if you do not want to delete. The delete operation will be aborted and the previous softkey selections will return. When the delete operation is finis...

  • Page 130

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 126 14.8 Backing Up In order to protect your important programs, it is a good idea to back them up regularly. That way, if a floppy disk or hard drive becomes unusable, yo...

  • Page 131

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 127ProtoTRAK SMX CNC on a machine that does not have a ProtoTRAK SMX CNC and vice versa. Each ProtoTRAK SMX CNC comes with converters for other ProtoTRAK and TRAK CNC’s. ...

  • Page 132

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 128ProtoTRAK SMX CNC could guess that the file to be converted was from a previous version of ProtoTRAK because of its file extension (.mx3). But since file extensions may...

  • Page 133

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 12914.10 ProtoTRAK and TRAK CNC Compatibility File exchange between the ProtoTRAK SMX CNC and other ProtoTRAK and TRAK CNC’s is possible because the ProtoTRAK SMX CNC is...

  • Page 134

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 130Since there are some feature differences between the CNC’s the process will generally yield a useable .mx2 or .mx3 program but with the following exceptions: Event or...

  • Page 135

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 131To run the G Code file directly, open the file using OPEN AS: G Code .GCD. The entire program will be brought into current memory. You will be able to view the tool p...

  • Page 136

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 13214.11.3 Valid Characters for Word/Address Sequences G Prepare to execute a G COMMAND ParseGcode M Prepare to execute a M COMMAND ParseMcode N Introd...

  • Page 137

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 133even for experts. There are instructions below to guide you through the most basic case of establishing a peer-to-peer network. Beyond that, you should consult a quali...

  • Page 138

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 134router will automatically assign IP addresses to your ProtoTRAK and computer, saving you a confusing step. 2. Obtain a sufficient quantity of twisted-pair category 5 ra...

  • Page 139

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 135i01138 4. Double click on the System icon 5. Select the Computer Name tab. 6. Do not enter the computer description here. ...

  • Page 140

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 136 i01137 7. Enter a name for the ProtoTRAK SX in the Computer Name box. We suggest something descriptive, for example “TRAK SX3”. 8. Enter a workgroup. This wo...

  • Page 141

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 137 i01134 9. Keep clicking OK until you get back to the Select a Mode screen. 10. You must now save the changes so that the ProtoTRAK control may retain your settings...

  • Page 142

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 138 i01130 3. In the Drive box, type in “E:” You must type in both the “E” and the “:”. See Figure 14.12.6 below. (Drive letters A through D are used by ot...

  • Page 143

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 139this step. Otherwise, if the SAVE option is visible, then you must click on it in order to persist any and all changes done in the previous steps. To connect other Pro...

  • Page 144

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 140 i01135 Figure 14.12.7 TCP/IP Properties. Add User/Password allows you to establish different users or passwords for the ProtoTRAK SX. This is not recommended beca...

  • Page 145

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 141Default protocols: TCP/IP Network log in: Auto TCP/IP set up: obtain IP address automatically DNS: Auto Gateway: Not used Wins configuration: Use DHCP for wins resolutio...

  • Page 146

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 142NET USE New connections will be remembered. Status Local Remote Network ------------------------------------------------------------------...

  • Page 147

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 143End of file format: the ProtoTRAK requires the % to show the end of the file. Characters after the % will be ignored. Beginning of an operation: the ProtoTRAK requires ...

  • Page 148

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 144G20 Input in inch G21 Input in metric G40 Cutter compensation cancel G41 Cutter compensation left G42 Cutter compensation right G54 Work coordinate system 1 selection ...

  • Page 149

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 1453. range: 0 to 99 B. sequence or line number, denoted <seq-number> 1. format (independent of units): dddd 2. leading 0 suppression 3. range: 1 to 9999 C. Unsigned...

  • Page 150

    XYZ Machine Tools Ltd. XYZ Turret Mill andProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 146G31 Skip function G33 Thread cutting G37 Tool length automatic measurement G38 Cutter radius compensation vector change G39 Cutter radius compensation corner rounding G4...

  • Page 151

    XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 147 15.0 Sample Programs 15.1 Sample Program No. 1 Basic 2½-Axis Program This program is designed to give you practice on programming 2½-axis events for 3-axis CNC progr...

  • Page 152

    XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 148 EVENT 1 Bolt Hole NOTES – center drill DRILL OR BORE # OF HOLES X CENTER Y CENTER Z RAPID Z END RADIUS ANGLE # OF PECKS FOR DRILL Z FEEDRATE TOOL # 1 5 ABS SET 0 A...

  • Page 153

    XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 149 FIN CUT Z FEEDRATE XYZ FEEDRATE FIN FEEDRATE TOOL # .25 SET 100 SET 250 SET INC SET 3 SET No change of feedrate This is the end of the program. 15.2 Sample Progr...

  • Page 154

    XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 150 EVENT 1 IRREGULAR PROFILE NOTES X Begin Y Begin Tool Offset Finish Cut Feedrate Fin Feedrate Tool # 0 ABS SET 0 ABS SET 1 SET .2 SET 250 SET 200 SET 1 References lower ...

  • Page 155

    XYZ Machine Tools Ltd. XYZ Turret Mill & ProtoTRAK SMX CNC Retrofit Safety, Programming, Operating & Care Manual 151 EVENT 6 AGE ARC NOTES Tangent Direction X End Y End X Center Y Center Conrad Radius Chord Length Chord Angle 1 SET 1 SET GUESS, 20 ABS SET GUESS, 100 ABS SET GUESS, 60 ...

  • Page 156

    XYZ Machine Tools, Ltd. ProtoTRAK UK Warranty Policy Warranty ProtoTRAK products are warranted to the original purchaser to be free from defects in workmanship and materials for the following periods: Product Warranty Period New ProtoTRAK 12 Months Any EXCHANGE Unit 6...

x